Search Documents

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By Michael Schultz, Gregory Sanders

The City of New Haven is planning to construct the Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 685 cubic feet per second (cfs) stormwater pump station and a 3,200 linear feet (975 meter) long tunnel segment with an internal diameter of 120-inches (3.05 meters). This paper presents the aspects of the final design and the use of the cloud-based data management software to make better data-informed decisions. The software was used to create a spatially aware database of the subsurface conditions, as well as improve visualization and analysis of the soil properties.

Dec 1, 2022

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993

By R Farnf, M Pegden, S Hosein, T White

A number of theoretical papers have been published outlining the use of electronic detonators to limit peak particle vibrations levels, but few empirical studies have been undertaken and even fewer examples have been published of the use of such technology in the aggregates industry. This paper gives a summary of the research work carried out at two limestone quarries in the North of England, where a series of blasts were used to compare and contrast the use of electronic and non-electric detonators. The majority of blasts were carried out using the same burden, spacing and decked charge weight loadings. A methodology was established that could be used to reduce the peak particle velocities (PPVs) at two or more specific locations by using single-hole blast vibration signatures in conjunction with specific electronic detonator timing intervals. The initial study concluded that this was only possible if single-hole signature blasts were periodically recorded to establish the shape of the correct vibration envelopes as properties were approached. These wave envelopes could then be used as the basis for choosing the specific electronic detonator timing intervals to give the lowest PPV for the properties or locations concerned. This methodology was then used in the second study to access a large volume of aggregates adjacent to a working railway tunnel. The financial benefit for the company was to convert these additional tonnages of rock from being a resource to an exploitable reserve. The project involved careful blast design and the instrumentation of a number of boreholes to enable the results of blast monitoring exercises to be compared with predicted PPV results. The iterative process involved the vibration results being uploaded into æBlast LogÆ (an expert blasting database system developed by the Blasting and Environmental Research Group at the University of Leeds) and analysed to produce predictions ready for the next blast.

Jan 1, 2007

By C. Yoo

"Geosynthetics engineering has made phenomenal advances during the last decade in areas of manufacturing as well as practical applications. As a result, geosynthetics are now being recognized as essential construction materials that can be used to facilitate construction, ensure better performance of the structures and reduce the long-term maintenance in routine civil engineering works. The creative use of geosynthetics in geo-engineering practice is expected to continuously expand as innovative materials and products are becoming available. In this paper, a wide variety of geosynthetic products available to geoengineers to solve a wide range of problems are briefly presented along with their functions and possible applications. Fundamentals of geotextile filter design principles are then introduced for use in the tunnel drainage system. Practical applications of geosynthetics relevant for tunnel engineering are also highlighted with emphasis on the issues associated with the geotextile filter application for use in the tunnel drainage system.INTRODUCTIONGeosynthetics have emerged as essential engineering materials in a wide range of civil engineering applications, e.g., transportation, geotechnical, geoenvironmental, hydraulics, and private development since the first geosynthetic conference in Paris, 1977 (Koerner 2012). Due to their costeffectiveness, ease of installation, and well established mechanical and hydraulic properties, geosynthetics are now playing important roles in the field of geo-engineering.As indicated in the 9th Bucahanan Lecture paper by Holtz (2001), major developments in civil engineering have only been possible with the parallel developments in the technology of construction materials. For example, larger scale structures became possible with the help of developments in concrete, reinforced concrete, and prestressed reinforced concrete technology which replaced wood and building stone as construction materials. The best example of a parallel development in geo-engineering between the material and the geotechnical application may perhaps be the soil reinforcement technology which has a direct analogy with reinforced concrete as a polymeric reinforcement material provides added level of tensile resistance and stability to soils that have little to no tensile strength, thus giving additional margin of safety."

Jan 1, 2015

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By D P. Proudfoot, S G. Keith, D P. Onagi

A number of aspects of the Canadian concept for nuclear fuel waste disposal are being assessed by Atomic Energy of Canada Limited (AECL) in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, Canada. One of the major objectives of the work being carried out at the URL is to develop and evaluate the methods and technology to ensure safe, permanent disposal of Canada's nuclear fuel waste.

Jan 1, 1996

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Bruce Notthup

Using a Three Dimensional Laser Profiler, persomrel from Austin Powder were able to determine drilling patterns for use in underground mine Room and Pillar blasting operations, The faces had got out of alignment, causing concave faces across the 100 feet wide, 28 feet high tunnels. This was leading to poor drilling and poor blasting results. By profiling the faces, modifications could be made to the drilling pattern to help gradually straighten the faces. The Laser Profiler was also used to check the accuracy of collaring the holes and also perform post blast surveying of the positions of the bootlegs. This allowed recommendations to be made to improve drilling operations at the face. In addition, other volumetric calculations could be performed using the systems’ surveying software, all a lot more easily and quickly than by standard methods.

