Search Documents

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By M. Saidman, R. Pizzuti, R. Hirschfeld, A. J. Desai, J. Rand

Two bedrock tunnels, 170 to 250 feet deep and with a length of about 17,000 feet each, will be used to convey cooling water from the Atlantic Ocean to the Seabrook, N.H., Nuclear Power Plant. Seismic reflection and refraction surveys were used to obtain preliminary information about overburden and bedrock conditions. A major boring program, including core orientation and water-pressure testing, was undertaken to provide detailed geologic data. The results of the geotechnical investigation were summarized in terms of rock type, frequency and character of joints, degree of weathering, modified core recovery (RQD), pressure-test results and strength and hardness. These parameters were used as a basis for evaluating the feasibility of using a tunnel-boring machine, for designing and estimating the initial support systems, and for evaluating the grouting and tunnel lining requirements.

Jan 1, 1976

By Alfred C. Maevis

On October 27, 1972, ground was broken for the first section of the Second Avenue Subway, a two track underground rail system that was to extend from the south end of Manhattan at Broad Street, north to the Harlem River at 126th Street, a distance of eight miles. This ground breaking was the culmination of 67 years of planning for an east side subway in Manhattan. Following the successful opening of New York City's first subway on October 1904 there was a mass planning for additional subways throughout the City. In 1905 approval was requested of the Board of Estimate for a First Avenue route and Third Avenue route. The Third Avenue route was approved but when action was not taken to start construction, the approval in accordance with the conditions under which it was given was withdrawn. Further reports and plans for an east side subway, usually to be constructed on Third Avenue, were issued in 1920, in 1922, in 1924, etc. Those of us who had worked on the Sixth and Eighth Avenue subways in the thirites and early forties left to join the armed services of World War II in the expectation that we would return and start work on designing and constructing that east side subway. The reason that much of the thrust in those years was to construct on Third Avenue was that there was a Third Avenue "EL" and business interests of the City were in favor of its demolition. This demolition was accomplished in 1955 so one of the incentives to construct on Third Avenue was removed; but an east side subway was always part of the master plan of the City.

Jan 1, 1976

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Wayne R. Hopkins

Southern Arizona has one of the world's principal concentrations of copper ore bodies. Twenty miles south of Tucson, close to the Mexican border at Sahuarita in Pima County, is the Twin Buttes mine. In mid-1973, the Anaconda Company and American Metals Climax Incorporated (AMAX) established a 50-50 partnership to operate and expand the Twin Buttes property. Anamax Mining Company was established as the operating company for this joint venture. The production from the Twin Buttes mine is shared between the two partners who market independently. A major expansion of the Twin Buttes operation has included an accelerated stripping programrne for the pit, an expansion of the sulphide concentrator, the construction of an oxide leach plant and a 57 MW diesel generating power station. Part of this major expansion, the large tonnage oxide processing plant was brought on stream in 1975 and is now close to design capacity. The "mine to market gap" has been closed by producing high-purity copper cathodes at the mine site from oxide ore reserves. By using a hydrometallurgical process route, copper production is possible with negligible effects on the environment.

Jan 1, 1976

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By David E. Nicholas

Design of underground openings is becoming more critical as the mine deposits become lower in grade, initial investments increase, ore depth increases, additional safety regulations come into law, and increased ore recovery is required for conservation of minerals. Stability of these openings is dependent on the strength of the rock mass and the pre-mine stress field. The rock mass is composed of solid blocks of rock (rock sub- stance) and structural features (faults, joints, bedding, etc.). Methods of testing the rock mass strength are improving and be- coming more common, however it is difficult to justify the high cost of large scale testing for an initial mine design. An alternative to testing the rock mass is to measure the rock substance and the structural features separately, and then combine them to estimate the rock mass strength. The rock mass strength will vary depending on the orientation of the opening with respect to the structural features. The other factor affecting the stability of underground open- ings is the pre-mine stress field. Methods are available to measure "directly" the pre-mine stress in competent and relatively massive rock. These methods are costly to employ, therefore, they may not be justified in an initial study. The pre-mine stress field can be estimated based on the structural relationships formed from past tectonic events.

