Search Documents

By James A. Pappas, Francis L. Fong, Tracy K. Lundin

The impact of environmental regulations on the quality of tunnel groundwater discharges is examined in this paper. Tunnel contractors usually depend on specialty contractors or outside consultants to deal with this issue without carefully examining their activities to minimize the production of contaminants. This approach may not be adequate given increasingly more restrictive environmental requirements. This paper surveys the general practice of the tunneling industry and attempts to identify sources of contaminants which may affect the total suspended solids, oil and grease content, and pH of the discharges. Strategies for treating the discharges are included. Field data and observations from several tunneling projects are also presented.

Jan 1, 1995

By David R. Wayman

This paper summarizes environmental compliance and related issues associated with underground construction and tunneling operations, whether new work or rehabilitation. Underground construction and tunneling operations have (in most cases) both an underground and surface component. Since many of the major tunneling projects occur in urban areas, often is areas inhabited for several decades or centuries, environmental problems may already exist in a project area, though that may not yet have been formally recognized. Large projects often attract more than their fair share of regulator attention. This paper addresses the issues with the greatest potential to be encountered by underground constructors, with the emphasis on minimizing contractor liabilities, both in the short- and long-term. Minimizing contractor liability begins with understanding bid documents, contract provisions and necessary means of protection, and carries through project execution by responsible control of hazardous materials, avoidance of media contamination, proper waste disposition, as well as compliance with other environmental requirements.

Jan 1, 1999

By J. Palarski

Hard coal, mined in Silesia Region as well as in the eastern part of Poland, is a key national resource. In Polish underground coal industry, modern mining technologies have been successfully tested and used in the last 50 years. More than 98% of the coal produced underground is extracted by longwall mining method. Current underground coal mining expands into increasing depths. The use of conventional coal extraction methods ? room and pillar and longwall with caving - is becoming increasingly difficult. The coal mining is modifying existing methods and is testing innovative technologies. Backfill is an important component of modern underground mining operations. In Polish underground mines, backfill is recognized as an integral component for extraction of coal from greater depths in a densely populated environment. The modifying and innovative methods require the use of backfill or grouting of caving to provide structural support in underground excavations and to ensure that the mining operations are safe. Depending on the geological structure, mining conditions and environmental requirements there are several variations of longwall methods used in underground coal mining in Poland, in particular: longwall with caving, longwall with backfill, longwall with grouting of caving area. This paper will discuss the different components of an effective longwall production and filling process of caving area. The paper will give a overview of the current application of backfill technology, focusing on Polish coal mining operations. This paper will also briefly describe how backfill contributes to an innovative method ? underground coal gasification. The paper discusses specific requirements for fill materials and the technology of backfilling for underground coal gasification (UCG) operations and problems of implementation and correlation of backfill parameters with other processes that occur during thermal processing of coal.

Aug 1, 2013

By T. Murt, C. Oñate

In recent years, environmental considerations have played a prominent role in underground construction projects. The management and disposal of the muck produced by an EPB TBM is an important aspect of this topic. Soil conditioners with higher biodegradability and lower eco-toxicity have been specifically developed to comply with strict regulations in several countries around the world, with the goal of reducing the environmental impact of tunneling on soil, water, and living organisms. This paper highlights innovative sustainable soil conditioners and how they differ from traditional products. Additionally, environmental considerations for TBM projects around the world and in North America will be examined.

Dec 1, 2022

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By Werner Burger

Earth Pressure tunnel boring machines are tackling difficult ground conditions that five years previous were not considered feasible. The technology has evolved that allows EPB TBMs to cross into areas that with the latest in conditioning and special design considerations are now possible to mine. This paper will review the various recent developments and those projects where these new techniques have been applied.

Jan 1, 2008

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By Craig Bournes, David Chapman, Michael DiPonio

Historically, boulders are a frequent source of problems in soft ground tunneling. During tunnel construction, the need to manually break and remove boulders as obstructions causes delays to the project. Repairs to a tunnel boring machine (TBM) can also be a source of delays. Managing these problems is difficult since normal soil investigation techniques do not accurately predict the presence or frequency of boulders. This has lead to considerable number of claims for extra costs and delays during the construction of soft ground tunneling projects. These issues are exacerbated in pressurized face tunneling systems where there is limited access to the TBM cutterhead for obstruction removal and/or cutterhead maintenance. The project team that built the Big Walnut Augmentation/Rickenbacker Interceptor (BWARI) Project for the City of Columbus successfully managed the design and construction of a 4,267 mm (14 ft) diameter soft ground tunnel with high boulder concentrations in a complex geologic setting. The management of the boulder issue tookplace during several phases of the project.

