Search Documents

By Thomas R. Scotese, John L. Ackerman

The Hanging Lake Tunnel Project represents a major portion of the Glenwood Canyon Project, the last piece of Interstate 70 to be constructed. The project features twin bore, large span rock tunnels and six open cut portal excavations, all excavated by drilling and blasting. This paper presents descriptions of the methods used by the Owner and Engineer to control and monitor the drilling and blasting practices in the tunnels and in the portal areas.

Jan 1, 1992

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By John A. Bischoff, Francis S. Kendorski

A technique that has been used for inspection and appraisal of rock tunnels is described. It enables a rapid and complete record to be made of those factors necessary for the engineering assessment of the rock conditions surrounding a tunnel. Full understanding of the regional geology, and a careful recording of data concerning the principal geological and construction factors is essential basic data for a tunneling project, whether the tunnel is under construction or is already in service. A methodical recording of data concerning general geology, shears, fracture orientations, spacing, persistence, rock classification, water condition, shear frequency, excavation method, blasting procedure, and rock stabilization and support methods, combined with a photographic record, can be completed by experienced engineers and geologists at the rate of over 1000 feet of tunnel per shift.

Jan 1, 1976

By Robert M. Adler

In order for a taxpayer to produce income, he may be required to exhaust his capital assets. With respect to the mining industry, those exhaustible capital assets may result in income tax deductions under the general categories of depreciation, obsolescence, losses and depletion. The percentage depletion deduct ion concept is not based upon "economic" depletion, or "geological" depletion theories. Instead, it is wholly an income tax concept created by Congress. This is significant in that, in its application, tax depletion has no adherence to traditional economic or geological depletion concepts For example, the Internal Revenue Code limits percentage depletion to 50 percent of the miner's net income for the taxable period.1/ Should a particular miner extract and sell 500,000 tons of material during the year, but at a loss, he receives no percentage depletion. The same would apply to an electric utility which mined its own coal. Should its mining costs exceed the "going price" for coal, as established by actual arm's-length sales in the market, the utility has no net income, and is therefore not entitled to percentage depletion.2/

Jan 1, 1973

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By Maynard O. Serbousek, Melvin E. Poad

Shotcrete, a useful support material in underground openings, is a sprayed concrete, and, when used with fast-setting agents, is immediately self-supporting. Although shotcrete has been used extensively for tunnel support, the technique has not been readily accepted by the mining industry because of the lack of essential information on such basic items as material properties and rock interaction. The Spokane Mining Research Center (SMRC) of the Bureau of Mines has been active in the field for the past 2 years, including research on fibrous reinforced shotcrete. IIT Research Institute, Chicago, under Bureau of Mines contract, is investigating physical properties of shotcrete as affected by (1) type of process (wet or dry) and (2) fast-set agents and controlle-dset cements. Already the contractor has shown the advantage of a regulated-set cement over normal cement and fast-set additives for the dry process. The regulated-set cements can produce high early strengths with no decrease in ultimate strength.

Jan 1, 1997

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

By D La Rosa, G Power, K Riihioja

In underground mining, the often unpredictable variability in ground conditions may lead to the application of suboptimal drilling and blasting patterns, resulting in poor performance. Experience and pertinent information to develop and implement improved drilling and blasting strategies can be easily lost due to the lack of means to help engineers store, access and manage this information. The Julius Kruttschnitt Mineral Research Centre (JKMRC) through a series of industry funded applied research projects has been developing a system that can facilitate the drill and blast design, analysis, auditing, documentation and data management processes. The system is a hybrid between an information management software module called BMS (Blast Management System) and two design and analysis modules, 2DRing for underground production blasting activities and 2DFace for development blasting activities. A concise description of the software tools and its applications are given in this paper, supported by two case studies. Opportunities to further develop the software are also highlighted, they include options to integrate these tools to existing drilling and blasting automation systems and portable computing technology to facilitate the design, implementation and continuous improvement processes.

Jan 1, 2001

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023

By P. A. Rusin

Many manganiferous silver deposits remain undeveloped because standard chemical extraction methods yield poor recoveries or are ' environmentally unacceptable. Biotreatment of such ore deposits in our laboratory resulted in manganese and silver recoveries of greater than 90%. Ore and sediment samples were collected from mining sites in Colorado and Arizona. Portions of samples were incubated in a semi-solid mineral salts medium amended with 20 mM glucose mid manganese dioxide (Mn medium). The cultures were incubated at 3(fC until manganese reduction was detected by a .color change fr:om .black to clear. Bacteria from these cultures were purified on Tryptic Soy Agar and individual isolates were retested for Mn reduction by an agar overlay method. Bacteria were identified according to Bergefs Manual ?of Systematic . Bacteriology. Most of the Mn-reducing bacteria are Bacillus species. Bacterial manganese reduction kinetic experiments were performed in 52 ml mineral salts broth supplemented with manganiferous silver ore instead of manganese dioiide. These cultures were incubated with agitation for 16 d. Aliquots were removed periodically and analyzed for solubilized manganese by atoniic absorption (AA). Cyanide (1,0 M) Vias added to the remaining ore-medium mixture for a 24 h bottle roll. The supernatant was analyzed for soluble silver by AA. Similar experiments were conducted on a larger scale using 15% pulp density. After bfotreatment of the ore, standard bottle rolls were performed. The pregnant solutions and the residues were analyzed for manganese and silver?using AA or fire assay as appropriate. In sterile. controls-which received no biotreatment, manganese and silver recoveries were 0.3% and 10% respectively; During biotreatment, total manganese solubilizatiori was as high as 99.8%. The reduced manganese could . be stripped from ?the growth medium using hydrometallurgical techniques. Silver recovery vaned from 70% to 92.5%. Microbial treatment of refractory mangairlferous ores can result in high recoveries of manganese and silver. Retention time varies depending upon the relative concentrations of manganese, silver, and other metals in the ore with only two days required in some cases, The biotreatment of ore is environmentally' acceptable while the use. of chemicals such as sulfur dioxide is less so.

Jan 1, 1991