Search Documents

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Pedro Alejandro Samané Tuni

El presente texto describe las soluciones que disponen los geólogos e ingenieros para actuar de forma adecuada en la planificación, diseño y construcción de los proyectos, así como se muestran los errores de concepto que todavía persisten cuando se usan las clasificaciones geomecánicas.

May 1, 2013

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By J. Gentry

Chemical grouting has been successfully used for over forty years to control the movement of groundwater in a wide variety of applications including tunnels, subway systems, sanitary sewers, mines and construction projects. This paper illustrates the versatility of chemical grouts by reviewing three projects where chemical grout was utilized to address some very difficult water control challenges. The featured product is acrylamide which can be used alone or in conjunction with other types of grout such as cementitious products. Acrylamide grout is injected as a two component product that will react and form an impermeable gel when the components combine. There are notable differences between the acrylamide based products and cementitious products. The most notable and significant difference is that acrylamide is a true solution grout that contains no particulates and has a viscosity of 1-2cps. This feature enables the acrylamide grout to penetrate very small geological features that other grouts could not penetrate and to seal small cracks and fissures where groundwater seepage is occurring. The product also has an adjustable gel set time from a few seconds to several hours which enables the operator to determine the product travel before it forms a gel. When properly applied the product has a half-life in the soil of 362 years (per testing by the US Department of Energy).

Feb 27, 2013

Many of the world?s largest existing mines are considering substantial step changes in production volumes, compensating for declining ore grades while trying to address increases in world demand for resources. The natural configuration of coal deposits allows for many mine development openings along the strike to access the ore body and thus increase volume. Similarly, with iron ore the nature of the deposits means that additional capacity can easily be added by opening up new mesas and providing extensions to infrastructure. On the other hand most of the non-ferrous metaliferous deposits form vertically and additional extraction volume comes from increasing depth. Underground mining from the base of the strata allows for large extraction rates, but block or panel caving operations develop at rates dictated by the geophysics of the overlying strata and the need for massive tunnelling developments to establish sufficient extraction points for high volumes. For really big mine production capacity, open cast mining still allows the easiest development of more massive mining techniques. But there remains the question of whether there are limits to how large an open cut mine can become in terms of throughput?

Feb 27, 2013

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By E. Farrokh

Estimation of the cutter life and cost is a part of evaluating performance for a hard rock TBM in any project. Various approaches has been proposed for calculation of disc cutter life in various rock types based on machine specifications and rock strength and abrasivity. Cutter change time is a parameter that is used in some of the estimates and is defined as the average time required for changing a cutter on the cutter head and cutter life is the number of cubic meters of excavated rock per each disc cutter. Analysis of cutter life information of several tunnel projects from around the world has revealed that the published models for estimation of cutter consumption require some revisions to offer a more accurate prediction. The preliminary analysis of data shows that the average cutter change time is approximately 66 minutes for different cutter sizes and there is a minimal difference between corresponding cutter change times of the large (e.g. 19 or 20 in) versus smaller cutters (e.g. 15.5 to 17 in). This paper reviews the available and published cutter life data from various projects. It also introduces new models for estimation of cutter life and cutter change time as part of TBM down time and utilization analysis.

Feb 27, 2013

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By Rohan Stevens, Katsuhiro Kameyama, Osamu Iwata, Jinming Liao

In densely populated cities such as Hong Kong, where unoccupied space is becoming more valuable as the population grows, city planners are more often looking to underground space to meet the increasing need for transportation and services. Given the dense population of people, amenities and high-rise buildings above or near such underground space, it is essential to minimise any disturbance and potential damage during construction. Hence, the excavation of hard rock to develop such underground space can be highly restricted, expensive and time consuming. This is the case for many of the tunnels currently being excavated by drill and blast directly underneath Hong Kong’s busiest business districts and most popular residential areas.

Jan 1, 2013

By D J. McLane, J T. Rathbun, B T. Lusk

The dynamics of explosive detonations are understood, however recreating a real-world, full scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this paper is to better the understanding of how the waveform characteristics resulting from an explosive detonated within a shock-tunnel differ from those in an open-air arena test. The variables of comparison between an open-air arena test and those conducted within a shock tunnel are peak pressure, impulse, shock wave velocity, and cross sectional shape of the shock front. Understanding how these variables differ, tests utilizing a shock tunnel can be conducted with a higher degree of accuracy and repeatability.

Jan 1, 2013

By Joshua Hoffman

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. Student chapters help with this effort but what are they doing and are there things they could learn from each other? This paper discusses the University of Kentucky Student Chapter's efforts to grow membership, retain its recruits, and integrate them into the explosives industry. Several social and professional events during which the students are able to meet and network with members of their future industry are introduced. The special relationship that has been fostered between the University of Kentucky and Missouri University of Science and Technology is discussed. Professional development initiatives which are critical for a student to become vested in the industry are shared in this paper. These opportunities which range from internships to research positions allow a person to get a better understanding of the explosives industry and find the niche that best suits them. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements there is a trend of job placement primarily in the engineering industry. By providing these students with the chance to learn more about the explosives industry and get hands on experience more of these future engineers and professionals can be retained after their graduation.

Jan 1, 2013

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013