Search Documents

By Yoshihiro Kawarabata

INTRODUCTION The shield-driven method in Japan has been adopted widely in soft ground tunneling, namely, subway, water supply, sewer and utility tunnels, and recently this is an indispensable method in urban area. Since this method was started to adopt on a full scale from the beginning of 1960, construction achievements in length were about 830 km for 15 years until 1974 (1). According to the recent informations of the Japan Tunneling Association, the achievement in length under construction as of December, 1977, was about 350 km (2) and the extention of increase in shield-driven method can be guessed (Tab. 1). Tab. 1 - Achievement in Length by Shield-driven Method (As of December, 1977, Unit: m) (---): Achievement by Okumura Corporation [ ]

Jan 1, 1979

By Daniel H. White

Block caving, unlike most other conventional forms of mining relies principally on the natural forces within the rock mass to fragment and transport the ore. Obviously, not every orebody can be satisfactorily mined by block caving. In the early stages of mine planning an attempt should be made to assess the benefits of the block caving system relative to others, and develop a reasonable mining concept that may be used to provide preliminary information to mine planners and financial specialists. It is the intention of this paper to outline some basic geotechnical parameters that are essential to: 1) Assessing the feasibility of block caving an orebody and 2) Providing semidetailed information relative to mine design based on drill hole and other data.

Jan 1, 1979

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By Ralph B. Stevens

The objective of this 20-month program was to define the relationships between mine ventilation, temperature, humidity, ore properties, material's used in mine operations, etc., and the spontaneous combustion problem in underground metal mines. Tradeoff studies of availability, reliability, cost, and maintenance of spontaneous combustion protection sensors and telemetry were conducted, after which a prototype system was selected from four design alternatives. This selected system was then laboratory tested and demonstrated in an underground copper mine.

Jan 1, 1979

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By J. A. Kost

Contract H0242013 was originally to evaluate through underground tests, water spray systems for controlling respirable dust at the face of a longwall plow. A number of difficulties were encountered which made such an evaluation impractical. The contract was modified to evaluate, in the BCR dust tunnel facility, the live factors believed to affect respirable dust levels. A 60-foot long; plow face mock-up was constructed in the dust tunnel, a facility with controlled airflow and dust concentration. Six types of nozzles were tested with the following parameters: two nozzle orientations, two levels of water pressure, two levels of airflow, and with and without simulated airflow through the gob. Of these factors, the most significant in reducing respirable dust levels was nozzle orientation, where the nozzle directed 45 degrees downstream resulted in 27 percent lower dust levels than those directed 45 degrees upstream (against the airflow). Following in order of effectiveness were the higher water pressure and the lower airflow. All nozzles tested resulted in similar dust reduction, i.e., the type of nozzle was the least significant factor.

Jan 1, 1979

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979