Search Documents

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining CO.'s Granite Mountain shaft. How this, insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the fire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest producer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The increase in the value of tripoli production was the result of an increase in the unit value. Emery increased owing to an in? crease in the volume of the material produced and an increase in the unit value. Special silica stone experienced a decrease in unit value and an increase in the quantity produced. Garnet showed a 10% in? crease in quantity and a 73% increase in unit value. Staurolite decreased about 8% in the quantity produced, and the value of production decreased about 10%. The fused aluminum oxide industry showed a 5% decline in the quantity produced and in the value of production. The silicon carbide industry saw a 10% decrease in the quantity produced and a 9% decrease in the value of production. Production for both industries decreased 7% in quantity and value compared with those of 1989.

Jan 1, 1993

By C. Watson Owings

"The mining Industry in the United States is becoming fully cognizant of the hazards of dust in underground mining as well as in surface plants. The dust problem in metal mines has been brought to focus through knowledge of the harmful effects of dust, especially silica, and through adoption of more or less stringent legislation classifying certain types of pneumoconiosis as occupational diseases. The coal-mining industry is aroused principally by the apparently great increase in the dust-explosion hazard resulting from the rapid growth of mechanized mining. The United States Department of the Interior, through the Safety. Division of the Bureau of Mines, has been requested repeatedly to recommend methods of allaying dust in both coal and metal mines. Methods adequate under hand-mining conditions fail to effect satisfactory reduction of dust in more rapid extraction with modern equipment. Studies of methods and equipment for allaying dust are being conducted in both metal and coal mines. Results of these studies are discussed, and indications of possible means of reducing dust concentrations are presented in the hope that the health and 'safety of men employed in the mining industry may be increasingly safeguarded.DUSTThe term ""dust"" is a common one, and yet the meaning is applied to widely different particle sizes. The general term means ""earth or other matter reduced to fine, dry, and powdery particles."" The root from which the word is derived means ""something that can be blown about by the wind."" As a result of tests on the explosibility of coal, the Federal Bureau of Mines has arbitrarily defined dust as being. ""that which will pass through a 20-mesh screen,"" based upon the fact that particles coarser than 20-mesh have little influence on the development of an explosion of Pittsburgh coal-bed dust. The study of dust, from a health standpoint, has given rise to still another definition of dust, namely,- according to Drinker3/, ""solid particles ranging in size from less than 1 micron to about 150 microns."" A micron is 1/25,400 inch, and 150 microns are approximately 1/1,700 inch. Atmospheric dust usually is considered as 10 microns or less, larger particles not being counted under the microscope in determination of dust concentrations."

Apr 1, 1942

The Bureau of Mines is operated to assist in promoting economic development through increased efficiency in the mining, preparation, treatment, and utilization of mineral substances; to aid in conserving mineral resources through preventing waste; and to help the mining industry improve health conditions and increase safety. Accomplishment of those ends is sought through investigation of scientific, technologic, and economic problems of the, mineral industries and dissemination of resulting information. Building materials of mineral origin constitute an important product of mining, and the Bureau makes studies of these in the various fields mentioned. The following commodities come within this classification: Asbestos, anhydrite, asphalt, cement, clay and clay products, diatomite, dolomite, glass and mineral wool, granite, greenstone, gypsum, lightweight building materials, lime, limestone, magnesite, marble, sand, sand and gravel, sandstone, sand-lime brick, slate, soapstone, and trap rock.

Jan 1, 1937

By John F. McCoy

The U.S. Bureau of Mines (USBM) awarded? a contract to Foster-Miller, Inc. to develop guidelines for designing, constructing, stocking, and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressuriztion Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By B. J. Moore

This publication contains analyses and related source data for 234 natural gas samples from wells and pipelines in 21 States and 1 foreign country. All of the samples were obtained and analyzed during calendar year 1975 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and n special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Seventeen previous publications have presented the results of 10,831 gas analyses prior to 1975. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 14

Jan 1, 1976

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

Many of the difficulties faced by the U.S. mineral industry in 1982 and 1983 emanated from the worldwide recession, from the high value of the U.S. exchange rate, and, in part, from actions taken by foreign governments to protect selected industries. While some problems will be minimized with continued worldwide economic recovery, others remain and may require special attention by U.S. policymakers. These problems include declining U.S. production capacity in selected mining and mineral processing industries, the impact of the high value of the U.S. exchange rate, and protectionist trade practices by competitor nations. Illustrative of the last is the International Trade Commission (ITC) determination in June 1984 that both the domestic steel and copper industries have been substantially injured by foreign imports. In its July 1984 recommendations to the President, the ITC suggested higher tariffs and quotas for 5 years on 70 percent of steel imports but conditioned the aid on cost-cutting and modernization steps by the domestic industry. In the copper decision, two commissioners recommended increased duties, two recommended that quotas be imposed, and one recommended that no relief be provided. The President decided in September to seek voluntary restraint agreements with nations that export steel to the United States and rejected both quotas and higher tariffs on copper imports. General Economic Setting This decade opened with the U.S. mineral industries struggling to deal with double-digit inflation, record high peacetime interest rates, and almost 7 years of oil-cartel-induced energy price increases that seriously affected the profitability of energy-intensive industries such as mineral production and processing.

