Search Documents

By Jeff Hammer, John McGregor

"The Twin Tunnels, originally constructed in 1964, have become a major choking point for trafficheading up to and returning from the Colorado high country along the I-70 corridor. To increase traffic flow, the Colorado Department of Transportation undertook the first widening of the East Bound Tunnel in 2013. After the successful completion of that project, CDOT began the widening of the West Bound Tunnel in 2014. Both projects had a limited schedule for tunnel construction of just nine months. The innovative blasting and demolition of the existing tunnel lining was a crucial component to the success of both projects. During the construction of the West Bound project in 2014 a large amount of surface bench blasting using conventional methods ran concurrently to the West Bound tunnel excavation to allow for enough room for the new tunnel portals."

Jan 1, 2016

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Thomas J. Crocker, Galen G. Waddell, Eugene H. Skinner

This paper describes a method of measuring initial and long-term deformations which occur in the medium surrounding mine accessways, and discusses the importance of this type of measurement in assessing support-problem areas. Delineated are (1) description of the rock-deformation monitoring equipment, (2) results of two field tests which monitored rock deformation around 4-foot-diameter raise bores, and (3) a numerical-analysis (finite-element) technique to correlate theoretical with experimental results. Instrumentation developed provided the sensitivity and resolution needed to measure rock deformation around a full-scale raise bore during excavation. Results of the tests conducted at the Lucky Friday mine, Mullan, Idaho, show the relationships between (a) de- formation vs. time, and (b) deformation vs. bit progress. Based on theoretical evaluation of the initial deformation, the medium appeared to behave elastically. Using an estimated field stress of 5,500 psi and Poisson's ratio of 0.20, the gross modulus of elasticity of the rock was calculated to range from 3.15 to 6.0 x 106 psi (with one outlier which was determined to be >12 x l06 psi).

Jan 1, 1971

By Herbert E. Lindberg

Laboratory-scale intact and jointed rock masses were tested in field and laboratory experiments to investigate tunnel response in high stress environments. In most of the experiments the tunnels were modeled by a rigid-plastic foam polyurethane with a crush strength of 3.4 MPa (500 psi) and emphasis was placed on jointed rock parameters: joint sets (single set of parallel plane joints versus a double set of orthogonal parallel plane joints), joint plane angle with respect to the direct loading direction, and joint spacing. Other parameters were loading stress, loading direction, and tunnel reinforcement strength. Results show quantitatively the increase in tunnel deformation in jointed compared with intact rocks, double versus single joint sets, and large versus small angle between the joint plane normal and the loading direction. A surprising result was the decreases in tunnel deformation with increases in the number of joints across a tunnel diameter. The efficacy of scale modeling with laboratory-constructed rock was tested by modeling complex reinforced concrete and steel tunnel reinforcements in jointed rock masses and comparing the results with large scale tunnels previously fielded in highly jointed granite. Tunnel response was reproduced in surprising detail, including concrete fracture, steel liner bending and fracture, and critical load to produce these responses. The scale models also allowed sectioning of the jointed rock masses to observe gross sliding along the joints that accompanied tunnel failure.

Jan 1, 1982

By Gary English

"Tunnel safety is evolving as science, engineering and technology make advances. Applicable safety codes and standards simply do not cover all the potentials of design, construction and operation. This paper reviews a series of tunnel projects code gaps in Seattle USA that were uncovered during the design and construction of a new highway tunnel, conversion of bus tunnels to combined road and rail tunnels, new rail tunnels using TBM and NATM, conversion of a road tunnel to light rail, and retrofit of an existing road tunnel to add lanes and improve safety systems. The perspectives of the ‘fire code official’ (Authority Having Jurisdiction) on methods to identify and resolve gaps in safety code and standard regulations, while garnering the consensus of the owner, designer, and contractors are presented. Additionally, the emergency responder command perspective on safe tunnel design, tunnel rescue during construction and operational safety is explained TUNNEL SAFETY EVOLUTION The underground has become nearly the only option to provide essential transportation corridors to continue our economic growth in key global areas. Tunnels are not built on a whim. Often significant portion of a regions wealth are invested to meet current, and hopefully future transportation demands. There are more transportation tunnels being built now than at any time in the planets history. The location of these tunnels is often selected for us based upon regional demand. Most commonly under densely populated urban centers and between populations’ centers to bypass geologic conditions like mountains and water bodies. Tunnels are being built in unforgiving soils, between tectonic plates, in extremes environmental conditions and often, under the very heart of the highest density population centers on the planet. All of these locations can bring with it conditions that challenge our common assumptions about safety. These extraordinary locations and soils create risks for both those constructing the tunnel, and in design engineering to meet the ‘minimum’ requirements at the lowest costs. There is lengthy history of above ground safety. Most countries and major local jurisdictions have adopted, or created safety requirements for the construction of above ground buildings. Through decades of use, these safety requirements have evolved, changed and been expanded to cover a wide gamut of actual and potential safety risks. However, the use of the underground for tunnel transportation corridors has grown exponentially with limited attention to safety requirements."

