Search Documents

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By Aloys H. Wohlrab

THE conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8 -in. steel show that when bit sizes are reduced from I ½ in., I 3/8 in., and I 3/16 in., to I 3/8 in., I ¼ in., and I 1/8 in., respectively, the volume of the hole is 15 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I.826 in., a difference of 0. 2,5I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and I4° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5.6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1942

DD3-tunnels (PD BH's) ? Rotary coreholes 111no. (124) ? Percussion holes Ono. (37) ? Sampling (rock and soil) ? Soil and rock permeability ? testing ? BH Televiewer Surveys [ ]

Jan 1, 2007

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By F. B. Harris

MINE surveying and engineering at the various properties of the United States Smelting Refining and Mining Company has developed and increased in importance steadily as mining methods have changed and expanded, both in the development of ore bodies and in the methods and styles of stoping. Most important to satisfactory engineering practice, and secondary -only to accuracy and precision, is the preservation of all data relative to surveys and calculations so that it is readily available for use at all times and in -such form that it is permanent, easily found, and usable. The first consideration for a proper, accurate, and practical start for surveys and efficient engineering at any property is an accurate triangulation net and system of co-ordinates. This has been our practice and the first step seas to select a base line, readily accessible and easily measured, situated preferably on an even grade where the difference of elevation between the two -end monuments was not too great and -the distance was long enough for practical use. Permanent concrete monuments were built for these base-line points so constructed that they could be easily recognized and were visible. Precise levels were run on this base 'line and the elevation (sea level datum) if possible was established at each end monument. The distance was carefully measured many times, back and forward, by using a tape that had been standardized by the National Bureau of Standards. The tape was supported at ,each 25-ft interval on stakes which had been brought to grade between each measuring point. All conditions were

Jan 1, 1948

By Xianxin Shi

In surface electrical exploration the high resolution earth resistivity method (HRRM) is a very effective method for detecting abandoned drift mines workings. When the abandoned mines are more than 500 ft (150 m) deep, its detection capability reduces greatly and requires more effort to implement. In Yan Quan coal mine, Shanxi province, we tried to adapt this method for underground application. Two survey lines were designed with the spacing of current and potential poles 20 m and 10 m, respectively and measuring points at 2m. The measurement radius of I line and I1 line were 140 m and 60 m, respectively, and the infinitely far pole was 1200~2000 m from the survey line. (Note the I and II lines are located on the north and south ribs of main tunnel, respectively). The survey results showed that abandoned workings were located at 25-70m, Survey Line I and at 80-1 10m, Survey line 11. Based on this finding, the longwall panel gateroads and set up entry were properly located thereby providing safe mining of the No. 15 Coal seam. Key Words: Abandoned coal mine, High resolution earth resistivity, Underground electrical exploration

Jan 1, 2005

By Rene Padilla, Siyanda B. Mngadi, Gerrie van Aswegen, Peter Stonestreet

While many mine tunnels are developed through ground that must be riddled with the sources of small (and larger) mining induced seismic events, recorded by the mine seismic monitoring systems, we do not see planar discontinuities classified as seismic sources in the geotechnical databases. Here we list criteria that may be useful to identify discontinuities in drill core which are dynamic slip surfaces, parts of mining induced seismic sources. Such shear rupture surfaces in core would generally be powdery, cohesionless, and rough on cm scale. Finely broken rock and rock flour may be found in the core boxes at the discontinuities. Slickensides would be soft (easily destroyed) and kinematically consistent with the local stress field. In some cases, a cross fabric would be present, orthogonal to the slickensides, being the intersections of en-echelon extension fractures, within the dynamic shear zones, with the shear zone walls.

Apr 26, 2022

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Theophili CN, Kapenis AP

Seismic tomographic imaging has been applied to determine the blast induced damage zones in bauxite pillars in underground mining. At the retreating stage, when pillar dimensions are reduced from 8 x 8 m to approximately 5 x 5 m, the' seismic tomographies reveal, through measurements of the P-wave velocities which is a measure of the degree of fracturation of the pillar rock mass, the presence of three zones within each pillar. In the external zone, where velocities recorded are below 750 m/s. extensive pillar damage occurs which is attributed to both the growth and coalescence of pre-existing cracks and even the creation of new cracks in the rock mass. This effect is in agreement with literature, when considering the peak particle velocity as a criterion for rock failure in tunnels. In the intermediate zone, where velocities range between 7S0-1000 m/s, damage to a much lesser extent occurs which is due mostly to growth of pre-existing cracks and widening of their apertures. The inner zone, where velocities exceed 1000 m/s, is considered to be unaffected by blasting. Simple remedial measures of low cost, which are based on blasting mechanics are proposed to minimise the blast induced damage zone and consequently the transition zone.

