Search Documents

By Irwan Halim, Young Jin Park

A new tunnel lining was designed for rehabilitation of the existing unlined Weehawken Tunnel in New Jersey. Structural assessment using beam spring models was performed for the lining design as a drained structure at the invert with a waterproofing umbrella. Empirical Federal Highway Administration (FHWA) guideline was typically adopted for estimating hydrostatic pressure, which recommends full hydrostatic pressure at the crown and ten or twenty-five percent gradual reduction from the initial pressure toward the invert. Finite element seepage analyses were conducted for the actual conditions based on anticipated drainage behind the lining and impact on the structural design. Considerations will be provided on the existing guideline for estimating hydrostatic pressures.

Dec 1, 2022

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By M. T. Long

The Crestmore Limestone Mine of Riverside Cement Company in Riverside, California is situated within 1.6 km of the Santa Ana River. It is an alluvium covered deposit with a massive quartz manzonite intrustion separating the upper and lower limestone beds which dip from 30° to 50°. The highly fractured upper bed contacting the Santa Ana alluvium contains many unique water inflow problems which vary, from multiple high pressure 19 liters per minute inflows up to 3,000 liters per minute to 11,000 liters per minute inflows-contacted by development mining in April 1983. A case history of the successful grouting of these inflows and the continual grouting procedures in advance of present mining with empirical' results are discussed.

Jan 1, 1984

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By Yutaka Mochida

OUTLINE Beginning in 1946, a careful geological survey was made of the Tsugaru Straits. In 1964, excavation of the exploratory tunnels were started to observe the characteristics of faults and rock formation directly, and to study construction methods of excavation and sealing water inflow. In March 1971, the investigation stages were over, and in April 1971, the construction project was authorized from the government. The geological features in the straits may be divided into three broad classes. One third consists of andesite on Honshu side. The other two thirds consists of tuff. The middle of the straits consists of tuff, so-called Kuromatsunai-layers. On Hokkaido side, it consists of tuff, called as Kunnui-layers. There are nine noteworthy faults on the route. Prior to the excavation of the main tunnel, the horizontal pilot tunnels and service tunnels are made. Exploratory borings are taken to confirm the geological conditions and the presence of gushing water. Groutings for sealing water inflow are carried out when necessary. In geologically bad conditioned sections such as disintegrated or fractured zones, special methods are applied. In geologically good zones, the tunnels are bored through using the same methods as for a mountain tunnel driving. The pilot tunnel being constructed at the sea bottom is under direct control of the Japan Railway Construction Public Corporation. The service tunnel and the main tunnel are being excavated by contractors.

Jan 1, 1981

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

Soil improvement technologies have been widely employed over the recent decades to overcome tunnelling problems in difficult grounds, their range of application growing proportionally to the technological development. The constant advancement in the different mechanical (flexible and more powerful equipment) and electronic (enhanced reliability and direct quality control) aspects of these technologies, fostered the confidence of engineers and tunnellers and, ultimately, allowed the entire tunnel industry to approach difficult excavations in a safer and cost effective manner.This paper outlines the main features of commercially available soil improvement techniques, with particular emphasis on permeation grouting and jet grouting. These two technologies, developed concurrently in Europe and Japan, and there customarily adopted in the design of underground structures, have known extensive and extreme applications worldwide in recent years. Case histories and current practice of soil improvement techniques, as they apply to tunnelling, are also rendered.

Jan 1, 1999

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015