Search Documents

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth's surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By E Mutaz, M Bahaaddini, D J. Williams, M Serati

The contribution of the mining industry to the global economy has reached (and gone beyond) $1,800 billion in recent years that necessitates (more than before) the need to ensure workability, viability, health, and safety of mine sites and workers to meet the ever-increasing global demand for mineral resources. Amongst the many challenges facing the excavation industries, rockburst and spalling failures in deep mines in hard and brittle rock formations are yet happening that are still deemed as unsolved problems. During unconfined compressive testing of brittle rocks, microcracks initiate at approximately 0.3–0.5 of the peak strength (which is commonly known as the Crack Initiation stress level) mainly in the direction of the major principal stress, then grow unstably and coalesce to form macro fractures at approximately 0.7–0.8 of the peak load at a so-called Crack Damage stress threshold. From a stress-strain perspective, the crack damage stress threshold () is associated with the reversal point of the volumetric strain, which is also proved to be strongly affected by the intermediate principal stress. This paper extends the previous studies on the impact of true triaxial loading conditions on the CD stress level in high porosity rocks, and introduce a new Crack Mode-Changing Stress (CMCS) defined as the minimum principal stress required to change rock fracturing from splitting to a sliding failure mode. A large number of experiments on sandstone specimens were carried out at different true triaxial loading conditions and the effect of principal stresses on the CI and CD as well as CMCS were studied. The results show that not only the intermediate principal stress, but also the minor principal stress can significantly affect the CD and CMCS thresholds.

Apr 26, 2022

By J. W. Mahar, E. J. Cording

INTRODUCTION In exploration for rock tunnels, the geology should not only be described, but its effect on excavation and support assessed. It is not an easy task to correlate exploration results with support and excavation requirements, even when the exploration program is detailed and geologic conditions are relatively well known. Many of the significant geologic features are subtle and their effect is difficult to interpret from exploration results. However, in similar geologic settings, there are specific geologic features which will cause recurring support problems. Such features should be actively sought out when exploring in a given geologic setting. In blocky and seamy rock, the primary features controlling performance are the joints, shears, and shear zones. This paper describes the effect of such features on the formation and movement of rock wedges in tunnels driven in foliated metamorphic rocks in Washington, D. C. and New York City. In both areas the foliation commonly forms a N-S striking plane of weakness along which major shear zones, shears, and joints have formed. In addition, the structural history of the two areas has been similar, so that there are similarities in the orientation and character of the other major joint sets and shear zones in the rock mass. The observations were made in tunnels ranging from 10 to 70 ft in width and excavated at depths ranging from 80 to 800 ft. Most of the tunnels described were deep enough to be located in unweathered rock, or in rock only slightly weathered along joints and shears. Variations in the planarity, filling, spacing, and attitude of joints, shears, and shear zones accounted for significant differences in the

Jan 1, 1974

By Tadashi Nishida

Subsidence due to mining caused various kinds of damage to the surface structures, and actually great deal of mining damage becomes the severe social problem at some time in many coal fields, but the most of mining damage was restored at present. Recently, the effect of old coal working on the deformation of newly constructed structures has become into question, because it was obliged to plan many engineering structures in old mining areas for the shortage of adequate construction sites and the difficulty of getting location. That is, building, dams, bridges for railroads and highway, power plants, tunnels, storage tanks and so, have to be built on the ground which has old coal working.

Jan 1, 1982

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By Sunil Vytla, Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes (carbon monoxide and nitrogen dioxide) clearance and workplace reentry time have overlooked the effects of toxic gases trapped in the muck pile. The currently available models for calculating the mine reentry times assume that all post-blast fumes are emitted upon detonation. However, recent studies reported that as much as 60 to 70% [1–5] of the fumes or gases produced during an underground development blasting could remain trapped in the adjacent rock mass or in the muck pile. Trapped fumes are slowly released [1–5], and when disturbed, high concentrations are released, representing a possible risk during the loading and transportation of the muck pile. In this study, mathematical models were developed using computational fluid dynamics to understand the behavior of the trapped fumes and their effect on mine reentry time. The three scenarios considered for this study include (i) gas emission source with no muck pile volume, (ii) gas emission source with non-porous muck pile volume, and (iii) gas emission source with porous muck pile volume. The estimated reentry times in all three scenarios were compared to see how porous media affects dilution time. It was observed that scenario 3, with fumes trapped in the muck pile, took a significantly longer clearance time (more than double) as compared to scenarios 1 and 2.

May 17, 2022

By Liu Hui Yang Nianhua Feng Shuyu

The paper analyzed the dynamic stress in the rock around the tunnel and the effect on the stress variation for the different blasting parameters. Also, the paper verified the theoretical results by dynamic photoelastical tests and provided helpful reference for the design of blasting near a tunnel.

Jan 1, 1998

By S. Balideh

A good understanding of the behavior of broken rock helps to make more informed decisions regarding slope stability and waste dump issues in mines. The cohesion coefficient of rock has little influence on the strength of broken rock; therefore, a criterion based on friction and cohesion of intact materials does not provide an accurate analysis for the strength of broken rock. This paper illustrates the effective strength of broken rock through a brief literature review about failure of intact rock and rock masses. The complete stress- strain curve and some important points of residual strength of rock are summarized in this paper.

Jun 1, 2012

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By A. Cobbii, M. Kasliki, W. Birchi

The Department of Mining and Mineral Engineering at the University of Leeds has a long history of research into the environmental impacts of blasting from quarries and opencast mines. This paper gives an outline of a detailed case study into the structural damaged induced in a rock walled tunnel with a brick lined crown due to close proximity quarry blasting. The test site Taffs Well Quarry is located in South Wales in The United Kingdom and has a disused railway tunnel situated within the south eastern comer of the quarry site. Quarry development plans included the working of this area and therefore the deliberate destruction of the central section of the tunnel.

Jan 1, 2001

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019