Search Documents

By C. McAllister, D. Preece, J. Berendzen

"The Multiple Blasthole Fragmentation (MBF) model models multiple explosive charge contributions and the effect on fragmentation of delay timing with its associated scatter for each blasthole. The model uses near-field blast vibration attenuation parameters and the ground p-wave velocity as inputs for part of the in situ rock property to model rock fragmentation. It models most blast design parameters explicitly and simulates the effect of wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges within a blasthole or among blastholes. The fragmentation size is calculated at three-dimensional grid points within a blast, and the fines and oversized blocks are treated explicitly. The model takes a surveyed irregular geometry of the free face of a blast as the calculation boundary.This paper presents a case study on applying the MBF model at an openpit mine. Near-field vibration measurements from signature hole blasts were conducted to obtain the stress-wave magnitude and attenuation parameters as well as ground sonic velocity. A production blast was then monitored with the corresponding fragmentation measured, serving as site-specific inputs to the MBF model. Various blast design scenarios were then simulated to develop ones that provide better fragmentation to improve mill throughput for the mine. IntroductionThe semiempirical fragmentation models currently found in the literature (Cunningham, 1987; Lownds, 1995) cannot explicitly model contributions from multiple blastholes with varying delay intervals. Most of these models are not three-dimensional. Furthermore, these models predict an average fragmentation size within a volume surrounding a blasthole and use the average size to generate a size distribution over the volume. The percentage of fines and oversize blocks is included in the distribution. Typically, such models are inadequate for predicting fines and oversize blocks (Cunningham, 1987)."

Oct 1, 2016

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By J P. Sykes, A Trench

"The common-held view of the future of copper mining is one of declining quality of mineral resources and increasingly limited long-term development options. This decline, in turn, is viewed as inevitably leading to increasing economic, socio-political and environmental costs. As a result, new technologies and innovations will be required to mitigate cost escalation. The future is therefore typically summarised as a battle of a ‘below-ground’ declining quality asset base pushing costs upward versus ‘above-ground’ technology and innovation driving costs downward. The role that high quality new mineral discoveries could play in mitigating industry cost pressures is typically understated, if considered at all. New high quality discoveries can be mined at lower cost than existing assets and potentially if discovered in the right locations within a more amenable contemporary environmental and socio-political setting. Such deposits, once discovered, would improve the overall quality of the industry asset base, as well as benefitting their owners substantially through higher margins. However, to target new high quality deposits explorers need some understanding of the nature of high quality copper mines in the long-term future. Conventional scientific and economic techniques for analysing the future of copper supply, generally by studying the project pipeline, ignore as yet undiscovered resources and also struggle to fully incorporate the multiple internal and external factors that could impact upon copper mining practices in the future.Scenario analysis is specifically designed to consider multiple factors interacting in the future, and is thus more creative than simply looking at the visible project pipeline. The use of scenarios is therefore potentially capable of providing insight into aspects of the future of copper mining about which little is currently known or that remains considerably uncertain. In this study, the Oxford University Scenarios methodology was employed to analyse different plausible futures for copper mining and the consequent implications for exploration targeting strategies. The scenario analysis highlights two key dimensions or axes that serve to map out potential industry futures: firstly the technical and economic optimisation of the existing industry; and secondly the generation of new prospects or ‘search space’ for the copper industry. These two axes in turn frame four different scenarios for the future of the copper mining industry. These copper mining scenarios are then compared to the 20 largest existing copper mines and projects, and their owners, to determine if any represent an appropriately robust exploration targeting proxy: none do. The paper therefore concludes that efforts by industry are required to generate mine concepts that would be viable across all scenarios, and thus act also as exploration targeting proxies. In the interim, companies will have to seek to build portfolios that create an overall robust asset base, out of individually less robust assets. Failure to do this implies that consequential, irreversible strategic decisions lie ahead for the copper mining industry, which may be a threat to both incumbents and the very industry itself. This situation makes strategic exploration targeting in the copper industry very difficult.CITATION:Sykes, J P and Trench, A, 2016. Using scenarios to investigate the long-term future of copper mining and guide exploration targeting strategies, in Proceedings International Mine Management Conference, pp 265-290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By S P. Young, K R. Monro

