Search Documents

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

The Mobile Miner MM130 (Figure 1) is designed to tunnel or mine in hard rock. It has a 4.1 m diameter cutterhead mounted on a horizontal axis which in turn is perpendicular to the line of the machine. The cutterhead rotates at 15 rpm and is supported on a boom which swings the cutterhead through a horizontal arc.

Jan 1, 1993

By Adam Saylor, Travis A. Shoemaker, Steve Miller

Lidar scanning has become an increasingly popular tool for documenting underground excavations; however, high costs of traditional mechanical electrical lidar hardware, software, and training have limited the frequency at which lidar scans can be performed. Additionally, traditional scanning can be time consuming because multiple scan positions are necessary. With Apple’s incorporation of low-cost mobile solidstate lidar on select smartphones and tablets, lidar is becoming more tractable for everyday construction documentation similar to construction photo collection with smartphones. Here, we describe benefits of mobile solid-state lidar and describe several practical applications for use in underground construction, such as documenting the working face, over-blast, and geologic features of tunnels.

Jun 13, 2023

By Junpeng L, Huiguo Q

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

Building block cave operations involves significant commitments to capital and time before arriving at completion or full scale production. The focus of the mine planners is habitually to minimize the upfront capital and achieve target development rates and construction dates. However, management of the construction of block cave projects requires understanding of the strategic/tactical decisions that the project planners can take to increase the value of the project and cope with schedule risks. As block cave projects involve development of vertical and lateral access to the underground footprint and ore body, more attention to uncertainties is required as most of those projects need to confront delays leading to a decrease in value. The standard process of development and construction scheduling is often not planned with provisions to realise uncertainties in the construction phase. Uncertainties and risks such as poor ground conditions and equipment breakdowns are the primary reasons for schedule slippage. As a result most of these projects experience delays. In order to mitigate risk to the project schedule, we centre our attention on increasing the value of the project by spending more money upfront and improving the schedule rather than focus on minimizing the upfront capital. Scenario-based simulations along with project appraisal methods hold great promise to address those challenges and enable mine planners to make better decision and enhancing project value. This paper will present a hybrid simulation based approach to model the process of development and construction based on discrete event (DES) and continuous based simulations (CBS). Such simulations will be conducted for scheduling multiple development headings (Apex, undercut, extraction, and haulage levels). Two scenarios are utilized to investigate the impact of risks on schedule and how flexibility in construction can be incorporated to minimize delays: (1) The bench mark scenario is created based on actual data from an existing case study. (2) The flexible scenario is an alternative way to use primary production infrastructure (Ore Handling System) including conveyer drifts, conveyer belt, and a gyratory crusher in the construction process and that requires the system to be in place before starting lateral development in the footprint. As a result, a truck-load system versus a conveying system will be studied to observe the gain in construction speed and to estimate the premium cost for mucking rock from headings and drawbells and transporting it to surface. Such strategic flexibility would be part of the original budget to make the tactical flexibility available during construction. Continuous cash flow models are used to evaluate and compare the scenarios. This study is an example of how new techniques in planning can be used to support decision-making processes in block cave design.

Aug 1, 2013

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By Jan K. Wolski

This paper presents a simple method for determining air temperature gradients along a tunnel with time-dependent intake air properties. The variable intake air properties may be the flow direction and rate, air temperature and humidity, and the carbon dioxide content. The transient intake air properties are simulated by a series of steady intake air conditions, using a superposition method. The mathematical model was verified by reduced-scale experiments in the Waldo mine. The method may be usefull in conditions where the computation speed is more important than the precision of the results.

Jan 1, 1995

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By Mick Lownds, Ruilin Yang

The potential advantages of electronic detonators with accurate timing have been increasingly recognized by the blasting community. However, in comparative blasts the results with pyrotechnic timing are sometimes comparable to those from electronic timing. Statistical variation in blast results is a plausible cause of these observations.

Jan 1, 2011

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018