Search Documents

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By P. K. Kaiser

A rational approach for the design of fully grouted bolts in underground excavations is presented. An analytical model involving elasto-plastic concepts and the mechanics of bolt/ground interaction was developed and tested by comparison with laboratory tests and field measurements. The theory elucidates the influence of shear stress distribution, bolt pattern and geometry on tunnel convergence. Laboratory simulation has provided convincing evidence to support the theoretical predictions. A dimensionless bolt efficiency parameter is introduced as a design tool that relates the reduction of tunnel convergence to the bolt length and density. Its application in practice is highlighted by the analysis of one case history.

Jan 1, 1987

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987

By Steven R. Wardwell, Gerald G. Stokes

INTRODUCTION A compaction grouting program to control ground loss, and to minimize surface settlement, was developed for the West Tunnel of the Phoenix Storm Drain Tunnels. The West Tunnel was 4,200 m long, 7.56 m in excavated diameter, and was excavated with shallow cover through the central Phoenix business district. The tunnel could not have been successfully excavated without the compaction grouting program. HISTORY After heated political debate over a ten year period, the Arizona Department of Transportation (ADOT) was granted approval to build the Papago Freeway, an extension of Interstate 10, through central Phoenix. To comply with environmental constraints, a portion of the Freeway was depressed, requiring an excavation 10 meters in depth, thus intersecting surface run-off from the northern section of Phoenix. This required that ADOT and Project Design Consultant, Howard, Needles, Tammen & Bergendoff (HNTB) design a drain system to collect run-off and transport it approximately 4 kilometers to the Salt River through the City of Phoenix. Tunnels were chosen for the main discharge conduits because depth and location of the system made cut and cover construction impractical. A contract for construction of the tunnels was awarded to Shank-Artukovich-Ohbayashi (S-A-O) on May 24, 1984.

Jan 1, 1987

By Chris C. Sundberg, Ronald E. Heuer, Stanley L. Paul, Peter M. Douglass

Use of prestressed concrete cylinder pipe (PCCP) for pressure tunnel liners is gaining popularity with contractors, engineers, and owners. This paper presents loading considerations and a beam-spring computer model approach to tunnel liner analysis, together with ultimate strength (US) and service load (SL) procedures for liner design. The US procedure is best suited to check for adequate liner strength under extreme loading conditions. The SL procedure, based on conventional pipeline design practice, is considered more appropriate when addressing crack control and serviceability under normal working load conditions. Other design and construction considerations are discussed and a design example is presented.

Jan 1, 1987

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By Siegmund Babendererde

Introduction Lyon, with 1.1 million inhabitants, is the third largest city in France after Paris and Marseille. It is a lively industrial centre. Lyon lies at the intersection of many transport routes and at the fluence of Rhone and Saone. Like all large cities, Lyon is attempting to alleviate inner city traffic problems by constructing a metro. Metro construction in Lyon began with tunnels built by cut and cover methods along the streets. Deep diaphram walls, which were back anchored and toed into imperveous strata, formed the excavation walls. It is a very economic and simple method. However during the construction period, it has the disavantage of strangling urban life for several years. It is therefore increasingly being replaced by subsurface tunnelling methods. As it was decided to build the metro tunnel between the Guillotiere and St. Jean stations, and thus cross under the Rhone and Saone, the client, Semaly, put the contract out for a competitive tender in which the general parameters were defined. Line, level and construction method were left to the contractor. There was an extensive examination of the tenders, during which reference projects from competitors in Japan were visited, as well as in Germany. Finally the consortium of Dragages, Campenon Bernard, Colas and Hochtief was awarded the contract to drive this tunnel section with an hydro-shield and an extruded steel fibre concrete lining, a Hochtief design.

Jan 1, 1987

By Joan Weinberg

The economy continued to expand during the third quarter, as real GNP rose at a seasonally adjusted annual rate of 3.8%, up from 2.5% in the second quarter (table 1). Continued job gains (see below), higher incomes, and an increase in installment debt, resulted in a nearly 20% increase in consumer spending on durable goods. Consumer expenditure on nondurables fell slightly, while spending on services continued at a moderate pace. Nonresidential fixed investment climbed nearly 24%, as producers purchased more durable equipment. Residential fixed investment was adversely affected by rising interest rates, which slowed new home construction from January to August, 1987 to a rate 11.2% below a comparable period in 1986. Net exports of goods and services deteriorated slightly, after three consecutive quarters of improvement. The volume of net exports has risen 15% for the year, contributing to economic and employment growth, but large price increases on imports have slowed the improvement in the nominal trade balance. Although U.S. goods have declined in price relative to foreign goods because of the devaluation of the dollar, faster growth in exports is hampered by austerity programs in developing countries, and emphasis in Germany and Japan on curtailing inflation and fiscal deficits.

Jan 1, 1987

By Dennis L. Boley, Francesco Gallavresi, Donald A. Bruce

The authors describe novel aspects of ground reinforcement and treatment as related to soft ground excavation for tunnels throughout the world. Insitu reinforcement for cut slopes (soil nailing), as underpinning (reticulated micropiles), and as direct tunnel support (infilaggi) is introduced. Ground treatment focuses on new aspects of permeation grouting (by the tube'a manchette system), and on jet grouting-a very powerful and positive new technique. Recent developments in equipment, materials, methods and instrumentation are reviewed, with special reference to major tunnelling projects in Italy and Singapore.

Jan 1, 1987

Boring of a 7.5Km long tunnel under the city of Stockholm commenced in January, 1987. The 3.5m diameter tunnel will pass under the buildings and as no ground settlement is allowed, the regulation for water leakage into the tunnel is very strict. Probe drilling will be carried out continuously ahead of the boring and when water is encountered the rock has to be grouted before passing with the TBM. The tunnelling system enables probe drilling to be carried out during boring with the TBM. This has earlier been a capacity reducing factor as the whole operation has been stopped during probe drilling. The project is using a new generation TBM especially developed for hard rock formations which require higher thrust per cutter to get a high penetration rate.

Jan 1, 1987

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

By Carl Barchet

INTRODUCTION Located on the Colorado River on the Nevada-Arizona border about 56 km (35 miles) southeast of Las Vegas, Nevada, Hoover Dam is a gravity arch dam 221 m (726') high for electric power generation and water supply. The head waters of the dam form a large reservoir, Lake Mead. The dam is equipped with two emergency spillways, one in the Nevada abutment and one in the Arizona abutment. Both spillways which are concrete lined and 15.25 m (50') in diameter, were intended for use only if Lake Mead is full and incoming flow of the Colorado River exceeds the discharge capacity of the turbines and regular bypass conduits. In the spring of 1984, a combination of rain and unusually rapid snow melt required the opening of the spillways for only the second time in the 50 year history of the dam. As in the previous use in 1942, the massive discharge of water through the tunnels resulted in severe damage to the concrete Linings of both tunnels. This damage is the result of cavitation which occurs as the discharge water flows at very high velocities over minor irregularities in the concrete lining. The U.S. Bureau of Reclamation has long been aware of the cavitation effect which occurs during these high volume discharges and has been studying solutions. One solution to the problem is to induce air bubbles into the flowing water to eliminate the vacuum associated with cavitation. This solution had been implemented at Yellowtail, Flaming Gorge, Blue Mesa, and Glen Canyon dams by constructing an aeration slot in the inclined portion of their spillway tunnels. Since the spillways of Hoover Dam were already in need of repair, the BUREC decided to construct similar facilities in each of the two 15.25 m (50') diameter spillways coincidental with the other repairs required.

Jan 1, 1987

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987