Search Documents

By N. Graham, C. Walker

The SORD Miner is a patented mining principle being developed to exploit mineral and energy resources that current technology can not access. SORD Miner is designed to operate in underground wet, granular, continuously collapsing geological environments such as alluvial and marine deposits. It is somewhat like a cutter suction dredge and should be capable of mining its way through any fine granular material like sand or gravel, pumping the slurry back to the surface. In areas where the target layer is covered, the SORD Miner is inserted below the water table and will tunnel its way to the mineral deposits at depth. This paper describes the development, concept testing and prototype construction of the SORD Miner.

Jan 1, 2007

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

Underground mining and particularly dipping narrow tabular orebodies are difficult to mechanize appropriately, given the low gold price and other external factors. Particularly in the deep level mines in South Africa, there is little choice left but to mechanize if the industry is to remain competitive and a significant global player. This paper presents a design philosophy for appropriate mechanization intended to generate solutions that can be implemented using the people currently employed in South Africa mines. The design philosophy is based on the ability of high-pressure water (hydropower technology) to deliver enhanced performance to users and on simplicity in the eyes of the user. Four examples of systems and equipment are described to illustrate the approach to Appropriate Mechanization. These include: • The Development End System, • The Monorail Raise Climber, • Automatic Pump Control Valves, and • The Energy Recovery Pump. The equipment is presented with the following critical issues foremost in mind: Safety, Working Environment, Performance, Cost effectiveness and Implementation. Although the appropriate mechanization approach is described in the context of the South African underground mining industry, much of the Appropriate Mechanization equipment has worldwide applications. Key Words: Hydropower, Mechanization, Tunnel Development, Raise Development, Monorail, Raise Climber, Pump Control Valve, and Energy Recovery

Sep 1, 2001

By J. W. Wilson, J. G. Taylor

The mechanization of haulage drilling in the gold mines of Anglo American Corporation by J. w. WILSON, Ph. D., C.Eng., M.AIME, F.!.Min.E., F.I.M.M. (Fellow), and J. G. TAYLOR, A.C.S.M., C.Eng., M.!.M.M. (Visitor) Some one-thousand kilometres of tunnels are mined annually in the gold mines of South Africa. Until two years ago, mechanized drilling on South African gold mines was not an economic proposition because of the availability of inexpensive labour and the fact that mechanized equipment developed for other mining markets could not perform satisfactorily in the tough, abrasive quartzites of theWitwatersrand System. A project team from the Technical Development Services Organisation of the Anglo American Corporation, in collaboration with various manufac turers of drill rigs and drill steel, has been concerned with the development of suitable equipment for mechanized main-haulage drilling. After two-and-a-half years of extensive testing and development of drifters, drill steels, and bits, many of the problems encountered have been sotved, and gradually jumbos mounting pneumatically and hydraulically powered drifters are being phased into production on various gold mines of the Group. A description of the development work is given, and actual operating results are recorded, together with details of the drilling and blasting techniques used.

Jan 1, 1975

By T. Gibson

It is generally accepted that South African coal mines have gone through the mechanization of most of its underground mines, and while there certainly were a lot of productivity improvements, the lack of visibility on these machines operating underground still leave vast areas for improvement. The average actual cutting time still remains very low, in the 30 per cent area, which leaves significant improvement possible. Currently all analysis is carried out using hand-written reports. Unfortunately this is subjective and often inaccurate because of human interpretation. In addition in order to avoid costly component failure, a monitoring system is required to warn of eminent failures and condition monitoring. The challenge faced was to supply and install a system that was ‘Open’ and could be retrofitted to existing machines in operation because of the current standard of communication links to the underground sections. In addition it was intended to use, existing ‘off the shelf’ software and hardware and adapting this for the harsh underground mining conditions wherever possible in order to reduce costs. As development occurred, as with all technology, doors opened to other opportunities such as, remote access data logging and Internet based reporting. We focused on the Voest Alpine Bergtechnik (VA) range of continuous miners, as need arose to achieve the desired cost improvements because of the strategy of service contracts the subsidiary company, Voest Alpine Mining & Tunnelling (VAMT) offer the mining industry in South Africa. This paper describes a data logging system that has been installed on various continuous miners that provides data in real time, on line, and that could be expanded to any electrically supplied underground mobile or stationary mining machine.

