Search Documents

By Richard Crawshay, Duncan Hutchison

Continuous Mining Systems Limited have developed an efficient, high-capacity, in-line loading unit capable of handling shot rock in tunnel driveages at extraction rates up to 970 tonnes (1,000 tons) per hour. A smaller 408 tonnes (450 tons) per hour loader is also available These in-line loading units called "Osciloaders"® provide a continuous flow of material from the muck pile to an anciliary conveyance eliminating the cyclic or interrupted movement noramlly associated with gathering arm or bucket type loaders. The osillating lip fluidizes the material, reduces the penetration force required and facilitates and regulates the material flow onto the adjacent conveyor. The conveyor is wide and accommodates very large material with ease, transporting and elevating it to a height suitable for a waiting conveyance at the rear of the machine. The "Osciloader"® is currently being utilized for production mining by a major company in Sudbury, Ontario. Both truck and conveyor anciliary haulage are being utilized. The paper describes the development of the loader and how it may be applied in tunnelling applications.

Jan 1, 1987

By Carl Barchet

INTRODUCTION Located on the Colorado River on the Nevada-Arizona border about 56 km (35 miles) southeast of Las Vegas, Nevada, Hoover Dam is a gravity arch dam 221 m (726') high for electric power generation and water supply. The head waters of the dam form a large reservoir, Lake Mead. The dam is equipped with two emergency spillways, one in the Nevada abutment and one in the Arizona abutment. Both spillways which are concrete lined and 15.25 m (50') in diameter, were intended for use only if Lake Mead is full and incoming flow of the Colorado River exceeds the discharge capacity of the turbines and regular bypass conduits. In the spring of 1984, a combination of rain and unusually rapid snow melt required the opening of the spillways for only the second time in the 50 year history of the dam. As in the previous use in 1942, the massive discharge of water through the tunnels resulted in severe damage to the concrete Linings of both tunnels. This damage is the result of cavitation which occurs as the discharge water flows at very high velocities over minor irregularities in the concrete lining. The U.S. Bureau of Reclamation has long been aware of the cavitation effect which occurs during these high volume discharges and has been studying solutions. One solution to the problem is to induce air bubbles into the flowing water to eliminate the vacuum associated with cavitation. This solution had been implemented at Yellowtail, Flaming Gorge, Blue Mesa, and Glen Canyon dams by constructing an aeration slot in the inclined portion of their spillway tunnels. Since the spillways of Hoover Dam were already in need of repair, the BUREC decided to construct similar facilities in each of the two 15.25 m (50') diameter spillways coincidental with the other repairs required.

Jan 1, 1987

By Palmer King

The increased emphasis on environmental protection, together with the exorbitant costs, or in many urban areas the complete unavailability of surface space, has resulted in a burgeoning demand for greater use of underground space. More and more, those considering new or expanded facilities are looking toward the possibility of utilizing underground space for communications installations, for transportation of people, industrial products, water, sewage and energy, and for industrial installations. Happily, this growing demand for use of underground space is accompanied by fast forward strides looking toward more efficient underground excavation techniques. The tunnel boring machine is already here and where ground conditions are suitable for its use it can greatly reduce the cost of underground excavations, savings of one-third or more often being realized. Research is underway involving excavation by use of laser beams, jetting, vibrations, improvement of tunnel boring machines to make possible the excavation of harder rock, and other advanced techniques. The Engineering Foundation estimated in 1973 that tunneling costs can be reduced as much as 30 percent by rapid excavation methods which are expected to be developed through ongoing research programs in the next few years. Your American Society of Civil Engineers reported in 1973 that $60 billion per year, or 15 percent of the gross national product, could be saved if facilities required to support life were located in the subsurface. Studies looking toward improved contracting practices are going on under the sponsorship of the National Academy of Sciences, and Mr. Al Mathews who is heading this program will address you during this session on the status of this project. I myself am a member of Mr. Mathews' study group and, considering the human element involved, it is too early to make predictions as to what can be accomplished in the way of savings in costs of

