Search Documents

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By Tran K. Van, Francois E. Heuzé, Richard E. Goodman

Sound design of structures founded in or upon rock requires that the deformability of each rock member involved be characterized. This can be done by means of loading tests (plate bearing, flat jacks, borehole jacks, pressure chambers, etc.) or through convergence measurements (tunnel convergence, roof sag, etc.) in exploratory works. Analysis of data will be qualitative (degree of nonlinearity, creep behavior, scattering of results over a number of sites, etc.) and quantitative (modulus of elasticity or deformation). Some of these tests involve a very bulky apparatus and are expensive to perform. On the other hand, for the purpose of mapping and describing the various rock members which occur within a given site, many feet of diamond drill holes are frequently completed. Even with the optimum equipment and expert drillers, however, quantitative characterization of the rock units on the basis of tests on returned samples is apt to be misleading; the softer and weaker components of the rock tend to be lost and the fabric of the rock block- fracture system in situ is not sampled. Laboratory moduli of elasticity have proved to be consistently higher than in-situ values selected for engineering purposes. This led to the design of instruments which would operate in boreholes, combining the advantages of a reduced size and a deeper investigation, from the surface to several tens of feet. BOREHOLE DEFORMABILITY MEASURING INSTRUMENTS In the last 10 to 15 years, a number of testing devices have been con- structed which can be inserted into a borehole to apply a load and mea-

Jan 1, 1972

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

By N. E. Norman

A great deal of effort has been put forth in recent years to arrive at accurate projections of the demands for tunnels in this decade. In reviewing the statistics presented by various study groups, it appears that during the decade from 1960-69, there were some 1,335 miles of rock and soft ground construction tunnels excavated throughout the world. These statistics indicate 645 miles of rock tunnel and 689 miles of soft ground tunnel were excavated during the last decade. This is expected to increase to 3,000 miles in the 1970's according to projections made by various authorities in the field of construction tunneling. I point out the above statistics to emphasize two main points: (1) The demands for tunneling in this decade alone are staggering. (2) There is a fairly even distribution in the amount of rock tunneling and soft ground tunneling being excavated. Unfortunately, available statistics do not answer many important questions about tunneling which are of great importance to the contractor and to boring machine designers. For example, how many of the projects completed in the past decade involved both soft ground and rock tunneling? How many projects involved tunneling in conditions where both rock and soft ground were contacted at the same face. While the answers to these questions remain unanswered, I am sure most of you can think of numerous examples of projects where mixed face conditions are prevalent. Many of you are probably familiar with the Austin Crosstown Interceptor which was bid last month in Austin, Texas. Here is a project involving 57,000 feet of tunnel where limestones and clay shales are expected to be traversed. Another project, the Tonner Tunnels No. 1 and No. 2, near Los Angeles, involve some 22,000 feet of tunnel where mixed soil and rock conditions are expected. A large majority of the projected tunnels for this decade are to

Jan 1, 1997

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

By Jacques L. Mauboussin

The EUROPEAN ORGANIZATION for NUCLEAR RESEARCH (CERN) has undertaken the construction of a LARGE ELECTRON POSITRON COLLIDER (LEP), near GENEVA (Switzerland). The facility includes the main 27 km long tunnelled ring, 18 shafts, 20 experimental caverns and many auxiliary galleries. Roughly 800 000 cu.m were excavated in the molasse at 50-140 m depths, using roadheaders for caverns and auxiliary tunnels and 3 WIRTH, 4.5 m diameter, fullface TBMs for the main circular tunnel. Each TBM performs 25-30 m/day. Provisory lining behind them uses either precast concrete elements or shotcrete. Works a e being carried out by a joint-venture of European contractors led by FOUGEROLLE (France).

Jan 1, 1987

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By Eckart Schneider

PROJECT The Walgautunnel is the heart of a new hydro scheme in Western Austria, which is supposed to go into operation in 1984. With it's length of 21,4 km, a bored diameter of 6,25 m and an internal operating pressure of 13,5 bar it will be the largest water conducting tunnel in Austria. Even compared with some of the country's world-famous highway tunnels like 'Tauern' or 'Arlberg' it has to be regarded as a major tunneling project. Owner is the Vorarlberger Illwerke AG, a power corpo¬ration founded in 1924. In the course of the past 6o years this company developed the 'Werksgruppe Obere Ill - Lünersee', consisting of 6 major power plants and 4 large reservoirs. The installed capacity is 1.114 MW in the generating and 529 MW in the pumping mode. The total power output amounts to 1.916 GWh. The water for power generation comes from the glaciers of the Silvrettagroup, as this corner of the Austrian Alps between Vorarlberg , Tyrol and Switzerland is called. The Walgauwerk utilises all the water accumulated by the existing schemes as well as the so far unused run-off water, passing by in the river Ill. The intake to the Walgau-Tunnel is situated right beside the lower reservoir of the recently completed pump-storage plant 'Rodund II' at an elevation of 64o m above sea level. Though the head is a mere 162 m, 1 billion m3 of water will generate 356 GWh per annum. The power-output of the two Francis turbines is 86 MW.