Jan 1, 1995

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described

Feb 1, 2020

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By S. Shimaya, T. Maejima, M. Shimo

"The authors conducted the in-situ gas-tightness tests in a fractured rock at the Namikata underground LPG storage site in Ehime prefecture, Japan. The test consisted of two independent setups, a gas-tightness test that used boreholes, and a chamber-scale test that used a horizontal drift sealed with a concrete plug. In each test, the gas pressure was increased up to the onset of the measurable gas flow to obtain the maximum containment pressure. This paper discusses the hydraulic conditions for gas leakage initiation and the importance of the pore pressure measurement for monitoring the gas-tightness of the LPG storage cavern based on the test results.INTRODUCTIONJapanese first underground LPG storage plant was constructed by JOGMEC, the Japan Oil, Gas and Metals National Corporation, at Namikata in Ehime prefecture in granitic rocks (Kato et al., 2007). The “hydraulic sealing principle” (Åberg, 1977) that utilizes groundwater flow into an unlined cavern to prevent the leakage of gas through fractures in the surrounding rock mass was employed for storage of LPG. This paper describes the results of the in-situ tests performed at the Namikata Site to obtain information on fundamental gas-tightness characteristics of fractured rock. Two types of in-situ tests, a borehole gas-tightness test and a chamber gas-tightness test, were carried out near the storage caverns. Figure 1 shows the cavern layout of the Namikata underground storage plant and the test locations. The storage facilities consist of three caverns (W26m×H30m×L485m). The cavern crown lies at a depth of 150m below the sea level in Cretaceous granitic rock (Figure 1). Water curtain boreholes excavated from the water gallery tunnel at EL-125m level are located above and side of the caverns to prevent water drainage from fractures during the construction stage as well as during operation. The borehole tests were performed from a drilling adit excavated from the eastern end water gallery tunnel, while the chamber test was conducted at the southern edge of an exploratory drift extending from the central water gallery tunnel."

Jan 1, 2015

By D. R. Piteau, A. MacG. Robertson

Strength, permeability, and deformational properties of a rock mass are influenced and often controlled by the geological discontinuities within the mass. These properties are often determined by physical tests conducted within and on portions of the rock mass under consideration. Any extrapolation of these test results to other portions of the rock mass assumes that a similar pattern of discontinuities, having similar properties, exists throughout the region of extrapolaion. A survey in which various joint properties of interest are measured may be conducted to sample the joint population of the mass. Suitable data manipulation and handling techniques are developed to permit the definition of the joint population of the rock mass. The validity of the extrapolation of test results may then be assessed.

Jan 1, 1974

By A. Eitzenberger

This paper describes a study of seismic records from the Kiirunavaara mine footwall which were interpreted in relation with numerical models developed outside the study. Seismic data was retrieved from a portion of the mine and filtered with respect to the ratio between energy carried by an event's P (primary) and S (secondary) waves (Es/Ep ratio), local magnitude, and active mining depth. The data was analysed using Es/Ep ratios and Gutenberg-Richter graphs to determine the event origin, mechanisms, and minimum magnitude cut-off. The magnitude completeness was identified by studying the b-value stability and b-value differentiation between origin sets. It was shown that, by separating seismic events into the origin components shear, complex, and tensile based on Es/Ep ratios, a representative value for the magnitude completeness can be identified for a catalogue with a convex cumulative log curve. The majority of the events were shown to be of shear-slip origin based on the recorded Es/Ep ratios, with pure tensile events constituting only about 10% of the recorded data. Spatial and temporal event location patterns were studied and compared with numerical modelling results. The comparison showed a correlation between shear-slip seismic events and volumes experiencing high differential stresses in the lower part of the footwall. In the upper part of the footwall the results did not reveal any clear correlation between observed damage in drifts and seismic event locations. The concentration of seismic events in the lower portion of the footwall is discussed in the context of rock mass displacements. The results indicate a possible connection between mine seismicity at depth and damage observations in the drifts in higher non-seismic areas by seismic softening and subsequent lateral expansion of the rock mass.

Jan 1, 2017