Jan 1, 1974

A description of:1. Air-lock at No. 14 Upcast shaft.2. Pit-top gates at Dudley winding shaft.3. Safety rider employed in sinking No. 18 shaft.1. AIR-LOCK AT No. 14 SHAFT.Some time ago it became desirable to raise and lower the McBride tunnel men to save them walking the inclined tunnel, about a mile in length, with a dip of nearly 600 ft., and a maximum gradient of 1 in 4. The main Upcast shaft, No. 14, was, therefore, equipped for winding the men. As this shaft was the main ventilating shaft for the McBride tunnel mine, it was necessary to take the greatest precautions against leakage of air. The writer therefore devised the concrete structure shown in Plate 1.The structure, as shown, surrounds the shaft inside the poppet legs. As the men are wound on double-decked cages (twelve men to each deck) provision is made at both top and bottom for the two decks to be loaded and emptied simultaneously. The doorsover the sky shaft, shown in the drawing, have been cut out and the sky shaft has been close-timbered with a double layer of T. and G. flooring boards, with building paper between, nearly up to the thimble frame, a small hole only being left for the winding rope topass through. The space between the ramps is glazed with plate glass to allow the winding-engine driver a good view of the pit top.The men are wound from two levels, 302 ft. and 611 ft.2. PIT-TOP GATES AT DUDLEY WINDING SHAFTTo minimise the shock to cage, couplings and rope when winding quickly, the writer devised the apparatus and arrangement shown in Plate n.

Jan 1, 1928

By W. H. Hoffman

During the autumn of 1891, several heavy blasts (each throwing down some 3000 tons of ore) were made on what is known as the Theall side of these mines. Immediately after one of these blasts, the writer found that at least one-third of the ore was largely impregnated with pyrites, and besides this, fully 15 per cent. of the entire blast was composed of irregular lumps of magnetic pyrites. This was a revelation wholly unexpected, as previous examinations by many experts had failed to disclose any such quantity of sulphury ore. Over the center of the Theall tunnel there suddenly appeared a perfect keystone, as it were, of pyrites, 3 feet wide at the arch of the tunnel, 13 feet ride at the top, and 20 feet high. This keystone pinched out in February, 1892; but in that month large blocks of pyrites were more plentiful on or near the western wall, and these deposits extended the entire height of the workings, some 43 feet. The second blast in November, in the face and over, and on each side of the tunnel, was far more surprising. The whole cross-section it exposed was thickly interspersed with layers of magnetic pyrites, ranging in thickness from 10 to 24 inches, and quite irregular in form, while all of the ore carried much more than the usual amount of sulphur in the non-magnetic pyrite. One hundred and fifty-five tons from a portion of this breast (western side), showed the following composition upon sampling and analysis: Per cent. Metallic iron,...45.080 Phosphorus,..........304 Sulphur,...........23.510 And the balance of the blast showed: Per cent. Metallic iron,.....• 33.210 Phosphorus,...........349 Sulphur,.......... 6.680 vol. xxI.-33

Jan 1, 1893

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

By James J. Brady, James S. Lewis, Robert B. Gordon, Jimmy W. Honeycutt

INTRODUCTION Tunnel construction has always been an extremely high risk form of contracting primarily due to the inaccessability of information concerning the ground conditions to be encountered during excavation. We certainly make every effort to overcome this problem through borings, geological research, site visits, etc.; but at best owners, engineers and contractors alike are only able to interpolate a relatively small amount of factual data from isolated sections of the project into a forecast of ground conditions for the entire project. In essence this becomes an "educated guessing game" with risk to reward ratios (and subsequently the bid price) in direct relationship to the contractor's confidence in the quality of the guess. In many instances it is economically or physically infeasible to obtain information and of course the total picture is never known until the project is complete. This problem effects the contract format as well as price. The contractor's ability to handle unforseen problems on the project become extremely important as to the project's overall success. The following pages contain an actual case history of a project which affords an excellent example of the entire spectrum of situations resulting from tunnel construction in difficult ground conditions.

Jan 1, 1983

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By Frederick H. Parkinson, Joseph Fernandez, David E. Westfall

The April 13, 1992, flooding in the freight tunnel network under the city of Chicago had a profound effect on the nearby Chicago Transit Authority (CTA) subway service. This paper provides an overview of the evaluation techniques, mitigation measures, and water control efforts used to maintain the integrity of the subway tubes. Specific topics discussed include visual inspections, inflow monitoring, structure and soil testing and sampling techniques, and the development and implementation of chemical and cementitious grouting programs.

Jan 1, 1993

By M Grinceri

The New MetroRail City Project was completed in 2007 in Perth, Western Australia. The project included construction of two underground stations, twin bored rail tunnels of 1.4 km combined length and cut-and- cover tunnels and dive structures of about 1 km total length. It is the first major underground construction project within the Perth central business district (CBD). This paper provides an introduction to the project and describes the geology and hydrogeology of the area. Ground conditions varied significantly along the alignment from soft estuarine muds in an area of reclamation to very dense cemented sands and very stiff to hard clays. Deep foundations for the project extend down into the bedrock below the CBD, a Tertiary siltstone/sandstone. Key geotechnical hazards encountered during the project are discussed. The building protection methodology on the project is described, including damage assessment, condition surveys, monitoring and protection of key structures.

