Search Documents

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By James E. Friant

The technology applied to shaft sinking has lagged far behind other construction activities. While surface oriented construction and mining have made great strides with new processes and equipment, the majority of shafts sunk currently still follow a drill, blast and muck-out cycle developed in the 16th century. Today, in 1979, the shaft sinking industry is in the midst of its own private industrial revolution. Millions of dollars are being spent annually by industry and government alike to spring the art of shaft sinking into the 20th century. The objective of this paper is to review a few of the newest mechanized schemes for shaft sinking. This is not a theoretical review, however, but a practical one, and deals only with hardware and projects which are currently on jobsites. Figure 1 shows the equipment. On the left is the 241SB 184, a 24 foot diameter blind shaft borer. This machine is currently at about 200 feet, constructing a coal mine shaft in Alabama. It is built and utilized in a manner similar to a tunnel borer. In the upper center is the 1211SR, a 12 foot diameter blind shaft reamer. This machine follows a 6 foot pre-drilled blind pilot hole, and is at work in Chicago. On the upper right is the 121BR, a powerful new blind drill. Just below it is the conical drill head for the 121BR which can utilize either carbide or standard disc cutters. At the center bottom is an expandable back reaming head which can be used to enlarge a drilled shaft up to a maximum of 16 feet diameter, or can be used to produce a shaft having several diameter changes. This equipment is also in use in Chicago.

Jan 1, 1979

By Don Runge, John T. Zeni

Cuprex Limited is currently developing a small gold mining operation in Central Australia in the Tennant Creek field. In February 1984, the company undertook a feasibility study on the project and operations commenced in August 1984. Ore reserves are located between 230 and 280 metres (755 ft and 919 ft) below surface and ore extraction required the establishment of a shaft network for access, ore hoisting and ventilation. Zeni Drilling Company from West Virginia, U.S.A. was contracted to blind drill two shafts for the project. Blind drilling was selected for various reasons, including timing which related to cost efficiency. The blind drill shaft technique has proved successful in this application and with enthusiastic and innovative support from the mining industry, will prove an efficient and cost effective means of accessing and operating underground mining projects of all sizes in the future.

Jan 1, 1987

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

Many block caving operations experience difficulties during undercutting, resulting in draw horizon damage, production loss and extensive drift repairs for the life of the block cave. This paper deals specifically with block cave undercut aims strategies, methodologies and management to avoid the problems indicated above.

Jan 1, 2000

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

By Debbie Nakamura, Daniel Tempelis, John E. Shamma

The Metropolitan Water District of Southern California established a Board of Consultants to assist them in administering the design and construction of the Inland Feeder Program tunnels. The Board acts as an expert review body for the owner, looking at key issues that can potentially impact the success of the program. The use of the Board evolved over the life of the project, and its composition was modified to better address the needs of the owner, and the Program requirements. The experience, function, and value of such a board is analyzed and discussed in this paper.

Jan 1, 2003

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By Ted Nye

This paper describes a number of aspects of the design and construction of a driven tunnel which forms part of the Boggo Road Busway project. The driven tunnel is 430m long with an excavated width of 15m and a full tunnel excavation height of 8m. The first section of driven tunnel was excavated under the heritage listed Boggo Road Jail for a length of 120m. The main jail buildings and perimeter walls were built in 1908 and are of brick construction. Ground cover over the tunnel beneath the jail site varied from 5.5m to 8m and as a consequence the predicted settlement values and their potential to cause damage to the buildings were critical to determining and obtaining approval for the selected tunnel alignment. The geology along the driven tunnel alignment was very variable, providing mixed face tunneling conditions and ranging from surface residual soils to high strength rock at depth. The maximum ground cover above the driven tunnel is 20m.

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By Johnston, T. L.

BISMUTH is found as native metal associated with tin, copper, cobalt, silver, gold, or other metals and in a variety of ores. The more important ones are: bismuthinite (bismuth glance), Bi2S3; bismite (bismuth ochre), Bi2O3.3H2O; and bismutite (bismuth carbonate), Bi2O3CO3?H2O. Of lesser importance are the arsenate, telluride, and vanadate. The sulfide is the most common; the others are often oxidation products from this mineral. Bismuth minerals have been found in various places in the United States, principally in Colorado and Utah, but no ores are mined solely for bismuth. In the Granite mining district of Beaver County, Utah, a stratum of limestone about 6 ft. thick has been almost completely replaced by contact minerals in which bismuthinite associated with pyrite and molybdenite was found intergrown with silicate minerals. In the early days a few small lots of ore assaying 7 to 10 per cent bismuth were shipped from this district. Native bismuth has been found in the Clifton and Tintic districts of Utah. Bismuth is produced as a byproduct in the refining of lead, copper, gold and silver ores, it being recovered from the anode mud from the Betts process. Deposits of bismuth minerals exist in Argentina, Aus¬tralia, China, Japan, Germany, Spain, Peru, Bolivia, and Canada, but Bolivia is the principal, producer and could easily supply all of the present world's demand.

Jan 1, 1933

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Compiled by Staff

"INTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that: appear in scientific, technical, and trade journals; in "" proceedings of conventions and seminars; in' reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable.This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 196O 2; and these 5- year lists of publications and articles: from January 1, 1965, to December 31, 1969 4, from January 1, 1970,to December 31, 19745 , from January 1, 1975, to December 31, 1979 6 , from January 1, 1980, to December 31, 1984 7 , and from January 1, 1985, to December 31, 1989 8."

Jan 1, 1994

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964