Search Documents

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By E. D. Gradner

During 1924 a number of lives were lost and other men incapacitated by the toxic effects of gases produced in blasting in massive sulphides. In one mine, three men working in a raise were caught by gases from blasting a drift round in massive sulphide on the level. The round in the drift was shot ahead of time and it was necessary for the three men to travel through the gases to the intake air course. Two of the men lost their lives, and the third was injured, apparently for life. Other men at this same mine have been caught in the gases at blasting time and seriously injured. At a second mine, the gases from blasting in sulphides appear to be very dangerous, and it was necessary to send a number of men who were caught in such gases to the hospital. One man who was seriously gassed has not recovered in over a year is time. Another man similarly gassed soon died of influenza.

Jan 1, 1926

By Albert J. Kritscher

The Similkameen Copper Project located near Princeton, British Columbia, is operated by the Similkameen Mining Company Limited, a wholly-owned subsidiary of Newmont Mining Company. The orebodies for this project are located on both sides of the Similkameen River for which the project is named. The project involves the processing of an average of 15,000 STPD of andesitic ore, mineralized largely with Chalcopyrite, at an overall plant availability rating of 90 percent. Project life is nominally 15 years. Design for the plant and its ancillary facilities was undertaken by Bechtel Corporation with procurement and construction management by Canadian Bechtel Limited. Construction began in June 1970 and first ore was introduced into process in March 1972. This paper concerns itself only with the project tailing system. The processing plant is located on a bench of glacial stream gravels which overlooks the river canyon. This site represented the only relatively flat area of sufficient size to accomodate processing facilities near to the ore- bodies. Reference is made to Figs. 1 and 2 showing the relationship of project features in plan and profile.

Jan 1, 1973

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By David R. Jessey

This volume contains the detailed mine site reports written by the WAPORA, Inc. and KETRON, Inc. staffs. It is a companion Appendix Volume to Control of Water Pollution from Surface Mining Operations. Copies of this report are maintained on Open File at the U.S. Bureau of Mines Research Center, Spokane, Washington.

Jan 1, 1981

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By Pedro Alejandro Samané Tuni

El presente texto describe la metodología de investigación adecuada para la excavación subterránea a través de la clasificación geomecánica según: RMR (Bieniawski), Q (Barton), Romana, Deere y Palmstrom, quienes determinan los tipos de sostenimiento y el span de autosoporte para cada tipo de roca e influyen en el método adecuado de excavación según clasificación de excavabilidad. Sin embargo, no se encontró el método adecuado y solo se define cuál de estas clasificaciones son factibles de usar en la excavación de cada tipo de macizo rocoso.

Jan 1, 2016

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969