Search Documents

By Bhawani Singh, A. K. Dube, B. Singh

At least three hydroelectric tunnels constructed during the last decade through the lower Himalayan region in India have met with serious problems of supporting in squeezing ground conditions. Steel ribs under went intolerable deformations requiring rectification to provide space for concrete lining which delayed the projects inordinately. In an attempt to choose a rational method of predicting rock load, the authors have compared rock loads estimated from various classification systems and elasto-plastic theory with observed values. The deficiencies of the classification systems have been highlighted to show that the combination of elastoplastic theory and tunnel instrumentation programme provides better guidelines for the design of tunnel supports in squeezing ground conditions.

Jan 1, 1981

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By P. Marcheselli, Jean-Yves Peron

A twin tube tunnel of 2 000 meters long and an internal diameter of 6.90 m has been excavated through alluvial ground, with low overburden, using a 8.0 m diameter Earth Pressure Balanced tunneling machine with foam injection and extruded concrete behind segment.

Jan 1, 1995

By Robert J. Auber, Thomas R. Scotese

The West Leg Interceptor is part of a new sanitary sewer system in the southwest suburbs of Cleveland. The first two construction contracts were excavated in glacial soils varying from hard tills to pressurized silts and flowing sands. These soil and groundwater conditions were locally problematic during shaft and tunnel excavations and final lining construction. A variety of solutions were developed primarily during construction. During the WLI-1R Contract, subgrade pressures, continued ground losses, and displacements necessitated extra eductor wells and modified inverts for stabilization of shafts. At the WLI-2Contract, one shaft excavation in similar ground required only one extra well. In the WLI-1R tunnel, localized inflows of groundwater, silt, and sand through the geotextile fabric were stopped by cement grouting. In one WLI-2 connector tunnel, damage to the TBM flood doors combined with wet, flowing silt and sand led to ground losses, surface settlements, plugging, patching, and chemical grouting. The concrete lining in the main WLI-2 tunnel required remedial work to improve watertightness at joints.

Jan 1, 1999

By Kenneth R. Maser

In the past 30 years, great advances have taken place in the development of tunnel boring machines, raise drills, large diameter drills and blind shaft borers that have revolutionized the shaft sinking and tunneling industries. Techniques for placing concrete linings, however, have not changed significantly during this period, and still constitute a stumbling block to the achievement of the rapid construction. In the past 5 years, Foster-Miller Associates, Inc. (FMA) has been involved with the development of a remotely operated shotcrete system for lining raise drilled shafts, an Extruded Tunnel Lining System (ETLS) for lining TBM bored tunnels, and a Continuous Shaft Lining System (CSL) for lining any type of machine bored shaft. This paper presents an overview of these three developments, including capabilities and limitations, a description of the concrete production, concrete placement, and advance rate, and control subsystems, a description of the concrete mix development required for each system, a discussion of test results to date, and an assessment of the state of development of each concept. Plans for future development will also be presented.

Jan 1, 1981

By Eugene F. Casey

The next ten to fifteen years will be exciting ones for the construction industry because three city agencies alone have started or will start, on tremendous expansion programs, the cost of which will exceed a total of four billion dollars. The major portion of this work will be done by the use of tunnelling methods. *Tunnelling is construction by any method of a covered cavity of predesigned geometry whose final location and use under the surface, whose cross-sectional area is greater than two sq. meters. The New York City Transit Authority's expansion program will provide for approximately 52 miles of new subways. The Board of Water Supply has already started on City Tunnel No. 3 which, when completed will provide the City with enough water until the year 2000, and the Board of Water Resources has embarked on a tremendous program to clean up the surrounding waters. Yes, these will be exciting years, particularly when one reads about the new novel exotic methods of rock breaking and disintegration, coupled with the new methods of soft ground tunnelling.

Jan 1, 1997

By Don Macfarlane, Brian Heer, Tom Martin

The Manapouri Power Station, commisioned in 1969, is located in Fiordland National Park in the South Island of New Zealand. It is the country’s largest hydro power scheme and can generate 700MW of electricity. The power station utilizes the hydraulic head of Lake Manapouri, using an underground power station and a 10 km-long tailrace tunnel was constructed by drill-and-blast to allow discharge to Doubtful Sound. Power generation fell short of expectations due to higher than expected friction in the tailrace system. To remedy this a second tailrace tunnel was constructed between June 1998and May 2002. It consisted of a 10 m diameter, 10 km long tunnel in predominately gneissic rock and was excavated using an Atlas Copco Robbins TBM. High water inflows, Owner/Contractor production incentives and a major claim settlement were handled during the 5 1/4 year project. This paper discusses TBM advance rates, utilization factors that increased in the second half of the project plus an innovative method for sealing Tunnel 1 to construct the bifurcation.

Jan 1, 2003

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By Heinz Distelmeier

The New Austrian Tunneling Method was, as is well known, developed from conventional rock tunnelling. In Germany about 10 years ago the NATM began to be applied to partially stable soils by incorporated excavation and support methods to allow its use with these soils. The advantages of this tunnelling technique - adaptability, ecomomy, and quality have resulted in its widespread usage. Today, about 85 % of all mined tunnels in Germany are produced with this technology. This rapid development has resulted in about 40 companies operating within a geographical area about the same size as the state of Illinois that are capable of utilizing the NATM. In most cases German contract/award procedures allow the contractor to develop alternate design and plans. As a result of this flexibility and intense competition, safety factors have been gradually reduced to the lower limit of what could be regarded as demonstrably safe, and the utilization of the NATM has expanded to include higher risk conditions, namely * excavating larger cross sections. * working with less overburden. * work undertaken under less stable soil conditions.

Jan 1, 1983

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

By Pieter Barendsen, Olivier Dubugnon

INTRODUCTION There are three fronts on which development efforts are being concentrated to extend the application domain of Tunnel Boring Machines (TBM), which is potentially very large - Assessment of a reliable prediction method, including machine-rock interaction and geological characterisation, so that the boring system can be designed properly and the costs remain in the predicted range for each given tunnel project. - Development of lighter, more flexible and more controllable machines to be applied in shorter, deeper tunnels or roadways, such as required in mining. - Reduction of cutter and machine costs when excavating hard rocks or difficult grounds, in developing improved tool materials, cutting geometries and tunnelling systems. The above three lines of development have a common, critical requirement: to have a reliable set of design rules to optimize the machine specifications from the knowledge of rock and geological parameters and working requirements. This optimization can only be done if a model sufficiently sophisticated is made available, able to take into account the numerous factors influencing the TBM advance , and being interactive enough to achieve the optimization.

Jan 1, 1985

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By Lee W. Abramson, William H. Hansmire

The H-3 Project is planning, design, and construction of a 10-mile (16 km)-long final segment of new highway that traverses the Koolau mountain range in Oahu. Interstate H-3 traverses North Halawa Valley on one side of the Koolau Mountains and Haiku Valley on the other side. The project includes a tunnel through the mountain range. The one-mile (1.6 km)-long twin-bore Trans-Koolau Tunnel will have two lanes in each direction. The total roadway width including shoulders in each bore will be 38 ft (11.6 m). The geologic and geohydrologic conditions along the alignment present a variety of tunneling problems. Geologic conditions consist of volcanic materials deposited generally in fairly thin basaltic layers. These volcanic materials generally weather down to "MH" soils which are compressible but relatively strong. Perched ground water that is recharged by heavy rainfall is present in the mountains. The paper presents results of initial geologic surveys and exploratory boring, and plans for exploratory tunneling and testing programs. A site specific classification method developed to characterize the weathered profile is presented.

Jan 1, 1989

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008