Reducing metal prices have forced mining operations to become more efficient and innovate in order to do more with the existing base. Much of this effort has focused on improving the efficiency of load and haul operations. The key to this is to understand and quantify where delays and missed opportunities exist. Metrics such as utilisation of availability, efficiency utilisation and asset availability are helpful indicators of performance; however, uptime-based time usage models and performance analysis tools using productive operating time models help to identify additional improvement opportunities.Phu Kham is a copper-gold mine operated in the Lao People’s Democratic Republic (Laos) since 2008 by PanAust Limited. The mine is a single large open pit of 450 m depth, running a fleet of 51 100 t class rigid dump trucks and 300 t and 200 t shovels controlled with the aid of a fleet management system in order to achieve ex-pit material movements of 56 Mt/a.Commencing in late 2014, a range of initiatives were implemented in order to improve the efficiency of the mine haulage fleet. These include hot seating of all operator changeouts via changeout ramps, split shifting of crews to minimise queuing delays, maximising blast volumes and minimising blast event days to reduce blast exclusion delay events including opportune refuelling of equipment during blasting events, inspections of trucks during refuelling events, implementation of a dedicated haul road services team to help reduce wet weather related delays and infrastructure development for haul path efficiency improvements.These and other initiatives have allowed the mine haulage fleet utilisation of availability (UofA) to be sustainably increased from 85 per cent to 97 per cent (see Figure 1), efficiency utilisation to increase from 85 per cent to 90 per cent, and productive operating time (POT) to increase from 73 per cent to 84 per cent. The corresponding increases in efficiency of the haulage fleet has allowed an equivalent reduction of eight haul trucks from the fleet to meet continuing life-of-mine production requirements.CITATION:Monro, K R and Young, S P, 2016. Truck haulage improvements at the Phu Kham mine – the journey to 97 per cent utilisation of availability, in Proceedings International Mine Management Conference, pp 339-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

"2016 marks an amazing accomplishment in the mining industry as Hecla Mining Company celebrates its 125th anniversary. Mining Engineering sat down with Hecla chief executive officer Phil Baker to gain insight on this tremendous longevity and to get his view on how the company demonstrated persistence, gained perspective and created position for its future.How did Hecla Mining Co. get its start?In 1891, a group of investors formed Hecla Mining Co. to acquire and trade mining claims. No one envisioned at the time that the Coeur d’Alene Mining District would become known as the “Silver Valley” and produce more than 37.2 kt (1.2 billion oz) of silver. Or that Hecla would become the United States’ largest primary silver producer and the last of the pioneer mining companies from this illustrious mining district.What is the origin of the name “Hecla?”That will forever be a bit of a mystery. Some say it was named for an Icelandic volcano. Or that it was the foresight of James Toner, who staked the original claim, that it would go so deep, fulfilling the medieval folklore definition of the word ‘Hekla’ which is the ‘Gateway to Hell.’ I kind of like that one as the Lucky Friday Mine is almost 3.2 km (2 miles) below the surface. It has operated for more than 70 years and has all the markings of being one of only a handful of mines that will exceed 100 years of operations.Is there a common theme, or thread throughout the 125 years?Yes, Hecla has always had a solid core of high-quality and long-lived assets, positioning the company to survive times of low prices and reap the rewards when cycles turn and higher prices are realized. But it is not just assets. Hecla has extraordinary expertise that gives us the perspective of how to acquire, explore, develop and operate mining assets, particularly underground. Hecla is one of the few companies to acquire assets in the last five to six years and we did not have to write down the value of them, which means we paid a fair price for the asset despite the metals price reductions that followed the purchase. And our culture has given us the persistence to develop mines and complete projects despite lower prices. For almost a decade we have been advancing the #4 Shaft project at the Lucky Friday. We will complete this project this year, positioning the mine to operate for decades. We have elected to spend capital on San Sebastian (Durango, Mexico) and Casa Berardi (La Sarre, Quebec, Canada) to start a new mine and increase production, respectively. And we are spending money on new techniques, new equipment and innovations to our operations. Our insistence is on developing for the future, and our persistence in doing so is in contrast to many companies that are reducing investment and shrinking production"

Jun 1, 2016

By Lance Rasband, Richard Hanke, John Starcevich

"Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m (14.9-ft) thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal m (400 ft) of jet grout improved soil at a rate of slightly more than 1.6 m/d (5.3 ftpd). It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s second largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m/d (36 ftpd). By the end of October 2013, Bertha had mined roughly 131 m (430 ft), averaging 1.4 m/d (4.7 ftpd), and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m (800 ft) mark and Bertha was averaging 3.6 m/d (11.9 ftpd), achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on Dec. 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm (0.9 in.) diameter monitoring well casing, previously installed by the Washington State Department of Transportation (WSDOT) to monitor groundwater conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jun 1, 2016

