Search Documents

By Jan M. Andersson

This paper will discuss the background information about rock cutting tools used for soft ground excavation, their history and evolution. A brief review of the current state of the art manufacturing technology will be presented and some parameters related to the material used in the drag and conical type pick cutters and their impact on their life and performance will be explained In addition, the selection procedures for choosing the right bit for excavation of a particular geological formation will be reviewed A set of guidelines will be provided for initial selection of the tools for various machines and rock formations. The methods for estimation of the tool life in various materials and the influencing parameters along with limitations of the rock cutting tools will be discussed as well.

Jan 1, 1998

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

By Eric Reale

The New York City Department of Environmental Protection (DEP) is currently building City Water Tunnel #3 beneath the city. The purpose of this tunnel is to improve water distribution to the city and to allow the DEP to inspect the older tunnels and make the necessary repairs. These older tunnels have been in continuous operation since the early 1900's. Construction on the Third Tunnel is planned in four stages. The Nelson Street Shaft, which is the focus of this paper, is part of the second stage.

Jan 1, 1989

By Robert W. Gordon

The art of excavating tunnels with continuous, full-face boring machines began almost 90 years ago, in the early 1880's. At this time, Colonel Beaumont designed and manufactured a seven-foot diameter tunneler for boring under the English Channel, Despite the absence of modern materials and manufacturing techniques, Beaumont's tunneler, powered by compressed air piped in from the surface, was quite successful. During its short, but impressive existence, this machine set a record of advancing in chalk 50 feet per day for 53 days - which is impressive even by today's standards. Despite the apparent success of this early tunneler, almost 80 years passed before any further significant development was accomplished in this field. Demands from the construction and mining industry and society itself have motivated the development of the modern tunneling machine. Our rapidly growing civilization needs faster, less expensive and safer means of excavating tunnels. Space age technology and materials have played a major role in making hardrock tunneling machines possible.

Jan 1, 1970

By M. Abouhamad

According to the Canadian Urban Transit Association (CUTA), 140 Billion CAD is required to maintain, rehabilitate, and replace subway infrastructure between 2010 and 2014. The current practice adopted by transit authorities for prioritizing subway stations for rehabilitation is based on the station structural needs. While this classification is reflective of station condition, other factors, such as station size, location and passenger capacity, play an important role. The criticality of a station is an index that represents the functional importance of a station depending upon a set of identified factors. The system criticality is based on several attributes, such as station location, size, and nature of use. This paper presents a novel method of clustering subway stations for rehabilitation priority based on their criticality level. The different stations in a subway network are rated according to their relative importance against predefined attributes. The weights and scores of the attributes are computed with the help of experts and current subway network data. The analysis is done using the Fuzzy Analytic Network Process (FANP) to accommodate the subjectivity of human judgment as being expressed in natural language which entails ?fuzziness? in real-life problems and account for the interdependency between the selected attributes. The output of the model is a criticality based clustering of subway stations. The proposed framework helps authorities prioritize stations for rehabilitation and highlight stations with more criticality for a more robust asset analysis.

Aug 1, 2013

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By Ethan Steward, Robert Eades, Kyle Perry

Shock tubes, either gas or explosively driven, are often used for physical modeling of free field explosions or arena testing. The use of shock tubes often requires less setup time of subjects and smaller driving forces to create pressure versus time waveforms similar to that of arena testing. However, the effects of the shock tube cross sectional geometry on waveform properties is uncertain while free field explosion wave propagation and estimation is well studied.

Jan 1, 2018

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By Jess H. Albino, Girish Roy, James M. Monsees

Construction of the North Hollywood line of the Los Angeles Metro System required crossing the Hollywood Fault as the twin transit tunnels extend into the San Fernando Valley. The Hollywood Fault is considered active and represents the largest active fault that the North Hollywood Redline extension will cross. The feature is a thrust fault with the north plate overriding the southern plate and creating the Santa Monica Mountains in the process. South of the fault lies the alluvial valley and Hollywood. North of the fault are the Santa Monica Mountains which rise locally to more than 1200 feet. The average overburden at the seismic section is about 300feet and is overlain by Runyon Canyon Park, a municipal park with environmentally sensitive areas. The actual fault plane was anticipated to lie within the southernmost120 feet of the 600 to 700-foot-wide fault zone. The special seismic section constructed for the tunnels consisted of an enlarged cross-section with special lining, drainage and finish features that will facilitate the restoration of metro service in case of a major event occurring on the Hollywood Fault. The discussion will address the geology, the procedure used to define the design event and predicted displacements, the unique design features as well as the construction methods used and the instrumentation and the results obtained.

