Search Documents

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By John V. Beall

With some difficulty we framed the picture of the village on the mountain getting in the railroad bridge and tunnel at the base. It was a charming scene of red-tile roofs on a green mountain in the golden autumn sunshine with the black hole of the railroad tunnel looking like something out of the movie, "The Train." We clicked the shutter, advanced the film and started back to our rented Audi. At which point there was a hail from the other side of the railroad bridge. A man in uniform was brandishing an object in the air which looked suspiciously like a rifle. We peered around. We were the only other persons in view. He must be yelling at us. He was now closing the distance at a brisk, determined gait but was still 100 yards away. The car was handy but the road was straight, paralleling the railroad tracks for some distance. We dismissed the idea of running for it. Who knows, he might shoot. When he came up we didn't have much of a conversation because it had taken us a week to learn three words of Yugoslavian-zhiveli, long life, huhvalla, thank you, and schlivavitza, the national drink (plum brandy). None of these seemed appropriate. We got the Idea that photographs of railroad tunnels and bridges were prohibited. The guard, for such he seemed to be, took the Audi plate number, administered a last scowling reprimand and stalked off. This incident was the only one in a 15-day visit to Yugoslavia which we would have associated with "Iron Curtain restrictions."

Jan 1, 1970

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geo- physics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining.

Jan 1, 1949

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By Sangseom Jeong, Kyoungyul Kim, Jaeyeon Cho

"Abstract The lateral earth pressure of vertical circular shaft is investigated by using experimental tests and a theoretical analysis. The emphasis was quantifying on the magnitude and distribution of a lateral earth pressure measured by three-dimensional arching effect. A framework for determining the earth pressure distribution on the basis of both centrifuge model and full-scale field test results is introduced. Through these studies, it is found that the lateral earth pressure decreases within active displacement (dh/H: 0.2×10-2, dh: horizontal displacement, H: Height of vertical shaft) of wall at deep excavation and the arching effect is more significant for deep excavation than for shallow excavation. It is also found that the lateral earth pressure acting on a vertical circular shaft considering arching effect is 70% smaller than that calculated by Rankine theory, and thus represents a significant improvement in the prediction of realistic earth pressure for vertical circular shaft subjected to arching pressure.INTRODUCTIONIn South Korea, an increasing need for underground excavation and the application of the vertical circular wall (i.e. vertical shaft) is becoming an important issue in engineering practice. Here the vertical circular wall is generally embedded in soft or hard rocks through weathered soil varying thicknesses ranging up to 15 m. Since 1980, a number of huge excavation projects such as underground space for constructing power stations, subways, high-speed railways, and many lifeline constructions have been performed in urban areas (Jeong and Seo, 2004). Although there have been considerable advancements in construction techniques involving vertical circular wall, it is still very important for tunnel engineers to control the lateral earth pressure. Additionally, Proper estimation of earth pressures is a key factor in design of vertical circular wall. Because of three dimensional arching effects, i.e. convex arching and/or inverted arching, the earth pressure acting on a circular type of wall is less than other types. Thus, the vertical circular wall is generally used."

Jan 1, 2014

By Nikzad Oraee, Parham Khajehpour, Kazam Oraee, Arash Goodarzi

"Rock fall related accidents continue to occur in coal mines, although artificial support mechanisms have been used extensively [1]. Roof stability is primarily determined in many underground mines by a limited number of methods that often resort to subjective criteria. It is argued in this paper that stability conditions of mine roof strata, as a key factor in coal mines, must be determined by a survey which proactively investigates fundamental aspects.Failure of rock around the opening happens as a result of both high rock stress conditions and the presence of structural discontinuities. The properties of such discontinuities affect the engineering behavior of rock masses causing wedges or blocks to fall from the roof or slide out of the walls [2]. A practical rule based approach to assess the risk of a roof fall is proposed in the paper. The method is based on the analysis of structural data and the geometry and stability of wedges in underground coal mines. In this regard, an accident causing a huge collapse in a coal mine leading to four fatalities is illustrated by way of a case study. A comprehensive investigation of the hanging wall has been gathered through a systematic collection of evidence. The investigation results are then analyzed, and an interpretation of the evidence gathered is provided.For this purpose, horizontal and vertical profiles are prepared by geophysical methods to define the falling zone and its boundaries. The collapse is then modeled by the use of sophisticated computer programs in order to identify the causes of the accident and hence recommend corrective actions to prevent or minimize reoccurrence probability of similar accidents. The corrective measures are placed into a rule-based framework for the benefit of the mine operators.INTRODUCTIONRoof rock failure has generally been the most dangerous hazard for underground coal mining in the world. Failure of rock around shallow coal mine openings often results from loosening of blocks of rock on the weakened planes under the influence of gravity. This condition is not typically seen in large deep coal mines. There are a number of differences between large mechanized mines and small mines related to ground control [3]."

Jan 1, 2015

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.