Sep 1, 2001

By G. Newson, N. Runciman

In 1999, INCO Limited Mines Research, in Sudbury, Ontario, Canada, took delivery of a MeycoRobojet Logica Spraymobile, a computerized concrete spraying system. The Spraymobile is a self-contained mobile machine capable of applying spray-on ground support in underground applications. The Logica component of the Robojet is designed to control the operation of the Robojet, as well as scan and map the tunnel geometry prior to the spraying operation. The Robojet can be operated in various modes, from manual to automatic operation. In the automatic mode the computer controls the standoff distance, angle, and motion of the spraying jet. In 2000, INCO Limited, working with Meyco Equipment of Switzerland (a division of MasterBuilders Technologies), detailed a plan to create a tele-operation package for controlling the spraying process from a surface location at INCO's Mines Research Test mine. With the RobojetLogica operating in automatic mode, the operator at the machine becomes a process monitor. Since the Logica system controls the key spraying parameters of nozzle distance and nozzle angle to the sprayed surface, the operator could easily monitor and control the Robojet Logica from aremote location. The benefits of operating underground mobile mining (drills and LHDs)equipment from a surface location has been demonstrated at INCO Limited, however, the abilityto control a ground support operation (shotcrete spraying) from surface has not been attempted until now. This paper will describe the Spraymobile shotcreting system, the development of the tele-operation package for the Robojet Logica, as well as modifications to the original Spraymobile for implementing the tele-remote package on the Robojet Logica at the Mines Research test mine.

Sep 1, 2001

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

The February General Meeting of the Branch was held in the St. Helena Club at 8.00 p.m. on the 10th February, 1971. Mr G. Y. Nisbet (Chairman, O.F.S. Branch) was in the chair. There were also present: Seven Fellows: Messrs. N. A. Honnet, C. J. Isaac, J. M' Meyer, I. Thomas (Committee Members), J. Lorenzen, S. L. S. Swart and D. Waterman. Six Members: Messrs. R. Campbell, D. J. Couperthwaite, R. Cross, A. H. Edwards, C. G. J. Vermeulen and G. J. C. Young. Two Graduates: Messrs. J. McLuskie and M. H. Smith. Six Associates: Messrs. J. Dean, W. F. de Lange, J. S. Freer, A. Hooper, A. Paschalides and L. Vorster. One Student: Mr D. J. Hammond and nine visitors, a total attendance of thirty-two. Minutes As the minutes of the General Meeting held on the 17th November, 1970 had not yet been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. Office-bearers The Chairman informed the meeting that this branch had received the resignation of Mr J. N. Saunders. Following his resignation the Committee elected the following office-bearers: Chairman - Mr G. Y. Nisbet Vice Chairman - Mr J. M. Meyer The Chairman also announced that Messrs. J. M. Meyer and G. J. C. Young had been co-opted onto the Committee. General Members were advised that arrangements had been made for the Cookhouse Tunnel visit towards the end of March. Talk by J. Freer The Chairman called on Mr J. Freer to deliver his talk on "Uranium Extraction, Processing and Conversion for Fuel Element Manufacture". The presentation of this talk, illustrated by sketches, proved very interesting and entertaining and was received with applause from all present. Mr I. Thomas proposed a vote of thanks to Mr Freer on behalf of all members of the O.F.S. Branch. After thanking Mr Freer for his talk and all present for their attendance, the Chairman declared the meeting closed at 9.30 p.m.

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

On 23rd October, 1969, 54 members of the Institute set out at an early hour from Rand Airport in two chartered Dakota aircraft for a visit to the Hendrik Verwoerd Dam site. The weather was at the start rather unpromising but after passing Bloemfontein the overcast cleared and it turned into a glorious day for a most memorable visit. The Institute is indebted to U.C-Dumez-Borie Dams Limited, the main civil engineering contractors, and Mr J. D. McNamara their executive manager, for the very excellent arrangements made for this excursion. From the time the aircraft landed till a slightly belated departure the organisation of the extensive tours arranged for the parties was quite outstanding and a matter for congratulation to all concerned. At each of the many places visited there was a senior official to give an authoritative and comprehensive description of the work under his control. In addition the guides on the buses, loaned by the Department of Water Affairs, kept up an interesting running commentary throughout the day. A further much appreciated facet was the introduction of many of the experts on the site and a brief talk by each after an excellent lunch served at the recreation club. Each visitor also received a brochure with a progress report and a detailed site plan, with various sections highlighted in colour, and obviously prepared at the cost of much time and effort. The visit included tours of the large dolerite quarry, where some 150 000 tons of rock are removed each month, the 42 in. gyratory primary crusher, the secondary crushing and screening plant, the rod mill plant for sand production, and the automated blending and concrete batching plant. The transport of mixed concrete by 'silobuses' to the 6 cu. yd buckets of four Blondin cableways, two of which are radially movable and two with buffing towers, and the placing of the concrete in the huge blocks of the wall was watched from a vantage point. The most interesting part of the visit was without a doubt the inspection of the wall itself and the explanations of the many intricasies of its design and care in construction, covering aspects such as positioning of galleys, interlocking of blocks, reinforcement, refrigeration, actual concrete placing, subsequent grouting, etc. Other points of interest were the very complicated design of the wall itself, the river diversion plans, with three stages of coffer dams, the spillways, and the very well cut penstock tunnels.

