Search Documents

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By B Rouvray, R Bertuzzi

The development of a design-and-construct tunnelling project in Australia from its concept to its construction requires designs to be prepared and reviewed at several distinct stages prior to documenting ‘for construction’. On recent projects the post-tender stages have been variously called 30 per cent—70 per cent—100 per cent; or concept–substantial–final; or system definition–preliminary–critical. The design is reviewed at each stage by the designer’s internal reviewer, the contractor and its independent advisor(s), the owner and its independent advisor(s), the project’s independent certifier, proof engineers and often third-party stakeholders and their advisors. Documentation for each stage often dominates the design effort, at times distracting from design. This paper presents the authors’ experience of this design-and-review process. Comparisons of design budget and actual design spend and design program implications are presented. It is postulated that a subtle change has occurred in our industry that has diminished the value of the design dollar. Is there a better process? An alternative is suggested.CITATION:Bertuzzi, R and Rouvray, B, 2014. Reducing the cost of tunnel design in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 501–506 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By P. Horrell, K. Rhodes, G. Harrison, J. Dean, D. Sammons, M. Stander

Anglo Platinum have perceived a need to increase the rate of reef development both for new mechanised stoping technology and on conventional new developing mines. The Research and Development Division of Anglo Platinum therefore initiated an experimental reef raise project with a tunnel boring machine (TBM) at Bafokeng Rasimone Platinum Mine (BRPM). The scope of the trial was for the boring of a reef raise 340 metres in length on the Merensky Reef. The boring phase of the trial took place over six months and the average rate of penetration of the TBM was 0,47 metres/hour. TBM utilisation was 22%. The TBM used in the trial was a Jarva MK6 manufactured in 1972 and its design with its backup system was not considered to be an ideal machine for reef development. However it was the intention of the trial to prove the concept of developing with a TBM on reef. In this respect the trial was unequivocally a success. There were many problems and long delays did occur during the boring phase. Nevertheless there is every confidence that a new TBM can be designed specifically for this type of work that will achieve high rates of advance up to (say) 400metres/month and with a more flexible steering system in order to negotiate reef changes. It can therefore be expected that TBMs will be used in the future for reef development on South African platinum mines.

Sep 1, 2001

"IntroductionThe combined library facilities of the five universities in the Generic Technology Center for Respirable Dust, The Pennsylvania State University, West Virginia University, University of Minnesota, Massachusetts Institute of Technology, and Michigan Technological University, represent one of the most extensive and comprehensive collections of information on respirable dust research which is available in the United States. The Center encompasses two major medical schools, the Milton S. Hershey Medical Center at The Pennsylvania State University and .West Virginia University Hospital at West Virginia University, and includes national and international experts from such diverse disciplines as geology, geomechanics, mining engineering, mineral processing, electrical engineering, industrial engineering, mechanical engineering, material science, physics and several areas of medicine. In order to maximize achievements in research and facilitate early results application in the private industry, university, government and public sectors, a geographically dispersed Reference Center on Respirable Dust has been established at each of the affiliated universities. This network serves to encourage unity between the universities in the Center and coordination and communication with other entities who benefit from their research.Description of the Reference CenterIn this light, the goal of the Reference Center network is to identify at what location Information is available and to provide a means for others to access this information. It is especially necessary to have both ease of input and maximum retrieval capabilities available to all the research personnel in the Reference Center. At the same time, the service provided to the inquiring public must be complete and cost-effective. The Center's approach to realizing this goal incorporates advances in computerized and electronic searching of individual library holdings and the networking of major library and commercial search systems.The Reference Center uses the following means to achieve this goal. At each participating university, a hard copy collection ls maintained of the current respirable dust research in progress by that institution's personnel. Also, available. at each university ls a review of their past and present research on respirable dust. At each participating university a hard copy collection of annual status reports and of all publications produced by Center personnel for symposiums, national and international conferences ls maintained. A key word computer search capability ls available to participating universities. This computer search, by title, author and location, allows researchers to determine at which facility information is available, thus avoiding the tremendous expense and effort of housing all the information on respirable dust research under one roof. The Reference Center has access, through The Pennsylvania State University Libraries system and the libraries of other institutions, to a large number of data bases such as MEDLINE at the National Library of Medicine,"

