Search Documents

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By Paolo Prevedini, Antonello de Risi

"The city of Naples has one of the most ancient traditions of tunneling in the world, since Roman age until today. This was due to the softness of volcanic rock covering most of the city surface, this determined in centuries the excavation of many connected cavities, today still accessible. The building of metro lines promoted industrial tunneling construction: TBM, Raise Boring Machine, Vertical Shaft Machine and freezing technologies played a decisive role facing water pressure near the sea. MNspa is an advanced constructor with two lines built in parallel, mainly underwater. The planning of this infrastructure has been upgraded with the projects of international architects from all Europe, with installation of art masterpieces in station spaces while archeological excavations revealed artifacts since Paleolithic. The city expects to give a new image of the urban landscapes within the completion of all stations and consequent rehabilitation of interiors and external city spaces. A case study of Municipio square station, is chosen to explain the relevance of archaeological research in improving and developing the projects of Line 1 stations. In these pages, it will be explained how the engineering process required to deal with Art, Architecture and Archaeology to finally realize an extended urban renovation of Naples. 1 CITYSCAPE 1.1 Introducing the geological history of Naples In the evolution of the city, capital of the Magna Graecia and of consequent kingdoms, a new layer of buildings was added over the foundations of demolished walls of the precedent domination period: from the top of the Bourbons layer (the most common scenery of the city since 1734) to the Aragonese layer found just underneath it; then below stands the Angiovin city, which in turn is built above the Swabian traces; underneath the ancient traces of the Byzantine age are found just above the extended Latin age layer. The most ancient settlement, known as Parthenope, dates back to 1500 b.C. It sits below the Greeks remains of the city of Palepolis, which had been rebuilt under the name of Neapolis by Romans."

Jan 1, 2016

By Larry L. Snyder

A compact 4.87 m (16 ft) diameter tunnel boring machine (TBM) is capable of boring a 12.2 m (40 ft) radius curve while gripping horizontally, or vertically, as may be required for the excavation of turnouts. The machine's 5.0 m (16.5 ft) length and a patented machine structure allows steering while boring without causing harmful eccentric loads. An extremely stiff thrust system, rigid front and rear grippers, and the torsional stiffness of a front end electric cutterhead drive combine to create superior machine stability and boring efficiency. A 2.2 m (7.2 ft) diameter prototype, complete with a soft ground shield attachment, was used successfully on a tunnel project in Scotland.

Jan 1, 1989

By Theodore H. Budd, Austin M. Cooney

The paper discusses the background and theories of the conditions that led to the settlement of a Lovat TBM mining in an earth pressure balance mode on a recent project in Milwaukee, Wisconsin. The settlement occurred independent of human error and caused the cost of the project to increase 50 percent. The project was mined in the highly congested downtown area in alluvial and estuarine deposits, 7.6 m below the water table with a prescribed contract requirement that precluded dewatering in deference to concern for foundations of adjacent existing buildings.

Jan 1, 1989

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By J. Andrew McGlenn, Greg Emslie, Murray Gant

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet a growing population’s longterm needs. It includes a bored tunnel between two deep shafts located in North Vancouver and Burnaby, BC, Canada. The support of excavation for the 16-meter-diameter (52.5 ft) TBM launch shaft consists of 83-meter-deep (272 ft) unreinforced concrete slurry walls. This paper discusses challenges encountered during construction of the launch shaft slurry walls, namely excavation methods and slurry loss, and mitigative solutions implemented to successfully complete the shaft with minimal impact to project schedule.

Dec 1, 2022

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

"There is no fast way to add more than 6.4 km (4 miles) of track, most of it underground, to the Sound Transit Link Light Rail system in the Seattle, WA area. But increasingly busy traffic through a number of neighborhoods made it necessary. That’s the challenge a joint venture of several tunneling contractors faced when starting its portion of the $1.9-billion Northgate Link Extension in 2013, and the project is still keeping it busy three years later. Completion will mean just a 14-minute ride from Northgate to downtown for an extra 60,000 passengers by 2030. The transit lines will join 57 km (36 miles) of new and under-construction light rail lines running north, east and south from Seattle.Voters tired of long commute times approved the project, a key part of Seattle’s regional mass transit system, in 2008. The extension is part of a plan adopted by the Sound Transit board in 1996 to connect the region’s major activity centers. The Northgate project is meant to relieve one of the area’s most congested traffic areas by connecting the Northgate, Roosevelt and University District neighborhoods to existing routes including downtown Seattle and SeaTac airport.Sound Transit dedicated more than a quarter of the project’s estimated expense — $440 million -— to general contractor JCM Northlink LLC to handle the tunnel segment. JCM is a joint venture formed in 2013 between Jay Dee Contractors of Livonia, MI, Frank Coluccio Construction of Seattle, WA and Michels Corp. of Brownsville, WI. The contractors regularly collaborate on large-scale projects and brought experience working on a different section of the extension they completed in 2013.JCM project leaders knew immediately that the schedule would be demanding. They had to work around the clock six days a week to meet deadlines. The extension runs through highly populated areas, meaning contractors had to follow strict city noise restrictions between 10 p.m. and 7 a.m. Plus, supervisors needed to manage the scheduling of nearly 250 employees to keep work running smoothly.“We had eight different operations and four different subcontractors trying to work in one tunnel,” said Chris Wood, JCM site project superintendent. “It’s important that we keep work linear. That’s the biggest challenge: keeping a path in and out so you can pour concrete, keep electricians and carpenters going, and accomplish everything else.”"

Dec 1, 2016

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By Hongjie Yu, Rakshith Shetty, Claudio Cimiotti, Nick Karlin, Mike Mooney, Vitaly Proshchenko, Matt Kendall

This paper documents an effort to explain cutterhead torque behavior observed during slurry pressure balance TBM tunneling through soft ground on the Los Angeles Clearwater project. AI machine learning and mechanics model-based learning was used to characterize cutterhead torque behavior including the TBM operating and ground parameters that influence cutterhead torque. Also, key parameters were from the slurry circuit data, including fines content, in-situ density, pore water fraction and solids content were included. The paper details what was learned using these new data-driven approaches as well as limitations with AI machine learning.

Jun 23, 2024

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By A. Bhargava, V. Nasri

Traditionally, secant piles have been utilized to provide temporary support during excavation for shafts and cut-and-cover tunnels. As an alternative, the secant piles can be included into the permanent structure, where they serve as the envelope sustaining the lateral loads and gravity of the permanent structure in addition to supporting the excavation during construction. This has several benets, such as shorter building times and lower excavation costs. Recent construction of an approach structure and an underground station as part of Montréal, Canada’s Réseau Express Métropolitain (REM), one of the biggest transit systems in North America, was completed with remarkable success using this. In this paper, a case study based on a project that employed secant piles as the permanent liner is presented. Techniques to guarantee a watertight construction with over a century of service life are described, along with a variety of structural and waterproong methods applied to create an economical design.

Jun 23, 2024