Jan 1, 2016

By William I. Gardner

Optimum design of a structure obviously requires a thorough knowledge of the materials to be utilized in its construction. When the structure is a tunnel, a most important element in its design and construction is the geology. As a tunnel may be many miles in length and at depths of hundreds or thousands of feet, we face a real problem to meet the needs of the designer and builder. How can we determine the properties of our construction materials in this situation? Engineering geology has had a formidable challenge to meet the requirements of conventional excavation methods; the advent of machine methods for rapid excavation compounds the requirements for more detailed and more precise geological knowledge of the tunnel site. This chapter will discuss the means now at our disposal to meet the challenge to produce the required data on the tunnel site in the preconstruction stage. Our considerations will be directed towards construction of a free-flow tunnel, primarily in fractured rock formations, without any requirements for the rock mechanics type of in-situ tests that might be made for a pressure tunnel or for a large opening for an underground power plant. In essence the investigation must determine: (1) The geologic conditions affecting the type of construction equipment and excavation method of the rock to be broken and removed. (2) The quantities of water and gas to be encountered. (3) The strength and stability of the material surrounding the bore and its need for support and lining. GEOLOGICAL FACTORS AFFECTING TUNNEL DESIGN AND CONSTRUCTION The engineer or contractor may classify the rock as either competent or incompetent or more pointedly as "good" or "bad" ground. The geologist may bestow a precise petrographic name upon the rock, such as granodiorite or indurated tuff breccia or name the formation, as Mancos shale, for

Jan 1, 1970

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By A. A. Mathews

During the past year (1967-68), there have been many instances of either partial or complete failure of a tunnel-support system. It looks like the art is in a pretty sad state, but as long as we permit the field of tunnel design to remain basically an art, that's about what we can expect. The application of scientific principles to tunnel design involves much more than assigning values to a series of factors in an equation. I am reminded of the case where the engineer calculated that steel ribs with struts were required to support a horseshoe-shaped tunnel in firm ground. The contractor had driven several hundred feet without installing the struts when the engineer visited the job. When he was informed that the struts had been left out, he fled the tunnel in alarm. As one authority has so aptly put it, "There is far too much calculating and too little observing." Initially, one might think of a tunnel support as a structural member, such as a strut or arch which is installed in order to support some definite load. Similarly, a tunnel lining might be considered as a treatment of the interior surface of the tunnel in order to produce desired aesthetic, hydraulic, or architectural results, or to serve a protective function. Actually, many linings, such as a concrete lining, serve a dual purpose and support a load as well as satisfy other requirements. Not too many years ago a tunnel, during the driving or excavating stage, was considered to be either supported or unsupported. In recent years, however, several techniques have been developed, which by helping the tunnel to support itself, permit the elimination of separate structural support. Since these techniques in many cases actually become a substitute for the conventional types of supports and linings, a state-of-the-art review would hardly be complete without including them for consideration. Thus, for the purpose of this discussion, we shall define tunnel supports as any system or technique which effectively maintains the integrity of the tunnel opening. In their chapters, both Jacobs (No. 6) and Lippold (No. 7) pointed out how support systems have advanced from timber supports to steel supports

Jan 1, 1970

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By Brian Gettinger, Jared Barber, Richard Weatherly, Shannon Dunne, Jeff Masek, Chuck Wolf, Fazle Rabbi, Jack Canfield

During Hurricane Harvey over 60% of the 39 WWTPs, including the low-lying 25 MGD Sims North WWTP, and one third of the 382 lift stations owned and operated by the City of Houston were flooded resulting in extensive facility damage, loss of service and uncontrolled release of untreated wastewater into bayous and creeks. In response, the City has embarked on an effort to improve system resiliency by consolidating at-risk facilities with a network of deep sewer tunnels. These tunnels will provide secondary benefits to the collection system of augmenting the capacity of the existing 6,000 miles of sewer mains and lowering the collection system profile in poor performing areas. Investigations on the cost to mitigate the flood damages by raising the liquid stream processes at the Sims North WWTP is estimated at nearly $450 million. Instead of spending $450 million to raise the plant, the funds will be directed to providing a more robust and resilient wastewater system for the Sims basin area of Houston. The backbone of this new system is a 4.5-mile-long, 110 inch diameter deep gravity sewer tunnel that will convert a system heavily reliant on distributed lift stations to a majority gravity system with a deep consolidated lift station at the Sims South WWTP. This will also allow the City to address the flood prone infrastructure at Sims North and consolidate its operations into a single permitted outfall for this collection system. This approach is the outcome of a team effort focused on maximizing system resiliency and sustainability for the next 100 years. By thinking outside the box, the City of Houston will not only mitigate the flooding risk at Sims North WWTP, but also solve regulatory and operational challenges throughout the sewershed and deliver a winwin on multiple levels.

Jun 13, 2021

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By Edward S. Plotkin

The tunneling construction industry faces a new challenge in endeavoring to comply with the multitude of regulations and standards of the Occupational Safety and Health Administration and to work following accepted and experienced tunneling practices. Tunnel inspections appear to be gaining in priority. The national OSHA inspection activities reported for the year 1976 in the construction industry are as follows: 989 Inspections 45 As result of Accidents 186 As result of Complaints 605 General 153 Follow Up 34% Were found to be in compliance 714 Citations were Issued 1,825 Violations were found (201 of which were serious; 1573 were non-serious; 51 were imminent danger. There were no recorded failures to abate a violation in our industry.) The five general priorities by which a company would be scheduled for an inspection in descending order are: imminent danger situations, reports of fatal accidents or catastrophies, inspections in response to valid employee C( taints, inspections of work places covered by National Emphasis Program NEP, (OSHA's NEP has been designed to impact on any industry having a very high injury or illness rate) and finally random inspections of work places covered by OSHA. The following criteria in selecting companies for random inspections is used by OSHA.

Jan 1, 1979