Search Documents

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By G. W. Rhodes, B. P. Cavan, F. K. Mussger

The New Austrian Tunneling Method (NATM) has been successfully applied to two very different tunneling projects in the U.S.. In the case of Pittsburgh's Mt. Lebanon Tunnels, two original design alternatives were prepared. The NATM alternative incorporating a reinforced shotcrete final lining was successfully bid and constructed. At Washington Metro's (WMATA) Section B-10 Glenmont Route, Wheaton Station and tunnels, a NATM value engineering redesign was prepared for the low bidder. The design incorporating a waterproofing system based on a PVC membrane between the initial and final linings was accepted by WMATA. In both cases, European experience and standards were meshed with U.S. standard practice. Examples of NATM flexibility as an original design and as a value engineering proposal are presented.

Jan 1, 1985

By D. Lee Petersen, Charles R. Nelson, Marvin Marshak

INTRODUCTION Construction is underway on a laboratory cavern 713 m below surface at the Soudan Mine, Tower-Soudan State Park, in northeastern Minnesota. The 13.9 in wide by 11.6 m high by 71.8 in long cavern will provide a laboratory space for basic research in physics, in which experiments can be conducted with greatly reduced interference from cosmic radiation. A first generation experiment, called the Soudan 1 detector, is currently operating in a converted drift 591 in below surface at the mine. The initial phase of the Soudan 2 detector will be an 1100-metric ton unit, which will occupy approximately a 19 m length of the cavern. Control and monitoring equipment will be in a prefabricated shop office enclosure erected in the cavern. The location and planned usage for the laboratory cavern present special excavation, lining, and outfitting requirements. Temperature and humidity control, a relatively clean dust-free environment, and a long service life are required. Low cost and risk to the owner were basic requirements due to the nature of the funding. The most common type of site selected to meet these two constraints is either an operational mine or a civil works facility such as a road tunnel. There are often serious problems for such laboratories because of ongoing operations such as blasting, hauling, etc. Most of these problems do not exist for the Soudan 2 laboratory because the mine is used as a historical site with regular tours only in the summer season. The laboratory owner, the University of Minnesota, and the park owner, Minnesota Department of Natural Resources, are both public agencies of the

Jan 1, 1985

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

Exceptionally weak ground, usually associated with faulting, unanticipated groundwater pressures or flows and exceptionally high stress concentrations are some of the hazards which confront the underground excavation engineer. One or more of these hazards can seriously delay or even halt a tunnel or mining project, and methods for predicting these hazards are urgently required, particularly for projects involving high speed drill and blast or tunnelling machine excavations.This paper explores the current availability and the potential for the development of tools and techniques for the prediction of these hazards. It is concluded that systematic and automated geological data collection and interpretation represent the most promising avenue for development. It is suggested that there is room for the use of expert systems in which the computer is used to assemble and organize practical underground excavation experience into an interactive decision making system.

Jan 1, 1985

By Odd E. Hanssen

In April 1982, the contracting Companies, ABV of Sweden and Hoyer-Ellefsen of Norway forming the Consorcio Escandinavo Agoyan, signed the contract for the construction of the civil works of the Agoyan Hydroelectric Project, located in Ecuador, South America. The project is located in the Andes mountain region of Ecuador - one of the smaller countries in this part of the world, located on the Pacific Coast. The contract was signed with the Instituto Ecuatoriano de Electrificación (INECEL), a public institution in charge of the development of all major energy producing projects in Ecuador, for a value of approximately US$ 120,000,000. The contract's main elements are - Concrete gravity dam with a total volume of approximately 210,000 cu m. (60 m wide x 45 m maximum height, 320 m crest). - 2,400 m of headrace tunnel, interior diameter of finished lining 6 m of which 450 m is in-situ tunnel formed in a trench. - Pressure shafts, 132 m long, the lowest meters with sheet lining, the rest with concrete lining. - Powerhouse cavern with an excavated volume of approximately 25,000 c m in which two turbines of 78 MW each will be installed. - Two 140 m tailrace tunnels with a finished diameter (concrete

Jan 1, 1985

In 1972, with the West Lyell Open Pit winding down, mining operations transferred underground. All development tunnelling until the end of the decade was carried out by a fleet of ten pneumatic Jumbos.A decision was made in 1980 to purchase an electric-hydraulic Jumbo and a second was purchased in 1982. Their introduction changed the face of development at Mount Lyell. Significant new demands were placed on main-tenance sections, particularly on electrical reticulation.Subsequently, two further electric-hydraulic Jumbos were purchased from Agnew Mining in 1984, and successfully overhauled and commissioned. As well, two electric-nydraulic production drilling rigs have been purchased. Only one of the original pneumatic Jumbos remains in service.

