Search Documents

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By Jurij Karlovšek, Wolfgang Angerer, Vojtech Ernst Gall, Jacob Grasmick

The International Tunneling Association (ITA) Working Group (WG) 22 “Information Modelling in Tunneling” has developed a guideline for the implementation of Building Information Modeling (BIM) concepts for Bored Tunneling Projects. The guideline primarily covers the use of BIM during the conceptual and delivery phases of a project. It provides Owners with an introduction to BIM, an overview of the current capabilities of BIM, and a guide for implementation for a Bored Tunnel. The document will be officially published at the World Tunnel Congress (WTC) in Copenhagen in 2022. This paper describes the need for the guideline and provides a preview of its contents.

Dec 1, 2022

By Christophe Bragard, Jason Choi, William H. Hansmire

This case history provides a physical benchmark of tunneling technology progress comparing an old hand-mined tunnel to a modern 20-ft-diameter EPB TBM that mined in the same ground. This rare opportunity to see how tunnels were constructed many years ago occurred when an old 10-ft-diameter storm drain tunnel in the way of os Angeles subway construction was demolished and replaced with obas berglass pipe. Steel rib and lagging initial support was exposed showing solid-sawn 2" × 12" × 48" redwood lagging. This paper documents the as-built old tunnel, how it was successfully replaced, and some lessons learned.

Jun 23, 2024

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By M. J. DeJong, R. J. Mair, S. Ritter, G. Giardina

"For urban tunneling projects it is essential to predict and prevent building damage. Although various case studies and experiments have shown that buildings considerably modify greenfield soil movements, widely accepted damage assessment methods neglect this soil-structure interaction and simplify structures as linear elastic beams. This paper summarizes an experimental investigation of the response of more realistic structures to tunneling-induced deformations. Small scale structural models with façade openings and brittle material properties were 3D printed and tested in a geotechnical centrifuge. Soil and structure displacement data were obtained by image-based measurement. Results demonstrate that structures notably mitigate differential greenfield ground displacements. It is also shown that maximum soil settlements, horizontal soil displacements beneath the structure and structural damage in the form of cracking significantly depend on the position of the structure in the settlement profile. The results provide a basis from which to predict building settlement response with greater certainty. INTRODUCTION With continuing population growth and increasing urbanization expected in the next decades, there is an urgent need for a next generation of infrastructure. It is likely that a large part of this infrastructure will be underground. Such creation of urban underground space frequently involves the excavation of shallow tunnels in close proximity to existing structures and utilities. For example, along the Crossrail project in London more than 1,200 structures are located within a possible influence area of the tunnel construction (Torp-Petersen and Black 2001). The assessment of building damage plays a vital role throughout the planning, design and construction stage of urban tunneling projects. However, while predictions of tunneling-induced deformations in the greenfield can generally be made with some confidence, much uncertainty exists about how structures interact with ground movements arising from tunnel construction."

Jan 1, 2016

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By Art Hamid, Manfred Wong, Carlos Jaramillo, Greg Raines, John Caulfield