Aug 31, 1989

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep hardrock mines worldwide increasingly face rockbursts as mining depths increase. These events result from the accumulation and sudden release of stress, causing rockmass damage and posing major safety and operational challenges. This paper focuses on destress blasting as a critical strategy to mitigate rockburst hazards. Although limited practical experience exists in Swedish deep hardrock mines, international case studies demonstrate that, when well implemented, destress blasting redistributes peak stresses by promoting controlled fracturing around mining excavations. The success of such techniques is highly dependent on site-specific factors such as stress regime, rockmass brittleness, structural geology, and blast layout. Although destress blasting is especially effective in massive, brittle rock under high stress, typical conditions for strainburst prone environments, its design cannot rely solely on numerical models. Simulations can offer preliminary evaluation of stress redistribution trends and guide early design assessments but their current limitations, including sensitivity to input data and simplified fracture mechanics, mean they are best used as supplementary tools rather than final decision-makers. Field trials, supported by microseismic analysis and fracture mapping, remain essential for validation. The study critically synthesises international experiences and presents a structured framework for destress blasting design, offering practical and academic perspectives aligned with Swedish geological conditions to support safer and more efficient application in deep hardrock mines.

Jun 27, 2025

By F T. Suorineni

Empirical methods are deeply rooted in geomechanics. This is a consequence of the recognised complexity of the nature of the rock mass. The usual assumptions of material continuity, homogeneity, isotropicity and linear elasticity often assumed for soil, concrete and steel are difficult to justify in a rock mass except for mathematical convenience. These assumptions form the bases for most mechanistic, analytical and numerical methods in geomechanics. Believers in empirical methods argue that the complexity of the rock mass and its interaction with structures developed in it is adequately accounted for in empirical methods, which compensate for our ignorance.Franklin (1993) defines empirical design as quantified judgement based on experience. He further states that empirical methods often prove ‘closer’ to the ‘truth’ than the apparently more precise predictions of theoretical analysis, adding that based on real data empirical methods provide a standard against which theoretical predictions are measured and can be judged. This paper takes a critical look at the common empirical methods in geomechanics – rock mass classification systems (Bieniawski, 1973; Barton, Lien and Lunde, 1974; Hoek, 1994a), Laubscher block caving design rules (Laubscher, 1994), the stability graph (Mathews et al, 1981), pillar design equations (Salamon and Munro, 1967; Hedley and Grant, 1972; and their derivatives), pillar design chart (Lunder and Pakalnis, 1997) and failure criteria (Hoek and Brown, 1980; and its derivatives). The common thread in the application of these methods is that in most cases they are often applied blindly without an understanding of the underlying assumptions and database limits. This paper emphasises that users of these methods need to know the underlying assumptions, database limits and inherent hidden risks that are often unmentionable for their satisfactory use. Finally, suggestions are provided for the efficient use of empirical methods and how they can be improved.CITATION:Suorineni, F T, 2014. Reflections on empirical methods in geomechanics – the unmentionables and hidden risks, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 143–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017

By P wade

This is the first Presidential Address given to the Nottinghamshire Branch of The Institution following the merger of the Nottinghamshire and North Derbyshire Branch of The Institution of Mining Engineers (IMinE) and the Midland Branch of The Institution of Mining Electrical and Mining Mechanical Engineers (IMEMME). I intend to review the formation of the individual institutions as well as what has been achieved by mining related institutions over the years and finally I intend to look to our future.

Jan 11, 1996

By HAROLD E. WHITE

LONG before the Stone Age, when man first sought shelter where there-were no natural shelters, such as caves and clefts in the rock, he uprooted trees and planted them upside down so that the roots formed the roof. By selecting trees whose roots grew out in a horizontal direction and; by planting these trees close enough - together, a crude shelter was formed. He then took mud, formed a plaster and covered over the' roots. Later the walls were made by using sticks and twigs and plastering between them. It is natural then, that he wiped his muddy hands on- his own hairy body and soon found that the mud was difficult to remove when, dry. It is due, to this discovery that we mix animal hair in 'our modern plaster to increase its strength. The use of fibrous asbestos in some refractory cements has followed this same principle.

Jan 1, 1929

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933