Jan 1, 1985

The concentrated efforts now being directed towards the development and application of monitoring and control techniques have now resulted in their widespread use in UK mines together with evidence of benefits resulting from their application. There is little doubt that the longwall method of producing deep mined coal will continue but will be made more reliable and efficient with the aid of control technology. The major fields of research and development work are concerned with planning and design of mines and mining equipment; management and engineering information; and automation of coalface, tunnelling and transport systems. The principal achievements now in widespread use are: the standard computer system MINOS, widely applied to mine transport, coalfaces and mine environment; extensive use of machine condition monitoring leading to condition-based maintenance; underground automation of conveyor systems and guidance systems for ranging drum shearers and boom-type roadheaders are being widely introduced.

Jan 1, 1985

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By W. D. Presley, T. R. Harrell

This paper will be a case history of the shaft and tunnel concrete lining techniques used at the Rocky Mountain Pumped Storage Project located in northwest Georgia. Emphasis will be placed on the shaft lining techniques with only a brief description of the tunnel concrete lining techniques. The 10.67 meter (35 foot) diameter shaft and tunnel concrete linings are 0.61 meter (2 foot) nominal thickness with a single row of reinforcing bars. The tunnel was placed in 18.29 meter (60 foot) lengths with bulkheaded end sections. The 172.72 meter (566.68 foot) vertical shaft was placed in 3.05 meter (10 foot) high sections using jump forming techniques.

Jan 1, 1985

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By Madan M. Singh

Increasingly, geotechnical data are being collected for various types of coal development projects. In many cases, a specific design concern is addressed. However, many data collection programs are not intended to immediately support mine design activities or to resolve a specific concern. The following discussion describes some current geotechnical approaches in mine planning, development of reserves, and peripheral activities. Types of Data Collection Programs Geotechnical data collection is increasingly becoming a part of standard coal exploration programs, performed along with stratigraphic evaluations and coal quality tests. The aims of such programs vary. The purpose of the exploration may be to fill out the portfolio on a block of reserves that is to be sold, leased, or held for potential future development. In such a case, a generic suite of geotechnical data are collected. The resulting engineering reports may touch on the more well known mining problems of the area, but detail may be lacking. The geotechnical data are mostly intended to enhance the saleability of the package. Mine design alternatives are generally not addressed.

Jan 1, 1985

By John R. Bartels

In laboratory testing, the Bureau of Mines established criteria by which common resin-grouted roof bolting systems can be evaluated and compared. Ultimate strength and stiffness were determined for nonten-sioned full-column, point-anchor, tensioned full-column, and debondable resin-grouted bolts, and for variations on full-column boltsn Bolt per-formances were compared using the performance of the 3/4-in full-column resin-grouted bolt as the standard. New and innovative systems can also be qualitatively compared against this standard. Since the medium into which a resin-grouted bolt is installed is one of the most important parameters affecting bolt performance, various host mediums were used in the testing: sandstone, concrete, simulated coal, simulated shale, and plaster. Bolt performances expected in other mediums can be inferred from the response patterns obtained in these mediums. Results indicate several functional differences among bolt types. Where resistance to shear is important, point-anchor bolts may outperform nontensioned full-column bolts at a lower cost. In medium-to soft-strength rock, tensioned full-column bolts perform best. Also, varying the resin-steel ratio seems to have little effect on the properties of a full-column bolt, when proper resin mixing is ensured.