"The Central Bayside System Improvement Project (CBSIP) is a critical element of the Sewer System Im-provement Program (SSIP), a 20-year, $6.9-billion investment by the San Francisco Public Utilities Commis-sion (SFPUC) to upgrade San Francisco’s 100+ years old seismically vulnerable combined sewer system. The CBSIP’s centerpiece, a proposed 10,000-foot-long (3,048-meter-long) Channel Tunnel, will provide reliable and redundant gravity conveyance and storage of combined wastewater flows from the northern and central parts of San Francisco to the Southeast Water Pollution Control Plant (SEP) while ensuring compliance with regulatory requirements for combined sewer discharges to the Bay. A tunnel with a diameter of 23 to 30 feet (7 to 9 meter) is being planned using pressurized-face tunnel boring machine technology. Project challenges include tunneling through Franciscan Bedrock, mixed ground conditions in close proximity to the Bay, connector tunnels and shafts, construction in congested urban environment, and challenging real estate issues for shaft access. BACKGROUND AND NEED FOR TUNNEL The City of San Francisco is one of the most beautiful cities in the world. About 850,000 people live in the city and many more come to work, for tourism, and for attending conferences. The SFPUC is a department of the City and County of San Francisco that provides energy, drinking water and wastewater services to San Francisco, wholesale water to three Bay Area counties, and green hydro-electrical and solar power to San Francisco municipal departments. The SFPUC wastewater system includes tunnels, large storage/transport boxes, 1000 miles of collection sewers, 28 pump stations, and three wastewater treatment plants. San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. After decades of service, much of the sewer system is nearing end of its working life. During the 1989 Loma Prieta earthquake, damage to SFPUC water and wastewater infrastructure was extensive. The 11,200-foot-long (3,400-meter-long), 66-inch-diameter (1,676-mm-diameter) Channel Force Main, built in 1976, and a critical component of the SF wastewater system was also damaged. This force main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the SEP. The force main is at the end of its life and was not constructed to the current seismic code; in addition it has no redundancy. Figure 1 shows the project background and the force main that will be provided redundancy by the new gravity tunnel."

Jan 1, 2016

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By Xuehui Zhang, Yun Bai, Qiaosong Li, Huiming Wu

"Construction activities account for a large share of the global Greenhouse Gas emission. In the past 10 years, project decision-makers and researchers have been paying more attention to the carbon emission of tunnel projects. In this paper we study the carbon emission calculation in shield tunneling. The objective of this paper is to: (1) analyze the complex variables which affect the total emission of shield tunneling; (2) develop and illustrate a new data-mining-based method to estimate the carbon emission in the construction phase; (3) assess the emission prediction reliability of a data-mining-based method—the Randomforst model, with R programming language. This study is based on a large-diameter shield tunnel built in Shanghai, China, and shows that a reliable predictive performance can be achieved with this new data-mining-based method. INTRODUCTION Climate change caused by the Greenhouse Gas (GHG) emission has been a hot topic in recent 20 years. Both governments and non-government-organizations are trying its best to control the climate change. Since the 1990s, the general consensus is that carbon emission reduction and carbon sinking (the work of capturing the emitted carbon) are two ways of mitigating the global warming effect, with the former being more exercisable. The challenge posed by global warming also motivates the project decision-makers to take measures to reduce the GHG emission. The 5th Assessment & Report on Climate Change (published by IPCC, the Intergovernmental Panel on Climate Change) suggests that building industry contributes to 5% of the total direct emission. The building industry has shown more awareness of the impact of GHG emissions with construction activities. Shield tunnels act as an important component of the infrastructure system, and have been the dominant way of utilizing the underground space, as well as a competitive alternative to passageway underneath rivers. To study the environmental effects of shield tunneling, there is a need to quantify the carbon emission of shield tunnel construction."

Jan 1, 2016

By George E. Williamson, Mikiya Higuchi, Michael T. Traylor

Extensive soil conditioning was required to allow Earth Pressure Balance(EPB) tunneling on the South Bay Ocean Outfall tunnel project in San Diego, California, near the Mexican border. This tunnel extends 19,000 feet out under the Pacific Ocean and was mined through soil formations including silts, sands, gravels, cobbles, and boulders. EPB pressures ranged from 3.0 to 7.0 bar, with the maximum pressures required when mining through the highly permeable granular formations.

Jan 1, 1999

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By Dave Ragland

The SDSU tunnel and underground station are the first of these type facilities to be constructed by the Metropolitan Transit Development Board. Because there is no previous experience, and because tunneling activities are associated with some risk, he MTDB has undertaken a very proactive and wide reaching program to identify and control risks during construction. Finally, because the tunneling activity and underground station is on the San Diego State University, MTDB is working closely with their staff to identify construction impacts and mitigation’s, and thus ensure a quality project for both agencies.

