Search Documents

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By G. R. Green

The centre of the mining operations of the International Nickel Company, Ontario Division is Sudbury, a city of 160,000 population located 240 miles northwest of Toronto (Fig. 1). Within thirty miles of this city and located around the rim of the geological formation known as the Sudbury Basin are the ten underground mines and one open pit operated by the Company (Fig. 2). There are also four developing mines, three in the Sudbury area and one at Shebandowan, near the city of Thunder Bay, Ontario and approximately 150 miles north east of Duluth, Minnesota. In 1971 the mines produced 22,800,000 tons, 20,600,000 tons from underground and the balance from open pits. Also located in the Sudbury District are facilities to extract and refine the metals contained in the ore. There is a nickel refinery located at Port Colborne on Lake Erie. An additional nickel refinery is under construction near Sudbury. Fifteen elements are recovered from the Sudbury ores, nickel, copper, iron, sulphur, gold, silver, cobalt, tellurium and the six platinum group metals, platinum, palladium, iridium, rhodium, ruthenium and osmium. In 1966 a major expansion program was undertaken to meet increasing market requirements. Coinciding as it did with a severe

Jan 1, 1972

By Ian S. Ross

The emphasis in this paper is focussed on dry bulk car go or the same cargo converted to slurry form for ease of handling. It is this type of cargo which is of primary interest to the mining industry whose products it represents to a large extent. The design problems associated with the handling of liquid bulk and of unitized cargo are sufficiently different to be treated separately. This paper then will consider the port handling facilities of dry bulk commodities as part of a system consisting of (1) the movement of products to the port area, (2) the movement of products out of the port area and (3) the handling of products within the port area itself. Expanding within these three components of the total transportation system, the paper will discuss the various difficulties encountered concerning the mode of transport into the port area and the method of handling product from transport to stockpile. Secondly, and before discussing the port area itself and in order to complete the conditions under which the port must operate, the movement of products out of the port area will be covered dealing with such items as the accommodation of the ship, problem associated with the very large ships, optimum berthing arrangements and the need to consider the various costs associated with the vessel. Finally the paper will review within the port or interface area such items as stockpiles, method of recovery, inventory control and an outline of the common design difficulties encountered. In all cases the relative influence on the total transportation costs of each of these dry bulk transportation system components will be considered.

Jan 1, 1972

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By G. L. Mowrey

In addition to developing various types of coal interface detection systems, the U.S. Bureau of Mines is actively involved in developing a coal rib thickness monitoring system for high wall mining applications. One particular system that appears to show promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1995

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By B. Li

"Sepiolite is a magnesium-rich, porous, and fibrous clay mineral with broad applications. These applications take advantage of sepiolite’s high specific surface area and unique nano-sized channel structure. Over the past years, numerous materials and techniques based on the structure and property of sepiolite have been developed. This article reviewed the recent achievements in developments and applications of sepiolite in environmental protection, catalysis area, and nanocomposites. The prospectives of sepiolite applications is also discussed. INTRODUCTION Sepiolite is a magnesium-rich, porous, and fibrous clay mineral. The typical chemical formula of sepiolite is Si12Mg8O30[OH]4[OH2]4·8H2O [1]. Sepiolite has a high specific surface area and nano-sized channels because of its special structure [2]. This unusual crystal structure projected onto the [001] plane is shown in Fig.1 [3]. As it can be seen, silicon and oxygen atoms make up for the tetrahedral structure and magnesium and oxygen atoms form octahedral structure, respectively. Those tetrahedral-octahedral-tetrahedral ribbons expand boundlessly in one direction, leading to the special fibrous structure of the sepiolite. Every tetrahedral-octahedral-tetrahedral ribbon is combined to the next by an inverted Si–O–Si bond, which causes an interlaced layer with a continuous tetrahedral sheet and a discontinuous octahedral sheet. Terminal MgO at the edges of the ribbons is coordinated with two structural water molecules, which can form hydrogen bonds with zeolitic water molecules that are located in the channels running parallel to the fiber axis [3,4]. The Mg2+ ions inside the channels can be exchanged with other cations in solution. Therefore, sepiolite can be used to remove metal cations from aqueous solutions [5,6].It can be seen from Figure. 1 and Table 1 [7], the unique structure endows sepiolite with a substantial surface area and nanoscale channels. Its specific surface area reaches 320 m2/g and channel dimensions up to 3.7×10.6 Å. There are three active adsorption sites on the surface of sepiolite: one is oxygen atoms of the Si-O tetrahedron. The second is the structural water molecules paired with magnesium ions at the edges of the ribbons, which can form hydrogen bond with adsorbent. The last one is the Si-OH groups due to the breaks of the Si-O-Si bonds on the surface of Si-O tetrahedron. Thus, sepiolite has strong adsorption ability which has been widely used in environmental protection. Moreover, sepiolite has many significant features such as good mechanical and thermal stability, rheological property, porous, and easily modification, making it be a hotspot in chemical and biological researches. However, with the development of technology, broader and more advanced applications of sepiolite have been carried out in recent years. In this study, the recent achievement in sepiolite applications is summarized, the further tendency is also discussed."

Jan 1, 2018

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972