Jan 1, 1985

By Peter L. Swanson

This investigation, which began 90 minutes after the February 3, 1995, seismic event, has benefitted from the assistance of a large number of individuals. These individuals provided information, data, analysis, brainstorming opportunities, field equipment, assistance with communication, conducted rock mechanics tests, and provided insight into mining in the southwestern Wyoming trona district. They include Rich Hodgson, Ron Hughes, Larry Refsdal. Mike Weller, John Kolesar, Joe Vendetti, and Rick Casey (Solvay Minerals), Dave Delling (Solvay consultant - former Solvay President), Karl Zipf (formerly with USBM, now with MSHA), Bob Friend, Bob Ferriter, Dave Ropchan, Jerry Davidson (MSHA Tech Support), Don Stauffenberg, Ben Hohler (Wyoming State Mine Inspector's office), Bruce Presgrave (USGS/NEIC), Chris Wood, Dan O'Connell (Bureau of Reclamation), Sue Nava, Jim Pechmann (University of Utah), John Norgord and members of FMC's mine rescue team (FMC Corp.), Bill Walter (Lawrence Livermore National Laboratory), Ron Gerlick, Kevin Wood, and Mike Harmel (USBM rock mechanics lab), Jim Case (Wyoming State Geological Survey), and Solvay consultants. In addition, many individuals helped us gather information on other recent large mining-related seismic events in Germany, Russia, and Australia. and other parts of the United States. These individuals include Wolfgang Minkley (IfG Institut fur Gebirgsmechanik, Leipzig), Arnfinn Prugger (Potash Corp. of Saskatchewan), Hartmut Spetzler (University of Colorado/ University of Bayreuth), Sergei Stanchits (Ioffe Poly-technical Institute, St. Petersburg), Rocky Thompson (Cyprus-Amax) and numerous seismologists throughout the Internet.

Jan 1, 2011

In this issue, the Bureau of Mines announces the availability of the latest of its Mineral Perspectives series: ?MP-4, mineral Industry of Western Europe." This publication describes the mineral industries of 19 Western European countries. For readers unfamiliar with this new series, reproduced below and on the two succeeding pages, is the section dealing with the mineral industries of France. Information regarding acquisition of this publication is found inside the back cover of this issue. FRANCE France is a moderately important producer of minerals, including iron ore, coal, potash, fluorspar, and uranium. In addition, France is a significant processor of imported minerals, chiefly for its own consumption. In general, it has exportable surpluses only of a little iron ore (low-grade ore exported to Luxembourg) and some nonmetallics.

Jan 1, 1977

Workers at the Consolidated Aluminum Corp. primary aluminum smelter at Lake Charles, LA walked out at midnight March 31 when their contract expired. Management personnel operated the smelter and prebaked carbon anode facilities until an agreement for a new 3-year contract was reached April 18. The Aluminum Company of America (Alcoa) began operations at its can recycling facility at Taylor, MS. The facility can process 3 million pounds per month of aluminum and steel cans. Alcoa announced plans to increase the capacity of its aluminum paste and flake production plant at Logan's Ferry, PA by 50 percent. Completion was scheduled for mid-1980.

Jan 1, 1979

By D. J. Parker

Because of its convenience and availability, natural gas (and to a much less extent manufactured gas) in being used more generally throughout the country for domestic and industrial purposes. With this use, specific and little-recognized hazards have arisen owing principally to the fact that the public and the consumer lack knowledge of the explosive property of this fuel. During the past 8 years gas explosions hove occurred in public and private buildings with loss of more than 300 lives and injury to many others. Such appalling catastrophes can and will be prevented if and when the necessary precautions are taken in the construction of buildings and the installation and maintenance of gas lines and gas appliances, plus adequate supervisions inspection, and education.

Jan 1, 1941

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By Albert L. Toenges

This circular deals primarily with the various methods of longwall mining used in some mines in certain districts of the Middle Western States. In some instances underground methods were considered comprehensively, and in others only the actual methods of mining and face advance were noted. Results obtained by the mines in output per man were compared only on the basis of an operating day, since idle time and number of men employed would not, be comparable due to the great difference between mines in different districts. Man-hours per ton per operating day are noted in a general way. Material and power costs are not included. ACKNOWLEDGMENT The information used in preparing this paper was obtained through the courtesy and cooperation of the presidents and other officials of the comparnies operating the mines described. The approval of the executive of each property was obtained for publishing this manuscript, and the accuracy was checked.

Jan 1, 1936

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982