Jan 1, 1985

By Al Sylvester

The drill-and-shoot excavation of the two underground Pumphouses for the Metropolitan Sanitary District of Greater Chicago's Mainstream Pumping Station is described. The construction sequence involved the concurrent excavation and support of the two 19.2 m (63 feet) wide by 83.6 m (274 feet) long by 29.3 m (96 feet) high caverns. Excavation was interrupted after taking the 6.1 m (20 feet) high top heading in order to cast-in-place a 0.2 m (8 inch) thick by 19.2 m (63 feet) wide concrete arch. The remaining 23.3 m (76 feet) of rock was then excavated in benches below the concrete arch. PROJECT DESCRIPTION Twenty-four kilometers (15 miles) southwest of the city of Chicago, Peter Kiewit Sons' Co., in a joint venture with John F. Shea Co., and Kenny Construction Co., has successfully completed the construction of the Mainstream Pumping Station for the Metropolitan Sanitary District of Greater Chicago. The five year, 169 millon dollar project is a vital component in Chicago's Deep Tunnel and Reservoir Plan in that its function is to lift the sanitary/ storm sewage back up to grade from 107 m (350 feet) below ground, and pump it to the treatment facilities 8 km (5 miles) away.

Jan 1, 1985

By N. Melnyk

"FOREWORDThis paper provides a unique description of a method devised for mining a very thick steeply dipping seam of soft gassy coal which was prone to spontaneous combustion. The editors con¬sider that the information in this paper should be important to those who may have to consider mining such seams again at some time in the future and therefore believe that the paper warrants reprinting in the present volume. The author was ask¬ed to review the paper and to add any additional relevant in¬formation. He provided the accompanying footnote, only a month before his death on April 22, 1982.IntroductionIn the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels. and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated.The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not lend themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition the present operations in this particular' seam are being carried on at a level below the former workings, introducing new problems, not encountered on the upper level.Coal will, without question, long continue to be an impor¬tant factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion."

Jan 1, 1985

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By Peter White

The Hemlo Gold District, located on the north shore of Lake Superior, was discovered in 1981 and will become one of the largest gold mining camps in Canada. Three major Canadian mining companies are presently developing large orebodies and are scheduled to commence production at various times through 1985 and 1986. This paper describes the types of shaft sinking equipment and technology being used by contractors in constructing the required shafts to depths below 1000 metres. The principal shaft design criteria, types of shaft sinking machinery and relevant manpower allocations are discussed.

Jan 1, 1985

By F. D. Ball, D. E. Gemmell

"Coal mining in New Brunswick dates from the year 1639, when, as today, coal was produced from the area surrounding Grand Lake near the geographic centre of the province. Current production by N.B. Coal Ltd. is approximately 453,000 tonnes per year and comes from a single, thin Pennsylvanian age seam. The history of development and understanding of the geological setting of New Brunswick coals is discussed, beginning with the work of A. Gesner in 1839. The lithostratigraphic sub-divisions of the Pennsylvanian strata proposed by various workers are summarized and the present hypothesis that only biostratigraphic subdivision is possible is detailed. The Pictou Group, which includes the New Brunswick coals, consists of repetitive sequences of sediments consistent with flu vial and upper delta plain sedimentation. The development of coal mining in the province has progressed from horse-powered stream-bank stripping operations prior to the late 1800s through to the present use of open stripmining techniques utilizing eight walking draglines of various sizes. During the intervening years the introduction and eventual phasing out of underground mining occurred with the near termination of the coal mining industry in the province prior to 1973. The coal seam worked by N.B. Coal Ltd. averages 46 cm in thickness, has never been found to be more than 76 cm thick and has both high ash (12.4 -31.1%) and sulphur (4.9-7.8%) content. The wide variety of coal beneficiation studies and tests completed on New Brunswick coals have lead to the conclusion that a washed New Brunswick coal product could be expected with 10 to 12% ash, 5 to 6% sulphur, and 30,225 to 31,388 1/gm. Recoverable coal reserves, including those in the area licenced to N.B. Coal Ltd. and those licenced, although not yet in production, to both the St. Lawrence Cement Co. Ltd. and Provincial Holdings Ltd. at Lake Stream and Beersvil/e, total 60 million tonnes. At present, coal in New Brunswick is removed from prospecting and staking and all existing and future coal exploration and development will be administered by agreement under the Mining Act. Based on the results of a recently completed drilling project undertaken by the Department of Natural Resources, seventeen coal exploration blocks which carry minimum work commitments will be offered to the New Brunswick Electric Power Commission on a sixty-day first right ofrefusal basis. Those blocks not taken up by the Power Commission will be offered under the same commitments to the private sector."

Jan 1, 1985