Jan 1, 1994

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By B Jones, M Chappell

Permanent rock bolts used to support rock tunnels are required to perform for the design life of the structure as a minimum. Quality of installation is critical to the performance over the life of the rock bolt.This paper will present the findings from an in investigation into the integrity of rock bolts installed in an underground hydroelectric power station cavern and access tunnel. The 25?mm diameter rock bolts were installed 50 years ago, tensioned and post cement grouted. Due to a major machine upgrade the whole facility was subject to an asset survey. The owners are responsible for managing the risks associated with the failure of these rock bolts and ensuring the structural integrity of the tunnels and caverns is maintained to continue operations, protect machinery, assure production and more importantly maintain a safe working environment for all employees and visitors.To help manage risk a proactive approach is desired. To this end a test schedule using a non-destructive testing (NDT) system was carried out by Independent Integrity Testing Pty Ltd (i2t). The system used in this application was RokTel™. The system operates by applying a small axial impact to the rock bolt end and measuring the resultant acceleration response. The rock bolt characteristics affect the acceleration response.The data output from the system is analysed principally using Fourier Analysis (FFT) and sinusoidal waves. The energy generated in the bar, the rate of damping and changes in frequency are all assessed. Testing was carried out on 70 rock bolts within the tunnel and cavern. A selection were then over cored, photographed and documented. The data gathered from the testing is then correlated with physical evidence to establish a calibration for the remainder of the rock bolts and assess if this is a viable method for identifying defective elements, and what degree of accuracy can be achieved. The findings will assist with the future assessment of similar hard rock underground?facilities.CITATION:Jones, B and Chappell, M, 2014. The use of non-destructive testing to identify defective rock bolts – a case study, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By H. E. Grier, H. H. Aronson, H. F. Coffer

"Nuclear explosions are currently being planned for use in oil and gas production, the recovery of oil from oil shale, gas storage and copper leaching. The current status of each of these projects is discussed, with emphasis on the economics of each application. The first commercial application of nuclear explosives will be in gas stimulation. Project Gasbuggy will be rapidly followed by two additional shots, also related to gas production. These three events, each in a different formation, will be described in this paper with a discussion on their significance to the world's oil and gas industry. The use of nuclear explosives in oil and gas stimulation should be a standard accepted practice within a few years. Calculations based on explosions in media such as tuff, alluvium, granite and dolomite predict large increases in productivity when nuclear devices are used in tight, thick formations. The broken-up rock resulting from the explosion becomes the new well bore, with a production rate of six to twelve times that of a normally completed well.Also included in the paper is a discussion of the real or possible problems associated with nuclear explosive engineering. The only major foreseeable problem is the seismic shock wave. This limits the size of explosive which can be used near important surface structures. A discussion is included on the radiation problem, which we believe to be largely psychological in the case of contained explosions."

Jan 1, 1968

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

By Peter J. Borchardt, Helen M. K. Andersson, Donald A. Bruce

Grouting is a useful engineering tool for tunnels throughout the world. A wide variety of methods and materials are used, reflecting the broad range of geological, hydrogeological, and structural demands. Most tunnel grouting is conducted with cement, which produces acceptable results in appropriate conditions. However, there are cases where such grouts are not practical, but polyurethane grouts can be extremely useful. Regretfully, these grouts are frequently poorly understood, leading to improper application and therefore poor results. This paper provides a fundamental overview of their application, both used individually and in combination with cement. Case histories from Scandinavian practice are cited.

Jan 1, 2001

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

According to the Australian Bureau of Statistics, fatalities from road transport accidents represented an average of over 97 per cent of all transport related accidents between 1997 and 2002. With increasing traffic density, tunnels are becoming a more viable means of providing alternative travel routes to ease areas of congestion in the road transport network. However, unlike open road conditions, a fire incident in the confined space of a tunnel environment may impact upon many users that are remote from the incident location. In this context, designing for an appropriate level of safety in tunnels is therefore an important consideration for achieving consistency in the life safety measures for users of the road transport network. Unfortunately, like fire safety engineering design for buildings, there are presently no clear measures in the design processes to assess the adequacy of the design in terms of attaining the level of safety implicated in the design objectives. This is partly due to the indeterminate nature in which the design objective or the level of performance measure is stated û the intent of the objective is relatively clear but the measure of it is not. Another reason is the lack of a standardised procedure for determining the critical design variables affecting life safety. This is important to ascertain consistency in the use or adoption of the important parameters for design. This paper looks at the processes involved in the fire engineering design of road tunnels that are currently practised. A review of the design processes for fire safety in road tunnels is provided, which includes the range of fire scenarios in a tunnel environment, the traffic flow and composition, the relevant fire protection systems, the ventilation and smoke control system, the egress provisions and the benefits of incorporating fire brigade intervention. A simplified risk assessment approach is developed for a typical road tunnel to assess and evaluate the impact of a range of design parameters on life safety. Using a sensitivity technique, the important variables are then identified and means of reducing design variations associated with them are recommended. The technique may be further refined for use in the development of codes or guidelines in order to develop a suitable means of deriving more consistent design values, and hence achieve better consistency in the overall level of safety in the design.

Jan 1, 2008