Search Documents

By Ted Nye

This paper describes a number of aspects of the design and construction of a driven tunnel which forms part of the Boggo Road Busway project. The driven tunnel is 430m long with an excavated width of 15m and a full tunnel excavation height of 8m. The first section of driven tunnel was excavated under the heritage listed Boggo Road Jail for a length of 120m. The main jail buildings and perimeter walls were built in 1908 and are of brick construction. Ground cover over the tunnel beneath the jail site varied from 5.5m to 8m and as a consequence the predicted settlement values and their potential to cause damage to the buildings were critical to determining and obtaining approval for the selected tunnel alignment. The geology along the driven tunnel alignment was very variable, providing mixed face tunneling conditions and ranging from surface residual soils to high strength rock at depth. The maximum ground cover above the driven tunnel is 20m.

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI's, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By Amalia Giannakou

When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and pointcloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion-point clouds with millimetric precision, capturing the structure of the rock mass. The automated point-cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors, such as site-specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using the Discontinuity Set Extractor (DSE) opensource software. Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time.

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN, ANMAYA NAIK, ASIF AHMAD, ADITYA PANDEY

Wet kata cooling power (WKCP) measured using a kata thermometer is a well-known heat stress index in mining industries. Although over the years several researchers have proposed different heat indices and indicated the limitations of the kata thermometer, it is still being used in many areas, especially in the South African gold mining industry, mainly because of its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for WKCP, and some of the more prevalent empirical expressions. The analysis presented based on a regression technique aims to assess the disagreement between model predictions and actual measurements. It is found that the WKCP expresses bioclimatic interaction quite well under the specific parameter of interaction that explains the harsh thermal environment and air condition, such as metabolic activity, the person’s clothing, and the velocity of the air in which the person is working. The statistical analysis shows that the WKCP exhibits significant estimates to thermal stress under lower air velocities, light clothing, and higher metabolic activity rates.

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By G. P. JADAUN, ANINDYA PAIN, Aditya Rana, SAURAV RUKHAIYAR, N. K. Bhagat

This study compares three different techniques — decision tree, artificial neural network (ANN) and multivariate regression analysis (MVRA) — for predicting blast-induced ground vibrations in some Indian tunneling projects. The models’ performance was also compared with site-specific conventional predictor equations. A database consisting of 137 vibration records was randomly divided into training and testing sets for model generation. The results indicate that the decision tree is best suited to predicting vibrations. Furthermore, the decision tree suggests that the intensity of near-field ground vibrations is mainly affected by the total charge fired in a round, whereas the intensity of far-field vibrations is governed by maximum charge per delay and charge per hole.

By DFI DFI

An Online Conference

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By Robert L. Chufo

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of "seeing into the earth." A first generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full threedimensional (3-D) imaging system that will have applications in both the underground and surface environment.