Jan 1, 1983

By Cherie M. Tilley

The Stillwater Mining Co. of Nye, MT, is operating a platinum-palladium mine that requires an extensive system of footwall laterals to facilitate mine production. The 10-year mine plan calls for more than 48,300 lineal m (160,000 lineal ft) of footwall lateral. A rapid tunneling and raising system is necessary to sustain mine production schedules and achieve production goals. This article describes the results of using a Robbins 4.1-m-diam (l3.5ft-diam) tunnel boring machine (TBM) to develop the footwall laterals and a Robbins RBM-6SP raise boring machine to develop raises at the mine. The Stillwater Mining Co is a partnership between Chevron Resources Co. and Manville Corp. Chevron Resources is the managing partner. When the mine began production in September 1986, the owners were primarily concerned with the actual production of platinum and palladium, the grade minable and the amount that could be mined. As mine development and mine production proved feasible, the owners considered higher production levels. The Stillwater Mine is developed by a system of adits (known as footwall laterals) that are driven parallel to the ore bearing zone. This led mine officials to consider using a mechanical boring machine in the primary mine development. Previously, tunnel boring machines have not been used successfully in mining applications. Therefore, the owners decided to purchase a used machine to reduce the potential risk.

Jan 1, 1991

By Richard E. Gertsch

A century of experience with mechanical excavation machines is beginning to pay dividends to the mining industry. Mining is moving from mechanical excavators to mechanical miners. These mechanical mining systems are poised to make a significant impact on hard-rock mining, both underground and surface. Mechanical mining machines have had a long and successful career in coal and evaporites ("soft-rock") mining. Unlike most mechanical hard-rock mining, these systems actually mine ore. For example, the most productive underground method has been, arguably, longwall mining. Mechanical excavation machines are mostly used in civil tunneling or in driving mine openings such as vent shafts. Civil tunneling is a notable mechanical excavation success. Even with its high capital cost, a tunnel boring machine (TBM) can drive kilometers (miles) of tunnel at very low cost. In hard-rock mining, mechanical excavators bore tunnels, raises and shaft openings in the mine, but rarely mine ore. Like the soft-rock miners, their contribution to mining is important and their development must continue. Generally, they are used as excavators not miners. Current trends guarantee development of true general-purpose hard rock mechanical mining machines. Mechanical miners will become a complete mining system and will determine the design of the mine. Mechanical methods will reward the operator with lower costs and high productivity.

Jan 1, 1992

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining in usage in the mining industry. A variety of machines are now being used, including tunnel boring machines, roadheaders, continuous miners, surface miners and augers. These machines have advantages compared to drill-and-blast mining methods, including increased safety, lower cost, uniform muck size and accurately sized openings. A century of experience with mechanical methods has paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hard-rock mechanical mining machines. When several significant challenges have been met, mechanical miners will become integrated mining systems and will determine the design of mines.

Jan 1, 2002

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By E. G. Beinlich

The continuing search for faster, safer, and more economical methods of excavating underground openings has led the staff of the Mather mine of the Negaunee Mine Co. directly to mechanical boring of raises and drifts. The mine is located within the city limits of Negaunee and Ishperning in the eastern portion of the Marquette Iron Range in the Upper Peninsula of Michigan. It is owned jointly by McLouth Steel Corp., Bethlehem Steel Corp., Republic Steel Corp., and The Cleveland-Cliffs Iron Co., who also serves as the operating agent. A total of 2,400,000 tons of iron ore averaging over 60% Fe is mined annually by the block-caving method. This provides feed for the Pioneer pellet plant at Eagle Mills where 1,450,000 tons of pellets are produced yearly with the remaining tonnage being sold as coarse ore. Technical staff of Cleveland-Cliffs have long realized that improved methods of advancing raises and drifts were a necessity if underground mining of iron ore was to survive the transition period in the steel industry's requirements from direct-shipping ore to pelletized ores. For this reason, the Mather mine embarked upon an experimental raise-boring program with a prototype machine in 1961. Improvements since that time in equipment and practice have resulted in the acceptance of mechanical boring of raises as a standard development tool and a vital link in the fulfillment of an orderly development schedule. Advancement of large-diameter openings such as main-level drift headings by mechanical methods in the harder, more competent types of rock has developed more slowly in the mining industry due to the need for more compact and portable machinery and improved bit technology. Many of the obstacles have been overcome by the manufacturers, and in March 1967 it was decided to proceed with a program to bore approximately 4000 ft of 13-ft-diam drift in the Mather graywacke footwall rock.

Jan 1, 1970