Jan 1, 2001

By Morris Loshinsky, George Ziegler

The New York City Transit System is celebrating its Diamond Jubilee this year. In 1904, 9.3 route miles of New York's first subway was placed in operation in lower Manhattan. Since that date the system has grown to 230 route miles and 458 stations (See Exhibit #1). The age of the system immediately provides a clue to the nature of our construction activity. While we must always plan for the future and expand the system in the direction of the future needs in New York, a substantial amount of time and money must be channeled towards the modernization and maintenance of the existing system which provides vital transportation for 3-1/2 million passengers a day. This paper however will be directed to our New Route's Construction and, specifically, to three rock tunnel and cut and cover sections presently under construction. Currently, New York is engaged in the construction of about 9 New Route miles of structure. Briefly, the 3 Sections we will discuss are as follows: Route 131-A Section 5A is a 4 track structure in Manhattan and includes the new Lexington Avenue Station. This 1240 foot long section is located between Park Avenue and 3rd Avenue and is a combined cut and cover and rock tunnel section under 63rd Street. Route 131-A Section 5B is an intricate 2423 foot long 4 track rock tunnel section extending from 3rd Avenue to the FDR Drive under 63rd Street in Manhattan.

Jan 1, 1979

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By Ulf Georg Gwildis

Overexcavation and ground loss events during pressurized-face TBMadvance in soft ground can result in unplanned deformations above the tunnel and damage to existing infrastructure. Successfully managing the risk of this occurring is crucial for any project in an urban area to proceed. Common risk management approaches include a combination of establishing suitable ranges of TBM operational parameters and using geotechnical instrumentation for deformation monitoring. Another risk management tool is material flow reconciliation, which varies depending on the specified mining method and the equipment choices by the contractor. This paper compares recent and ongoing projects in the Pacific Northwest regarding overexcavation risk management.

Jun 13, 2023

By R. M. Ocampo-Franco

The line seven, as part of the development of the Subway Master Plan in Mexico City, will tunnel under different subsoil conditions of clay with high water content and low shear resistance located between 8 and 12m beneath the surface. Boulders in silty sand and gravel to a 40m depth underlay this stratum. Economics, scheduled time of construction, and the obligated interconnection with existing lines one and two determined the construction of the tunnels to have an overburden of 1.0 to 2.2 times the diameter. In the north part of line seven there is a track of 251m length that was decided to attack with an open shield of 9.14m of diameter due to the characteristics of the sub-soil, minimum section needed as well as a minimal overburden, of 10.41m. The paper explains the construction procedure from the excavation stage to the reinforcement of the final lining obligated for the ground subsidence as a result of volumetric changes of a stratum of 4m thick of clay overlying the crown of the shield. Manuscript not received in time for publication.

Jan 1, 1983

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By Dietrich F. C. Hudewentz, Alfred H. F. Lücker

For centuries tunnellers have made use of the experience of miners. In West German coalmining tunnellers have returned the impulses in recent years by giving the miners valuable stimuli with the result that a technology has evolved which benefits drill and blast heading, opens the door to TBM heading and has developed special measures for difficult strata conditions in deep coal mines. WHAT DO THESE ROCK HEADINGS LOOK LIKE? The main roadways dealt with in this paper have crosssections of 20 to 40 m2, big enough to allow the massive airflows needed to aircondition the mines. Because of the difficult strata conditions they have to be supported: in shotfired headings mainly with multi-element arches, in TBM headings with rings of 6 to 6.5 m diameter. In West German coalmining the majority of rock headings are blasted. The proportion of rock headings driven by TBM was 11 % in 1980 and 16 % in 1981, a rising trend expected to continue. Drill and blast headings Drill and blast headings are normally equipped with two or three-boom electro-hydraulic jumbos, electro-hydraulic crawler-mounted loaders with 1.2 m3 shovel capacity, a movable working platform and both chain and belt conveyors for dirt clearance to the minecar loading point. Fans and air-condition plant complete the equipment. Spacing between arches is usually 0.8 m. Investment for this type of mechanisation works out at around 1.3 m DM.

Jan 1, 1983