Search Documents

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By Bernhard Leist, William D. Leech, Johann Kröyer, Holger Evers

Landsvirkjun—the national electric power company of Iceland—is building the Kárahnjúkar Hydroelectric Project in eastern Iceland. Two glacial river systems will be dammed and channeled through a series of tunnels into a 690 MW underground powerhouse. The Project has a total of 73 km of tunnels to be excavated of which mosthave been completed. From three access adits, three large diameter (7.2 m to 7.6 m),main-beam, gripper-type, Tunnel Boring Machines (TBMs) are being used to complete50-km of the waterway tunnel. Using the TBMs was a first in Iceland to excavate the complex Icelandic basalt formations, which consist of inclined layers of hard basaltic flows with weaker scoriaceous and sedimentary interbeds. Faults, fissures and dykes that frequently cross the lava flows posed both geologic and hydrogeologic difficulties to the TBM tunneling. This paper describes the extreme challenges that the men and equipment had to endure to complete the tunneling, including the harsh winter weather on the surface and the cold, abundant ground water inflows within the tunnels.

Jan 1, 2007

By Gaston Gendreau, Marcel Allard

"Sidbec-Normines Inc. est une société formée de trios partenaires soient: Sidbec, British Steel Corporation et la Compagnie Minière Quebec Cartier. L'objectif de l'opération minière est d'exploiter à ciel ouvert le gisement d'hématite spéculaire de Fire Lake et de produire au concentrateur de Lac-Jeannine, près de la ville de Gagnon, 6 million de tonnes de concentré pour alimenter l'usine de bouletage de Port Cartier.Le présent exposé a pour but de fa ire ressortier les caractéristiques d'une opération dont la mine est située à plus de 100 km du concentrateur, d'en faire ressortir les particularités touchant le transport du personnel et du minerai. En plus, on traitera de l'importance dans une telle situation d'une organisation efficace dans la gestion des services et de l'opération (atelier, concasseur, entrepôt, etc.).IntroductionSidbec-Normines Inc . a entrepris l'exploitation minière du gisement de Fire Lake, le 1er janvier 1977. Le but de l'entreprise est de produire annuellement six millions (6 000 000) de tonnes de concentré d'hématite (oxide de fer) titrant 66% Fe au concentrateur de Lac-Jeannine a partir d'un minerai d'une teneur moyenne de 33% Fe, extrait de la mine de Fire Lake. Ce concentré est ensuite achemine à Port-Cartier et alimente I'usine de bouletage.Les installations minières de Sidbec-Normines sont situées a trois endroits différents : la mine à Fire Lake, le concentrateur à Lac-Jeannine et l'usine de bouletage à Port-Cartier. La mine de Fire Lake se situe à 83 km de la ville de Gagnon et à 100 km du concentrateur de Lac-Jeannine. Une route provinciale relie la ville à la mine et au concentrateur. Le minerai est acheminé de la mine au concentrateur par chemin de fer et le concentré est transporté par train sur une distance de 309 km à l'usine de bouletage de Port-Cartier."

Jan 1, 1982

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By Jacek Paraszczak

L?exploitation rentable des gisements de type filonien constitue un problème important dans le contexte actuel de l?industrie minière québécoise. Les études effectuées depuis 1994 ont indiqué, que la technologie d?abattage mécanique utilisant l?outil hydraulique appelé « éclateur radial-axial » constitue une alternative intéressante par rapport aux méthodes conventionnelles par le forage et sautage. Les essais du prototype de l?éclateur ont prouvé qu?il est en mesure d?abattre les roches dures dans un environnement minier, mais sa performance dans les termes de masse du roc abattu dans une unité de temps a soulevé certaines doutes. Pour cette raison, une étude de préfaisabilité de l?éclatage en tant qu?une technologie d?excavation souterraine a été réalisée. Cet article présente quelques résultats des travaux effectués dans le cadre du contrat octroyé à l?Université Laval par le Ministère des ressources naturelles du Québec. Leur objectif principal consistait à comparer, pour les conditions des gisements filoniens, la productivité et les coûts des méthodes d?exploitation souterraine utilisant l?éclatage par rapport à celles conventionnelles. Deux variantes proposées de cette méthode ont été comparées avec la méthode conventionnelle sur le plan du coût (par tonne de minerai) et de la teneur de coupure de minerai d'or. Les études ont démontré que l?application de l?éclatage représente un potentiel de réduire ce coût, surtout dans les situations où l?abattage sélectif pourrait avoir lieu. Pour le cas de base on a trouvé, qu?il serait possible de réduire la teneur de coupure par la marge d?environ 16 ? 26%. Toutefois, les études de sensibilité ont démontré, que le coût dépend de façon important de la productivité d?éclatage, qui, pour sa part, varie beaucoup en fonction de paramètres du massif rocheux devant être abattu.

Oct 1, 2001

By Jorge Lanza

SUMMARY La Granja copper deposit, in terms of volume, is among the five largest deposits in the world and represents reserves of three thousand million tones. The field consists of a 40 m. thick layer of copper lying over the secondary ore and further down the primary copper. The flotation process has indicated a recovery rate of 88 to 90 percent and concentrates of 27 to 32 percent of copper. The acid leaching process of low grade ore produces financially acceptable results. To carry out the project, it is necessary to build long distance pipelines and a port. Both the Feasibility Study and the Environmental Impact Study on the project have been approved by the Peruvian government. INTRODUCTION La Granja is located in the district of Querecoto, province of Chota, in the department of Cajamarca, in the Northwest of the country (Figure 1). Geographically it is situated on the eastern slopes of the Andean mountains at an altitude of 2,000 to 2,700 m.a.s.1. (Figure 1). The site is an 8 hour car ride from the city of Chiclayo, capital of the department. The first 60 km. are over a paved road and the remaining distance is over a narrow hard dirt road. The copper porphyry of La Granja was discovered between 1969 to 1971 during some geochemical prospecting activities carried out by the State mining institution, Ingeomin (currently Ingemmet). From 1978 to 1982, Ingemmet continued with its geochemical and geophysical studies supported by a German technical assistance program. A total of 19 bore- holes were drilled (5,814 m.) and a 90 m. long tunnel made. This study calculated reserves of 175 million MT. In 1993, Minero Peru drew up a technical-financial study based on the above studies and proposed a 12 year extraction operating program: 20,000 MT daily using the leaching process, followed by 13 years of operation using the flotation process with the same daily volumes. In 1994, Cambior Inc. won an international auction in order to carry on further exploration work and to have a purchasing option. Since that date the company

Jan 1, 1998

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By Jerry Dollinger, Levent Ozdemir

An extensive series of laboratory cutting tests using linear and rotary cutting machines were carried out with the objective of investigating the feasibility of achieving very high rates of penetration with TBMs in rocks of low to medium strength. These tests were performed with large diameter disc cuttrs at cutter path spacings and penetrations of up to 12 and 1.75 inches, respectively. A predictor model was also formulated to characterize rock cutting at large spacings and penetrations.

Jan 1, 1987