Jan 1, 2007

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By L. A. Ayres da Silva, J. P. G. Negri, A. L. M. Ayres da Silva

"Rock hardness is dependent on the type and quantity of the various mineral constituents of the rock and the bond strength that exists between the mineral grains. As the book “The Complete ISRM Suggested Methods For Rock Characterization, Testing and Monitoring:1974-2006” explains, hardness is a concept of material property. As such, the quantitative measure of hardness depends on the type of the test employed.Among the three types of tests that have been used to measure the hardness of rocks and minerals: 1) indentation tests; 2) dynamic and rebound tests; 3) scratch tests, the authors of this paper chose indentation tests, more specifically the Vickers test, and complementary verified the correlation between the results of the Schmidt sclerometer tests (rebound tests) and the Vickers microhardness tests in a set of the same 9 (nine) granite rocks.The objective of this research was to verif y the correlation of one created index, based on the Vickers test that can be able to represent the rock material hardness. We know that Vickers tests determine the microhardness of individual rock minerals. A pyramidal shaped diamond is applied to the surface with a specified force. The area of the permanent residual deformation divided by the applied force is a measure of the hardness. Using the relative participation of the mineral components of the rock, we established a hardness index denominated EVM (Equivalent Vickers Microhardness).The correlation of the EVM with others strength properties and application parameters like UCS (Uniaxial Compressive Strength) to study sawability of granite blocks have presented very good results. The association of equivalent microhardness with others strength parameters, allowed to find powerful algorithms for analyzes of the rock materials behavior under diversified circumstances, as the sawability of granite blocks, as we can see in Fig. 1.Other very interesting correlations were found as the EVM values and that were obtained by the use of the Schmidt impact hammer for the superficial hardness determination."

Jan 1, 2015

By F. C. Turin, K. M. Cornelius

1. INTRODUCTION Underground mining in the USA has undergone significant change in the past 20 years. Two key elements have been increased mechanization and a more educated work force in spite of these changes, many jobs continue to be labor-intensive and repetitive in nature. They entail tasks that, performed over time, can take a toll on the soft tissues and joints. The problem may be compounded by an aging mining workforce. In 1996 the mean age of the coal mining work force was 45 years and the median total years of experience was 20 (NMA 1998). As a person ages, the body resilience to chronic wear and. tear is reduced, which may cause a worker to pay an increasingly higher health price for performing the same task. Mining companies, like many others, are becoming more aware of cumulative effects to the worker as reports of these types of injuries rise. . Conducting a job analysis is an important step when considering a job redesign or modification to reduce worker cumulative trauma exposure. A basic approach to job analysis is to examine the types of aches and pains reported, the tasks performed, and work site conditions. The US Bureau of Mines (USBM) conducted an evaluation of roof-bolting tasks performed at an underground coal mine concerned about early warning signs of cumulative trauma. This evaluation will comprise the primary focus of this chapter. The approach used for the roof-bolting race study may be applicable to other work environments. 2. FUNDAMENTALS OF CUMULATIVE TRAUMA EXPOSURE Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders that affect the nerves, tendons and muscles. Common examples include lower back pain, tendinitis and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may not appear immediately, but can take weeks, months or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute there to a single event. In fact, it is more common to identify factors that may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTD) have been commonly used to refer to disorders that have occurred due to work-related activities. Three main risk factors contribute to CTD: force, repetition and awkward postures. Any one or combination of these may contribute to the development of CTD. Therefore, the design of equipment in conjunction with the required tasks should be evaluated when attempting to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list (Putz-Anderson 1988), describes ergonomics concerns that, overall, should be minimized at the work area: • Crowding or cramping the worker: a work area layout may unnecessarily constrain movements of the worker. • Twisting or turning: placement of tools and materials may require the worker to twist the spine to fulfill the requirements of the job. • Repeated reaching motions: the layout of the work area may require the worker to lean to reach and grasp the necessary tools and controls. • Misalignment of body parts: the arrangement of the work area may require the worker to frequently have one shoulder higher than the other or have the neck or spine bent to one side. While many of these concerns are a function of equipment design and environmental conditions, making workers aware of these issues may help them to adapt their work habits to reduce risk of injury. Additionally, this information is useful when conducting an ergonomic evaluation of a work area and associated tasks. 3. UNDERGROUND MINING ENVIRONMENT The underground mining environment is a unique challenge. It is more difficult to develop controls for an underground mine site as compared with a factory setting where equipment and facilities can be more easily designed to reduce worker force, posture and repetitive exposures. In an underground mine, workers are required to perform labor-intensive tasks that often cannot be avoided due to environment constraints. The dynamic nature of the environment does not allow easy implementation of mechanical assists to reduce force exposure. Many of the tasks performed by workers are repetitive. Restrictive work areas due to low ceiling height, low lighting levels and large pieces of equipment cause workers to perform these tasks in postures that are not desirable. Designers of underground mining equipment can control how a machine will function, but not the environment in which it will be used, Hazards in an underground mine cannot be completely removed by redesigning the system. There are many hazards and information sources that must be continually monitored by workers including their position in relation to large pieces of mobile equipment and unpredictable geological anomalies. Thus, immediate dangers may take priority over awareness of ergonomic considerations while performing a job. 4. CASE STUDY OF UNDERGROUND ROOF BOLTING 4.1. Roof Bolting and Cumulative Trauma Exposure In an underground coalmine, after an area is mined it is necessary to support the roof to keep it from collapsing. Since 1950, the primary method for supporting the mine roof has been installation of roof bolts. Long bolts installed into the roof compress the layers of strata achieving a uniformly distributed support anchorage. Roof bolts, typically 6-8 feet long, are installed by workers using large roof-bolting machines. There are different types of machines