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

By D. H. Diering

The paper deals with the technologies required for opening up anew idealized ultra-deep level mine. First the overall philosophy of accessing ore at ultra depths is discussed. Then the individual technologies which will be required are explored. Finally a detailed overview on one of the key technologies, namely tunnel support, is given. Because this project is still in its infancy, few definitive answers are provided; instead each of the envisaged technologies are briefly discussed, with emphasis on those which require the element of speed for rapidly accessing the ore body.

Jan 1, 1997

Council and Standing Committees, 1975-1976 President: Dr R. E. Robinson. Vice-Presidents: Dr M. D. G. Salamon and P. A. von Wielligh. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: Prof. R. P. Plewman. Members of Council: Dr M. G. Atmore, J. D. Austin, C. T. Fenton, J. A. Holmes, P. Holz, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Dr D. I. Legge, D. G. Malan, C. T. Shaw, D. A. Viljoen, R. A. von Maltitz, H. M. Wells. Chairman, Witbank-Middelburg Branch: E. J. Jackson. Chairman, Orange Free State Branch : G. J. C. Young. Past Presidents Serving on Council: R. J. Adamson, H. Britten, H. E. Cross, J. K. E. Douglas, R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson, P. W. J. van Rensburg. Seven Council meetings and five Executive Committee meetings were held during the year, and the standing and sub-committees held fifty-five meetings. Standing Committee Chairmen Membership, P. A. von Wielligh ; Technical Programme-Metallurgy, D. A. Viljoen; Technical Programme-Mining, D. G. Malan; Vacation School-Metallurgy, Dr P. R. Jochens ; Vacation School-Mining, H. M. Wells; Awards, Dr R. E. Robinson; Excursions, Dr D. I. Legge; Adjudicating, Dr R. E. Robinson; Constitution, Rules and Policy, Prof. R. P. Plowman; Mines and Works, C. T. Shaw; Education, Prof. R. P. Plewman; Foundry Colloquia, Prof. D. D. Howat. Representatives on Other Bodies Associated Scientific and Technical Societies: Members : Dr R. E. Robinson and Prof. R. P. Plewman. Alternates : P. A. von Wielligh and Dr M. D. G. Salamon. Federation of Societies of Professional Engineers: Members : J. K. E. Douglas and Prof. R. P. Plewman. Alternates: Dr R. E. Robinson and Dr M. D. G. Salamon. FSPE Technicians Committee: Member: D. M. Jamieson. FSPE Rationalziation Committee: Member: Dr M. D. G. Salamon. South African Council for Professional Engineers (Institute Nominees) Member : R. C. J. Goode. Alternate: G. H. Grange. South African National Committee on Tunnelling: Member : D. G. Malan. Alternate: Prof. R. P. Plewman. Engineers' Liaison Committee (Pretoria) Member : Dr J. P. Hugo. Alternate : P. W. J. van Rensburg. Government Certificate of Competency Liaison Committee: Member: Prof. R. P. Plowman. Alternate: D. M. Jamieson. James Moir Memorial Lectures: Member : Prof. D. D. Howat. World Mining Congress-National Committee: Members : Dr M. D. G. Salamon, Prof. R. P. Plewman, and H. M. Wells. I.F.A.C. Symposium: Member: P. W. J. van Rensburg (Chairman-Organising Committee). Alternate : Dr J. P. Hugo. I. U.P.A.C. Symposium: Member: Dr P. R. Jochens. Membership Nine Fellows, twenty Members, six Associate Members, thirteen Graduates, nine Associates, twenty-nine Students, and ten Company Affiliates were elected during the year. One Fellow was elected to Honorary Life Fellowship, eight Members and one Graduate were transferred to Fellows, twelve Graduates and two Students were transferred to Members, three Students were transferred to Graduates, and one Student was transferred to the grade of Associate. Six Fellows, two Members, and two Associates were admitted to retired membership. Nine Fellows, fifteen Members, three Graduates, one Associate, two Students, and one Company Affiliate resigned. A statement of membership as at June 30th, 1976, and the end of the previous year is shown in the following tabulation. 30th June, - 30th June, 1975 1976 Honorary Life Fellows 16 - 17 Honorary Fellows 8 - 8 Life Fellows 171 - 171 Fellows 549 - 547 Members 523 - 517 Associate Members 15 - 21 Graduates 132 - 123 Associates 209 - 205 Students 173 - 179 Company Affiliates 71 - 80 1866 -1878 Obituaries Your Council records with deep regret the death during the year of the following members: P. A. Creewell, Life Fellow; A. S. Davis, J. S. Hay, P. 0. Lange, N.

Jan 10, 1976

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa's total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low 'effective stoping width' should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the 'bull wedge' and 'explosives' in Fig. 1 of the paper were no further from the ideal point 'A' than was 'cutting'. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas 'faces' of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008