Jan 1, 1976

By Robert G. Lundguist

REAM is a unique and promising method of rock breaking using high energy, inert projectiles to impart mechanical energy to the rock. This paper describes a demonstration of the application of this new technology to two specific problems in open pit mining: secondary breakage and the scaling of loose material from pit walls. Under previous government contracts, Physics International Company developed the projectile impact method for a large variety of commercial and military rock excavation tasks. A 4 meter (13 foot) diameter by 16.8 meters (55 foot) long tunnel was driven at the Hope Valley Mine in the Sierra Nevada mountains of California in 1972 and 1973. An average of 1100 kg (1 ¼ tons) of a 172 MN/m2 (25,000-psi) granodiorite formation was broken by each of 590 shots used to drive the tunnel.l Based on these results it is estimated that REAM can drive over 60 meters (200 feet) of tunnel per day at about 88 percent of the cost of drilling and blasting. In addition, repeated axial impact by high energy projectiles was used to drill a 0.4 meter (16 inch) diameter horizontal hole in the same granodiorite formation. Each shot advanced the hole an average of 0.2 meter (8 inches).

Jan 1, 1976

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is fieldworthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

Coal mining in the Illawarra commenced in 1848. By the early twentieth century mining operations were spread over quite a distance along the coast centred on Wollongong. By this time there were already numerous tunnel mines and one shaft mine. Coal was first reported in Illawarra by Lieutenant Flinders on a voyage of exploration, southerly along the coast from Sydney in 1796. Because of the topography, particularly the escarpment and the narrowness of the coastal plain, access from Sydney was not easy by land and the normal access was by sea. It was not until some coastal areas had been developed for agricultural purposes that the mining of the seams on the South Coast commenced for the supp- ly of fuel. The most important mines in the early nineteenth century were Bulli and Osborne Wallsend. In general, coal was won from the tunnel mines and was transported directly, usually by tramway, to the nearest shipping point. Considerable hardship attended the earliest attempts at mining coal in regard to materials for mining and the way of life of the miners in the vicinity of the mines. With the growth of production and the installation of coke ovens at some mines the area, hitherto virgin bush- land, began to take on a more industrialised appearance. The mines were necessarily small,

Jan 1, 1976

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By Hemendra N. Kalia

The target to double the coal production by 1995 presents a formidable challenge to the coal mining industry. The mines of future, probably will be located in relatively difficult geological environment because of the exhaustion of the well defined bedded and easily minable deposits. To compound the problems of mining industry will be the reliance of power plants need for coal. The coal must reach the power plants on schedule to avoid expensive blackouts and brown¬outs. It will be imperative that the mines operate without interruptions and at designed capacities. The parameters which have been traditionally responsible for the interrup¬tions of production are: breakdown of production machinery, labor management relations and geological anomalies. Of these three problems, solutions for the first two can be arrived at by developing procedures to correct the situation. A planned maintenance and preventive maintenance program will go a long way in minimizing the equipment breakdowns. Labor relations will eventually improve as the miners begin to enjoy long-term employment. However, with the geological problems, the situation will probably continue to deteriorate and would require careful planning to minimize the impact of geological problems on production and safety. Some of the geological aspects which interfere with production are: faults, washouts, slips and slickensides, water bearing overlying strata, impuri¬ties in the coal seam, and presence of expansive clays in the coal floor. The design of large capacity mines will have to incorporate the geological distur¬bances and mine through them it may become very uneconomical to abandon producing sections because of the presence of the geological anomalies. This paper discus¬ses the geological aspects of coal mining which should receive consideration from the inception of the mining ventures. Pertinent geological aspects are discussed to develop the data base which will aid in evolving safe and efficient mine layouts.

Jan 1, 1976

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976