Search Documents

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By P. D. Kovscek

The performance of a novel prototype kerf-cutting impact mining machine was evaluated under a cooperative agreement between the U.S. Bureau of Mines and RAMEX Systems, Bellevue, WA, while operating under conditions typical of normal tunnel entry development. Selected operating parameters were monitored concurrently to determine baseline operating conditions and to study relationships between operating parameters. Using the data obtained, the specific energy requirements of the impact mining machine were calculated and compared to specific energy requirements of tunnel boring machines cutting in rock having similar hardness. Tests results indicate that the kerf-cutting impact mining machine can provide a mechanical means for mining very hard rock that cannot be effectively mined using commercially available mechanical excavators.

Jan 1, 2010

By Charles D. Litton

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By Noel N. Moebs

This report summarizes a U.S. Bureau of Mines study on the application of geotechnology to identify and minimize ground control hazards in talc mining operations in northwest Georgia. The major ground control hazard is pillar sloughing attributed to the steeply dipping orientation of a pronounced foliation in the talc ore body. The sloughing problem, which gradually reduces the effective support area of a pillar through attrition, can be minimized by appropriate artificial support, as determined by a rock classification system, and by a more uniform pillar design. A boundary element model confirmed the advantages of using a uniform pillar design to avoid excessive loads on portions of irregular pillars. Instrumentation to measure roof convergence and pillar loading was installed at selected locations in an active talc mine but failed to detect any significant changes, suggesting that the gneiss hanging wall constitutes a strong roof that probably can support large spans between pillars and permit high extraction ratios. This interpretation also is supported by a rock classification of the hanging wall gneiss.

Jan 1, 2010

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the water spray patterns of automatic sprinkler heads. Experiments were performed in a rectangular tunnel with pendent, upright, pendent sidewall, and horizontal sidewall sprinkler heads at air velocities of 0, 150, 300, 500, and 800 ft/min. As the air velocities were increased, there were significant shifts in the total coverage areas, density distribution patterns, and the maximum coverage densities for all types of heads. The pendent and upright heads exhibited upstream shifts in total coverage in the direction of the air-flow ranging from 4 to 6 ft, while the downstream coverage distances were extended up to 14 ft at the 800 ft/min airflow. The shift in upstream coverage distance for the sidewall heads ranged from 6 to 12 ft, while the downstream coverage was extended up to 22 ft at 800 ft/min. The results showed that airflow can have a significant effect on the coverage characteristics of automatic sprinkler heads and needs to be considered in the design of effective sprinkler fire suppression systems for ventilated areas.

Jan 1, 2010

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By William W. Aljoe

The hydrologic characteristics of two abandoned underground coal mine sites, near Latrobe, PA, and Uniontown, PA, were investigated by the U.S. Bureau of Mines for possible implementation of alkaline injection into the mine pools as a means of abating their acid discharges. The Latrobe site was chosen for a one-time application of alkaline injection to achieve a partial, short-term neutralization of a limited portion of the mine pool. A quantity of alkaline reagent (sodium hydroxide) sufficient for a one-time neutralization of the water in this portion of the pool was added. Although nearly all of the neutralizing reagent had moved away from the injection wells within 6 weeks, no evidence of neutralization was noted at the mine discharge during the study period. This lack of neutralization probably occurred because the injection wells did not intercept a primary flow path through the mine. Criteria for successful application of alkaline injection at this or other sites include (1) positive identification of the primary flow paths through the mine pool and (2) addition of quantities of alkaline reagent sufficient to neutralize the entire volume of the pool along the primary flow path.

Jan 1, 2010

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By Robert C. Dyni

The use of techniques and equipment designed to pneumatically place backfill into an underground mine opening through boreholes for subsidence abatement has historically met with limited success, largely due to the inability to directly monitor the placement of the backfill in the opening. The success of a backfilling project cannot be guaranteed if it is not known whether the underground opening has been completely filled with backfill material. To overcome the inability to directly monitor backfill placement, the U.S. Bureau of Mines developed a pneumatic backfilling system that allows for direct viewing of the backfill as it is placed in an underground mine opening. This system utilizes a recently developed pneumatic nozzle coupled with an instrumentation package that allows for real-time observations and measurements of backfill placed in an underground opening through a borehole. The nozzle utilizes a high-velocity airstream to redirect backfill falling through a pipe in the borehole and directly in front of the nozzle; the airstream redirects and propels the backfill horizontally into the .mine opening at over 100 ft/s. The instrumentation package, mounted directly to the nozzle, contains a video camera, high-intensity lamps, laser-rangefinder, electronic compass, and water sensor.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010