Search Documents

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Seedsman R

The fundamentals concepts of roof support are similar between coal mining, metal mining and tunnelling and yet there are different design approaches, different hardware, and different levels of site investigation. This should not be the case and this paper discusses the key geotechnical issues that should underlie all roof support design - the need to reinforce defects. A design method to build a beam in laminated rock under high horizontal stresses is presented. The method allows for changing rock strengths, defect properties and varying horizontal stresses. At one level the design can be implemented with design charts and tables. Lessons learnt during the implementation of the designs at 5 different mine sites are Discussed.

Jan 1, 1998

By B Yang, S M. Aminossadati

Transporting coal by means of conveyor belts is very common in Australian underground coal mines. Major conveyor belt-related mining incidents are now relatively infrequent as a result of recent improvements in engineering standards and use of fire-resistance materials. However, conveyor belts have the potential for incidents capable of causing either personal or structural damage. In addition, any unexpected break down of rolling components or failure of belts creates a significant interruption to the production that is a major concern for operators whose responsibility is to achieve the optimum mining production.Currently, underground coal conveyor belts are examined for the presence of any overheating, smouldering or unsafe conditions likely to cause a fire. Periodic inspection of operating conveyor belts is carried out with the aim of detecting any local heat sources in an early stage. This includes temperature measurements of the driving head, idlers and rollers using hand-held temperature sensors such as infrared cameras or laser temperature sensors. The disadvantages of current conveyor belt temperature monitoring systems include high labour and equipment costs, safety risk to personnel who are in close proximity to moving conveyors, the ability to take line of site measurements only and potential for missed overheated idlers. Some of the conveyor idlers in underground coal operations cannot be accessed for traditional temperature measurements. This introduces a significant risk to the operation of critical infrastructure.A distributed temperature sensing (DTS) system can be used to develop an advanced conveyor belt temperature monitoring system that provides real-time, accurate and continuous temperature measurements along a conveyor belt particularly at the rolling components. The DTS system comprises of fibre optic detection cable, DTS controller and interfacing module. The advantages of the system include the accuracy, low-cost, easy installation, robustness, safety, immunity to radio frequency and electromagnetic interference, real-time data collection, and secure data transmission. This paper presents a scoping study on the development and utilisation of a fibre optic-based DTS system for underground coal conveyor belts. The mechanism of heat generation, the operation temperature range and the installation issues of fibre optic cable along the conveyor belt particularly in close proximity to each end of the spindle on every idler will be discussed.CITATION:Aminossadati, S M and Yang, B, 2013. A scoping study on fibre optic-based temperature monitoring of underground coal conveyor belts, in Proceedings The Australian Mine Ventilation Conference , pp 35-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Henry G. Granger

NOTHING in this paper is to be understood as even suggesting a moment's suspension of the splendid work now going forward on the Isthmus of Panama, except so far as it is related to the proposed locks. All the work already done, and all material purchased or ordered, would be available for the plan herein proposed. The situation and the problem concerned may be summarized as. follows : The scheme of a lock-canal through the Isthmus of Panama was adopted, as is well known, on two principal grounds-namely, the greater expense of a sea-level canal, and the longer time required for its construction. Of these, the latter is believed to have been the more influential. But further developments have diminished the weight of both, so that a reconsideration of the question is warranted. It is the purpose of this paper to advocate such a reconsideration-emphasizing the importance of certain objections to the lock-canal not mentioned or not duly appreciated in the report of those members of the International Board of Consulting Engineers who favored this form; showing the nature and bearing of the new facts developed; and, finally, proposing a combination of well-known methods and apparatus, which would, in my judgment, effect the construction of a sea-level canal in less time, and perhaps at no greater cost, than will be required for the remaining work on the lock-canal. I. OBJECTIONS TO A LOCK-CANAL. 1. Earthquakes. Two centuries ago Panama is said to have been destroyed by an earthquake. In 1882 a rather violent earthquake was felt at the southern end of the Isthmus. In 1898 I felt a slight shock near the present border-line of Colombia. In 1900 I felt three shocks at Quibdo, the head of navigation of the

