Search Documents

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022

By David Mast, Irwan Halim, Seung Han Kim

Nowadays more infrastructure tunnel projects are procured using design-build method. In this environment, the Owner’s engineer would typically provide performance requirements for the design-builder, and the Contractor’s designer would work with the contractor to design the tunnel lining based on the Contractor’s means and methods and manufacturing process. This paper will describe the typical requirements provided by the Owner based on its design objectives, and the means and methods by the Contractor that would significantly impact the design. Project examples and recommendations for Owner’s requirements will be provided that can optimize the design and still achieve the Owner’s performance objectives.

Jun 13, 2021

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By S Pradhan, A Kuras, R Mahajan

This paper describes the design of the precast concrete segmental lining for the 13.1 m internal diameter and 450 mm thick, 2.4 km long mainline tunnels for the Waterview Connection project in Auckland for the New Zealand Transport Agency.The design and detailing of this segmental lining presented some noteworthy challenges, including an alignment that has sections of low cover in soft ground. Key points of interest are that this precast segmental lining is the largest to ever include steel fibres as the primary method of reinforcement and the lining includes cams on circumferential joints to control ring deformation.The paper describes some of the key design decisions that were made in a collaborative manner with the construction team, tunnel boring machine manufacturer, segment manufacturer and the designers.CITATION:Mahajan, R, Kuras, A and Pradhan, S, 2014. Design of segmental lining for Waterview Project, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel project, a U.S. EPA/ DOJ CSO Long Term Control Plan Project. The system will provide at least 10.3 million gallons of storage in a 16.5-foot finished ID and 6,660-foot-long rock tunnel. The system will reduce both overflow volume and number of overflow structures on the Cuyahoga River. The project includes deep drop shafts and more than 3,000 linear feet of 48 to 96-inch I.D. sewers installed by trenchless construction methods. This paper will discuss the project background, ground conditions, and other challenges overcome during the design phases.

Jun 13, 2023

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By S Porter, R Woodall, N Weeks

Nelsen, Porter and Wilson (1996) provided some preliminary concepts for the design of the Melbourne City Link tunnels. At that time, the City Link project was in the early design phase whereas now it is nearing completion. This paper provides details of the actual design adopted for the various sections of the tunnels as well as some commentary on the design process. The tunnels form a critical element of the project and the design of both driven and cut and cover tunnel sections is a significant factor contributing to successful project execution. Geology, hydrogeology, site constraints, traffic management and program were important design inputs. Design for the cut and cover sections in particular varied significantly in response to these differing inputs.

Jan 1, 1999

By J. N. Eskilsson, W. P. Chen, J. L. Kaplin, V. S. Romero

The Massachusetts Water Resources Authority is currently improving its primary water supply system for the Boston Metropolitan area. The improvements planned by the Authority, which provides water for 46 communities and over 2.5 million people in eastern Massachusetts, include the MetroWest Water Supply Tunnel (MWWST) to provide redundancy in the transmission system, a large capacity water treatment plant and extensive covered storage facilities. The 28.3 km (17.6 miles) long, mostly 4.3 m (14 ft.) I.D. MetroWest Water Supply Tunnel will allow repair of the aging Hultman Aqueduct, which for 56 years has served as the transmission main from the water supply reservoirs to Boston. On completion of the tunnel, the old pipeline aqueduct will be repaired and brought back into service as a parallel, redundant transmission main. This paper describes design considerations and the design process for pressure tunnels in general and the MWWST in particular. It provides an overview of how the design of pressure tunnel and shaft components progresses.

Jan 1, 1997

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By Henrie Henson, Dan Burroughs, Shyi-Shyong Jiang

Jan 1, 1993

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By Pedone Ezio Michele, Mohamed Dahir Holad

"The 4c segment is a part of the ""Oman National Railway Project” linking the mining area in the surroundings of Thumrait and the port of Salalah. It is 90 km long and the last 40 km stretch crosses a mountainous area near the city of Salalah. The project includes the excavation of a 33 km double and single bore tunnel and 10 km of safety tunnels. This mountainous area is a holiday destination for Omanis, thanks to its beautiful landscapes, especially in summer time due to the monsoon rains. The tunnelling design had to take into account both these environmental constraints and the limestone rock formations crossed, which are affected by significant karst features. Given the context, the conventional tunnelling method has been preferred. INTRODUCTION The Oman Railway Project (Fig. 1) covers the construction of approximately 2,150 km of railway line for freight and passenger transport which will connect together Oman’s main towns and industrial sites and it will form part of the Arabian Peninsula railway system “GCC Project”. The non-electrified double-track railway line must guarantee a speed of 220 km/h for passenger trains and 120 km/h for freight trains and must guarantee the transit of AAR (Association of American Railroad) H and D plates using clearance envelope according to AREMA (American Railway Engineering and Maintenance-of-Way Association) requirements. The design alignment must have maximum radiuses of curvature of 3,250m and a maximum gradient of 1.0%. The project is divided into 9 constructional and functional segments. •,Segment 4c will be constructed in the southern region of Oman, close to the border with Yemen, to connect the town of Thumrait with the Port of Salalah. •,Segment 4c will run through the Dhofar region and will be mainly used by the freight traffic which currently travels by road."

Jan 1, 2016

By Daniel N. Adams

The University Link project extends Seattle?s light rail from downtown to University of Washington (UW). It includes 5.0 kilometers (3.15 miles) of twin-bored, 6.4 meters (21 feet) excavated diameter tunnels, and two cut-and-cover stations. The Capitol Hill Station (CHS) requires an excavation 170.7 meters (560 feet) long, 22.6 meters (74 feet) wide, and 22.9 meters (75 feet) deep. The University of Washington Station (UWS) requires an excavation of about 238.4 meters (782 feet) long, 21.3 meters (70 feet) wide, and 33.5 meters (110 feet) deep. The project is within the glacially diverse soils of the Puget Sound region, below groundwater. This paper highlights major station and tunnel design elements, including the approach to support of excavation at both station boxes, and the site staging requirements.

Jan 1, 2008