By Steve Karl

"The International Tunnelling and Underground Space Association (ITA) held its 42nd General Assembly along with the 2016 World Tunnel Congress (WTC) April 22-28 in San Francisco, CA. The event was co-organized by the Underground Construction Association of SME (UCA). This was the first time the event has been held in the United States in 20 years.As cities demonstrate strong needs in tunnels and underground spaces for public transportation, subway stations, hydroelectric infrastructures and other underground infrastructure needs, the WTC 2016 provided the 2,319 attendees from around the world a unique occasion to discover the latest state-of-the art innovations in urban planning and underground construction projects in the United States and worldwide.The Congress, held in lieu of the UCA’s North American Tunneling Conference, included an exhibit that attracted 226 exhibitors in 298 booths. The exhibit had on display the latest in technical equipment and services from some of the largest and best companies in the international tunneling industry. The exhibit hall was also the place where participants were able to interact with the authors of the 168 posters and receive answers to various topics directly concerning civil engineers: innovative procurement processes, cost and risk management, contractual methods, BIM technologies and examples of innovative underground infrastructures built worldwide. And the technical program included 353 technical presentations – 185 podium and 168 posters.What is ITA?ITA-AITES is a nonprofit, nongovernmental organization that promotes greater use of underground space as a key instrument in sustainable development. Established in 1974 and based in Lausanne, Switzerland, ITA-AITES is made up thousands of professionals involved in the tunnel and underground space industry, including engineers, project owners, town planners, architects, industrial designers, companies specialized in public works and major structures, suppliers of construction site facilities and equipment, lawyers, politicians, researchers and academics, economists, financial experts and other stakeholders.ITA-AITES consists of 73 member nations and 300 affiliated members, including 15 major sponsors and 60 donors. The association is run by an executive council made up of 15 members elected by the 73 member nations, each representing a different dimension of the tunnel community."

Jun 1, 2016

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Flatten, F Reusch

Recent advances in the disciplines involved in simulating large mining operations provide increasingly precise and accurate methods for the study of cave mechanics; however, in large regional-scale models, hydrological aspects are often neglected or studied independently from the mechanical problem. There exists a great demand for a unified approach to study and simulate both the mechanical and hydrological phenomena that allows for a more detailed understanding of the effects of groundwater flow, dewatering and the impact on block cave mining operations.This paper presents a numerical framework that combines three-dimensional regional-scale hydrological simulation techniques for groundwater flow, together with non-linear continuum–discontinuum rock mechanics models, provides such a unified modelling approach. The underlying simulation technique is based on a coupled parallel solution formulation adopting single-phase fluid flow formulations into a discontinuous, strain softening and dilatant finite element model. This approach is adopted for the presented case study of a realistic block caving example in a simplified unidirectional coupling formulation, to investigate the effects of the mechanical analysis on the hydrological response. Here, particular emphasis is on the non-linear coupling of the deformable and strain-softening solid skeleton and fluid phase; eg the change of hydraulic properties with evolution of damage in the rock mass and large-to-intermediate scale structures due to ongoing caving operations. The importance of discontinuum structures is discussed, as mining-induced fault reactivation significantly influences the hydrological response.CITATION:Flatten, A, Reusch, F and Beck, D, 2016. The application of hydromechanical mine-scale modelling for large block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Talu, E Savage, S Howe

Major falls of ground, strainbursts, airblast and mudrush events are the major hazards in block caving environments, resulting in both safety and financial consequences and losses. Rio Tinto mines have developed strategies to reduce the likelihood of these events occurring. However, until recently, there have been no tools available to monitor and manage these hazards in real time.Mira Geoscience and Rio Tinto have collaborated to develop real-time geohazmaps to monitor and manage major cave hazards. These geohazmaps are used by mine planners to integrate multiple hazard parameters that contribute to form a combined hazard rating.The benefits of implementing geohazmaps include safety and cost improvements through the early identification of potential locations for major events. These cost savings are realised in the design phase, where development and critical infrastructure is located in areas of lower hazard rating. Additional improvements can be achieved by taking the hazard level into consideration when planning the production and development schedules and ground support design.CITATION:Talu, S, Savage, E and Howe, S, 2016. Geohazmap implementation in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 817–822 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016