Jan 1, 1999

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By Patrick J. Doig

The Crosstown 7 Collector System, Contract C28G11, is part of the Milwaukee Metropolitan Sewerage District's Waste Pollution Abatement Program. The contract involves the construction of 1.6 km (1 mile) of 3 m (10 ft.) diameter tunnel in soft ground. The tunnel is 10 m (35 Ft.) below surface and passes through a variety of soils. The eastern leg of the tunnel along Bruce Street is mainly in till material, a stiff, relatively dry clay. The northern leg along 16th Street starts in till, and continues in estuarine deposits - moist sticky clay, with intrusions of alluvial sand and gravel. The contract specifications required that the tunnel be constructed either under compressed air or with an earth pressure balance tunnel boring machine. The S. A. Healy Co., the general contractor, chose the latter option. Additionally, a single pass, pre-cast concrete segmental liner was selected as the lining system. The mining machine was manufactured by Lovat Tunnel of Canada and the segments were made by the Sehulster Company of Milwaukee. The use of this combination of machine and lining is relatively new to the United States and this tunnel is the most extensive built to date with a gasketed, segmental single pass lining for transportation of fluids. This paper details the various aspects of the construction of the tunnel and associated shafts.

Jan 1, 1989

By Roger J. Goodman, Don Riva

"IntroductionCrows Nest Resources Limited (CNRL), a wholly-owned subsidiary of Shell Canada Resources Limited, is nearing completion of its first coal project, located in southeastern British Columbia. CNRL shipped over 700,000 tonnes of thermal coal to foreign markets in 1982. With the completion of the metallurgical coal plant in December, 1982, shipments of both thermal and metallurgical coal will increase substantially in 1983 and will approach the anticipated operating capacity of 3.0 million tonnes in 1985. The Line Creek Mine lies some 25 kilometres north of Sparwood in southeast British Columbia (Fig. 1). The open-pit mine is located on top of Line Creek Ridge, with coal being hauled 16 km to the thermal and metallurgical coal preparation plants, situated adjacent to the already existing Canadian Pacific Railway. Most of the coal is moved by 108 car unit trains by CP Rail to coal ports in Vancouver, where it is loaded onto vessels destined for overseas markets. Some smaller scale car load shipments are moved by rail to contiguous markets in the Pacific Northwest. History The southeastern British Columbia area, known as the East Kootenays, is steeped in a rich coal mining heritage, dating back to the latter part of the nineteenth century. Predecessors of Crows Nest Resources Limited were instrumental in developing the rich coal reserves in the area. In 1887, William Fernie, a pioneer-cum-prospector recognized the potential of coal deposits in the East Kootenays. Spurred by the relentless push west of the Canadian Pacific Railway through the Crows Nest Pass area, Fernie recognized that it was just a matter of time before the steam locomotives provided him with his required market. That time arrived in 1897 when Fernie helped to form the Crows Nest Pass Coal Company and coal mining commenced at Coal Creek, near his namesake town of Fernie. During its almost 70-year history, this company produced over 48 million tonnes of steam coal and 8 million tonnes of coking coal. In 1965, the Crows Nest Pass Coal Company was re-named Crows Nest Industries, to better reflect its expanded interests into forest products, and it is the latter company which Shell Canada Resources Limited acquired in 1978. The extensive coal resources of Shell, in both Alberta and British Columbia, were rationalized into one group with the birth of Crows Nest Resources Limited to manage and develop the coal holdings."

Jan 1, 1985

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By David Runnels

In September 1970, the Quebec Cartier Mining Company, started development of the Mount; Fright iron ore mine. The estimated ore reserve is in excess of 1,000,000,000 long tons with an average grade of 31.5% Fe. The run of mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production rate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material of which 50% is waste. The mine is located in the Province of Quebec, close to the Labrador border approximately 600 miles north-east of Montreal. The development of the mine necessitated the construction of an all electric one thousand housing unit townsite along with associated services such as a shopping center, swimming pool, arena, school, etc... A one-hundred mile long, 315 K.V. Dower line was built between the mine site and the Hydro-Quebec 735 K.V. existing power line between Churchill Falls and the Montreal area. The construction near the mine of a beneficiation plant was necessary to upgrade the 31.5% iron ore to a marketable product of 66% iron.

Jan 1, 1977

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By David Cole

THE New Cornelia Copper Co. is mining and treating a 'monzonite " porphyry" copper deposit that is all hard rock. The oxidized surface shell, which constitutes the leachable part of the orebody, is measurably more resistent to crushing and comminution processes than is the underlying sulfide portion. The siliceous ribs running through the whole orebody are harder to crush than the main mass and there is no soft crumbly material to furnish the large volume of primary fines that features the crusher feeds of most other porphyry properties. New Cornelia ore reaches the primary crushers with a greater. proportion of large 'pieces. When the New Cornelia company first equipped its 'property, it used the following machines and flow , scheme to reduce the ore to leaching size:

Jan 1, 1925

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947