Jan 1, 1909

By Lewis M. Haupt

Discussion of the paper of Mr. Granger, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 25, January, 1909, pp. 1 to 37. LEWIS M. HAUPT, Philadelphia, Pa. (communication to the 'Secretary*) :-This subject is of great interest to me, and I am noting progress and conditions as a test of my own judgment in advocating what I believed to be the nearer, cheaper and better route at Nicaraugua. I have as yet learned nothing to change my views, or modify the convictions which led me to retire from the Commission; but that is not the issue to-day. Our government is committed to the Panama route, and is bound to " make good." There are many points presented by Mr. Granger which seem to me worthy of very serious consideration. But when all is said there remains the risk of seismic convulsions, to which either form of canal is subject; and I fail to see that the risk would be reduced by making the cut deeper, with greater surcharge of lateral pressure upon the side walls. A severe earthquake in the rainy season would doubtless close either type of canal. One of the arguments in favor of the Panama route most insisted on, was that Nature had provided good natural harbors at its termini. Recalling this, it has interested me to note that the cost of creating the necessary harbors is estimated at $27,000,000. Mr. Granger refers to this, and quotes the Board's report to the effect that, on the Atlantic side, it will require 5 miles of jetties to " make an excellent harbor out of a wretched one." The vulnerable part of Mr. Granger's paper seems to me to lie in the admission that the plant required is still in the embryonic stage, and that at least one machine should be built and tested " to demonstrate that the theoretical strains and forces work out in practice exactly as expected." This, how-

Jul 1, 1909

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By Pawan Bharadwaj, Wim Mulder, Thomas Tscharner, Guy Drijkoningen, Rob Jenneskens

"The Earth’s properties, composition and structure ahead of a tunnel boring machine (TBM) should be mapped for hazard assessment during excavation. We study the use of seismic-exploration techniques for this purpose. We focus on a seismic system for soft soils, where shear waves are better and easier to interpret than compressional waves, as has been shown over the last decade. The system is intended to be deployed on the machine’s cutter head, with a few seismic sources and sufficiently many seismic sensors to tackle spatial variability and noise characteristics. An important property of the newly developed system is its ability to process data with very little human interaction. Images need to be available in near real time, without human interactions slowing down the imaging process. This can be achieved by employing Full Waveform Inversion, which minimizes the difference between modeled and observed data. Because this method may suffer from local minima in the cost function if the data lack low-frequency information, we employ a dedicated seismic source that can generate sufficiently low frequencies for the relevant length scales. With data acquired in a number of field settings that mimic realistic TBM configurations, we show that the designed seismic system can successfully look ahead of the TBM and offers a valuable capability to support decision-making during tunnel excavation. INTRODUCTION While excavating a tunnel with a Tunnel Boring Machine (TBM), the geology and the ground conditions along the planned tunnel trajectory need to be investigated in order to safely and efficiently carry out the underground operations. This entails detecting the occurrence of boulders, foundations, pipes and faults, necessary to prevent hazards and time-consuming delays in the tunnel boring operations. In order to facilitate ground prediction ahead of a TBM, techniques as used in seismic exploration can be deployed. Two components common to seismic-exploration techniques are data acquisition and processing, the latter including inversion. We will discuss each of these for the application to tunnel excavation with TBM, in particular for soft soils."

Jan 1, 2016

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By Ashutosh Kumar Bharati, Rajesh Rai, B. K. Shrivastva, Arunava Ray

Opencast mining method is one of the most productive mining methods available at present, which is generally associated with the removal and handling of a huge amount of overburden material. Hence it imposes a serious challenge of dump slope stability and that too, mainly in the case of internal dumps. The study is primarily focused on the stability of dragline dumps and the subsequent development of a rating system to classify the stability of dragline dump profiles. Initially, numerical simulation is executed through RS2 (Version 9.0) software, which is based on the finite element method. Thereafter, simulation results are used to perform the sensitivity analysis of various geometrical and strength parameters of the dump slope, and the two-factor interaction method is also incorporated into the analysis, this method included the dependency of closest parameters while calculating the sensitivity index, and thereafter, it is converted into the rating of each parameter. The strength parameter like the angle of friction and the geometrical parameter like slope angle of the bench between the coal-rib roof and dragline sitting level are assigned the highest rating value. Based on the overall rating of the dragline dump, the dump slopes are classified into various classes, viz., very safe, safe, vulnerable, unstable, and highly unstable. This classification proved to be handy in the quick estimation of the stability of the dragline dump and also gives an idea of designing optimum and safe dragline dump profiles. The developed classification chart has been validated by the previous research works and has found similar results.

Feb 15, 2021

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By Peter Mathias

The ventilation of long headings tunnels has al- ways posed special problems. The authors trace the progress of one such project from the design stage through the practical problems encountered to the final solution.

Jan 1, 1980

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019