Search Documents

By R. W. Van Dolah, N. E. Hanna, F. C. Gibson

Measures that were taken to eliminate noise resulting from explosives work at the Bureau of Mines facility at Bruceton , Pa . , are described . A method for monitoring sound transmission characteristics of the atmosphere and control of the explosives testing is presented as a noise control measure that offered partial relief during the period in which the modifications were made . Design details of the replacement gallery , used for permissibility testing of explosives , and the modifications of four types of bombproofs are given . Operation of the closed facilities are completely satisfactory , and the noise problem has been entirely eliminated .

Jan 1, 1964

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By T. F. Curry, L. B. Berger, H. A. Watson, S. J. Pearce

The conduct of work at elevated air pressures , such as in caissons and in tunnel - driving in subaqueous strata , poses safety problems not encountered in mining and tunneling operations at ordinary atmospheric pressure . This publication discusses some of the problems involved and presents information on the following subjects : ( 1 ) Physiological effects of gases at elevated pressure . ( 2 ) Use of respiratory protective equipment in rescue or recovery operations in event of fire or other emergency in pressurized tunnels . ( 3 ) Effect of elevated pressure on performance of some gasdetecting instruments ; interpretation of the results . Various types of respiratory protective devices are discussed in relation to their possible use at elevated pressures , especially the 2 - hour , selfcontained , recirculating - oxygen - breathing apparatus , which has had wide use in the United States during rescue and recovery work in the mining industry . A modified procedure that eliminates the hazard of oxygen poisoning enabling the safe use of this apparatus at elevated pressures , up to 45 pounds per square inch , gage , and tests to verify its practicability are described . procedure involves control of the partial pressure of oxygen in the breathing

Jan 1, 1964

By David W. Wisecarver

This report describes a tool to engage and/or place a Bureau of Mines type gage to measure borehole deformation in a horizontal , 1½ - inch - diameter , stress relief borehole . The tool was successfully used at a borehole depth of 105 feet . Practical usage up to borehole depths of 200 feet might be realized . The tool was designed to work inside EX- size ( 1½ - inch ID ) diamond - drill drive casing used as drill rod and through which the deformation gage is guided into an EX- size stress relief borehole . Through laboratory experiments it was found that by exercising a reasonable amount of care the deformation gage could be placed at a point within a ± .01 foot distance of a predetermined depth in a horizontal EX- size hole and that the deformation measuring piston or plunger of the gage could be oriented in the borehole within 0.5 ° of a preselected angle of orientation in a vertical plane .

Jan 1, 1964

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By John Nagy

Dust explosion data obtained in laboratory studies by the Bureau of Mines are presented for activated carbon, asphalt, charcoal, carbon black, coal, coke, gilsonite, graphite, lignite, miscellaneous carbons, pitch, tunnel dust, and mixtures of these materials with other ingredients. The explosion hazard is shown to increase as the volatile content of the dusts increases.

Jan 1, 1965

By C. C. Popoff

This report reviews the phosphate deposits, mines, and industry, and prospects in 10 districts covering most of the Montana phosphate field. These districts are discussed individually, and an evaluation of the resources and potential of each is presented. Phosphate rock produced from underground mines in the Garrison district is shipped to Canada for processing to fertilizers, utilized locally for production of animal feed supplement, and pulverized and sold for direct application to the soil. Production from the Melrose district is shipped to Silver Bow and processed to elemental phosphorus. The Maxville-Philipsburg district is destined to become a major producer with the development of the Douglas Creek mine and beneficiation plant by Montana Phosphate Products Co. Montana ranks fourth after Florida, Tennessee, and Idaho in total annual production in the United States. Production him increased from about 60,000 long tons of acid-grade phosphate rock in 1940 to more than 660,000 tons of acid-, beneficiation-, and furnace-grade ore in 1961. Montana has the second largest potential resources in the Western field; in the area south of Butte there are approximately 1.2 billion tons of phosphate rock (+18 to +31 pct P2O5) available above and within 100 feet below entry level; and in the northern part of the field there are about 67.6 million tons available above entry level. In contrast to Idaho, most of the phosphate deposits in Montana are best suited to underground mining.

Jan 1, 1965

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965

By Raymond L. Lowrie

Coal deposits in the Boulder-Weld County coalfield in Colorado are analyzed in relation to economic factors governing the growth, stability, and competitive potential of the coal industry. Recoverable reserves, estimated to be 571 million tons, are discussed in detail, particularly those in the Erie and Frederick Quadrangles. Geology of the coal measures, quantity and quality of water resources, and chemical and physical properties of the coal are described. Coal production factors, including mining techniques and equipment, labor requirements, transportation facilities and rates, and markets, are considered for coal's position in competition with alternate fuels. Growth of the fuels market, through increasing thermal-electric power generation in the Denver Metropolitan Area, will stimulate coal production in Colorado. Reserves of the contiguous Boulder-Weld coalfield, if mined in a sustained, year-round, high-tonnage operation, could be used to supply much of that fuel demand.

Jan 1, 1966

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1966

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966