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By P Crorkan

Within the framework in which future exploitations for Codelco-Chile Divisi=n El Teniente are situated, regarding the deepening of its reserves and the geotechnical problems that affect their recovery, it becomes strategic to evolve with new variants, which make deep mining possible. Codelco ChileÆs Divisi=n El Teniente is progressing within its long-term planning the exploitation of a sector called Esmeralda, which includes its removal through the gravitational caving method (panel caving). It is planned to use pre-caving, which basically consists of developing and undermining the undercut level, without having developed the infrastructure of the production and transport levels. This is carried out in order to achieve a better redistribution of the stresses, thus obtaining higher quality in the infrastructure development of these levels as well as less risk. The extraction reserves for this area, estimated through the opportunity cost selection criteria, were determined at 348 million tons with an average grade of 1.014 per cent Cu. The project carried out geological and geotechnical studies in order to prevent the geomechanical risks of the sector to be exploited, which is a site conformed totally by primary ore. Lithologically, it occurs mainly in Andesite, located at the western limit by Brecha Braden Pipe. There are also varieties of porphyries and hydrothermal breaches of anhydrite. The Esmeralda Mine production program will increase from 4000 tpd (average) in 1998 to its 45 000 tpd rate of production estimated for the year 2005. The approved investment for the period 1995 to 1999 is $US 150 million, out of a total $US 213 million for the project. At feasibility study level and before the project, it showed a Net Present Value of $US 342 million, an Internal Rate of Return of 37 per cent and an IVAN indicator of 2.3 for a ten per cent discount rate and a copper price of 100 US cents/lb.

Jan 1, 2000

By T. Marcher, C. Mathiesen, M. Allende, S. Bauer

"A unique pumped hydro storage facility using the ocean as a lower reservoir, combined with solar PV to create consistent, clean power will be presented: the Espejo de Tarapacá Project is comprised of a 300 MW seawater pumped storage hydroelectric plant using the Pacific Ocean as its lower reservoir and an existing natural concavity at the desert as its upper reservoir. The plant site is located in Chile’s northern coast 90 km south of Iquique. The site is characterized by a rocky shoreline and about 600 m of flat terrain moving inland, with an abundance of rock outcrops, after which there is a steep 700 m cliff. The power house and all waterways will be underground. The main focus is to present the rocks being expected in the underground works. As one of the actual most tectonically active regions of the world the seismic activity is particularly relevant and will be outlined in the presentation. INTRODUCTION Valhalla Energy is an independent Chilean-owned power development company. It focuses on the development, ownership and operation of renewable power projects. Valhalla was founded in 2011 with the goal of developing Chile’s natural renewable energy resources and strategically diversifies the country’s energy matrix away from an overdependence on imported fossil fuels. Valhalla began developing pumped storage hydro projects to provide scalable, clean, competitive, and reliable electricity by combining Chile’s superior solar resources with the country’s unique and extensive coastline suitable for storage.The capacity for renewable energy supply is driven by two distinct and unique natural characteristics found in northern Chile: (1) the abundant and reliable solar irradiation in the Atacama Desert and (2) a coastal site that benefits from a steep cliff and a natural concavity both within a relatively small land mass (see Figure 1). There are several potential sites in the northern part of the country that can be developed. The “Espejo de Tarapacá Project” is the first one to be built and subject of the present paper."

Jan 1, 2016

By M. du Plessis, J. P. Gouvea

Mesh based areal support is commonly applied in South-African deep-level gold mines. It forms part of an integrated support system that can cater for both rockfall and rockburst incidents. The application has been successfully applied over many years. Operations have different geotechnical conditions and practical considerations, which has led to the development of various types of mesh and integrated mesh-based support systems (i.e. meshing and lacing versus welded or chain-link mesh sheets). Typically rolls or sheets of mesh is pinned with rockbolts to the surface of an exposed excavation. Applications vary from hangingwall coverage in a conventional stope gully to complete excavation coverage in footwall drives of conventional mines or on-reef drives in massive mechanised mines. It is however critical to understand the behaviour of the rockmass and apply suitable support systems.

Apr 26, 2022