Jan 1, 2008

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By George A. Hoffman, Richard J. Proctor

INTRODUCTION We will discuss here only the subway construction phase; that is, two to five years at a given location--not the long-term analysis. We also will compare some tunnel construction methods used for BART and in Los Angeles. Typically, urban planners and engineers try to balance a new mass transit system to include tunneled subways, cut-and-cover construction in city streets, and elevated guideways. Their decisions are based on many factors, most of which can be quantified. But there are some socio-economic-environmental factors which are almost intangible, or nonquantifiable, and these are rarely included in the final report for a rapid transit system. There are two reasons for this: First, it is difficult to evaluate disruptions and psychological inconveniences to individuals and to the community during the construction period, and even more difficult to assign costs because the valuations are always subjective. Second, the rapid transit project capital costs are given in the final report and the public knows them; but the intangible social costs are borne by the affected neighborhood community, not the entire city, and as such they are "hidden costs," which in fact may add as much as 25 percent to the total system cost.

Jan 1, 1974

William Kent, New York, N. Y.:—The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is an admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly gives the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer—Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, Sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer—Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric transmission, electric smelting. Work of the Chemist and Metallurgist—Explosives, chlorina-tion, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist—Economic geology. Work of the Mining Engineer—Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing those things he was trained to do as a specialist, but in making use of the knowledge of geologists, chemists, and electrical and

Jan 1, 1910

By D. Harrington

The mining industry of the United States has-long been severely criticized because of its high rate of accident occurrence, net only as compared with other major industries-in the United States but also with the mining industries of other countries particularly Europe. Statistics (often not of strictly comparable nature) indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These figures are by no means comforting to humanitarian mining men, irrespective of their status in. the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. This picture becomes much darker when the above statistics are augmented with data indicating that. on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar types of mines in Europe, particularly England and Wales, Belgium, France, and Germany. However, these foreign accident statistics should be carefully analyzed before we become very mush concerned about them, because they are clot strictly comparable owing to several considerations, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions axe definitely dissimilar to ours in many if not most phases, and numerous ether factors affect the comparability of foreign mine-accident statistics with ours. Unquestionably it should also be taken into consideration that the accident rate of the 130,000,000 or more constituting the populace of the United. States as a whole is much higher than that of any other major country in the world and is two, throe, or more times the rate of the European countries that have more favorable mine-accident rates than those of the United States. Moreover, it is significant that the mine-accident-severity- rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little mere, favorable than the comparable figures in the United States, namely, that mining-has an accident-severity rate about seven times that of the average of about 30 of the major industries of this country.

Jan 1, 1941

By Charles W. Perdue

This U.S. Bureau of Mines report considers, from a psychological perspective, the perceptual process by which miners recognize and respond to mining hazards. It proposes that if the hazard recognition skills of miners can be improved, mining accidents may be reduced to a significant degree. Prior studies of hazard perception in mining are considered, as are relevant studies from investigations of military target identification, pilot and gunnery officer training, transportation safety, automobile operator behavior, research into sensory functioning and visual information processing. A general model of perception is introduced, and selected concepts from the psychology of perception that are applicable to the detection of mining hazards are reviewed. Hazard recognition is discussed as a function of the perceptual cues available to the miner as well as the cognitive resources and strategies employed by the miner. The development of expertise in responding to hazards is related to individual differences in the experience, aptitude, and personality of the worker. Potential applications to miner safety and training are presented.

Jan 1, 1995

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

A concept gaining attention among rock mechanics researchers in studies of soil-structure inter- action is the use of compressible packing between the structure such as tunnel lining and the soil or rock. Lester H. Gabriel, provided information about work on this concept at the II Symposium on Rapid Excavation, October 16-17, 1969, Sacramento State College, Sacramento, Calif. It is well-known that loads transmit their effects to those locations which deform least. Traditionally, the question to be answered by the structural engineer is how rigid the structure ought to be. The stronger the structure, the more resistant it becomes to deformation. If it is more rigid than the surrounding strata, the structure acts as a pillar, focusing load on itself. However, if the structure is less rigid than the surrounding strata, blocking or packing between the structure and the enclosing material facilitates the formation of soil or rock arch. The object then is to design and build structures such as tunnel linings, which harness the advantages of carefully planned small movements. Tests on plaster cylinders imbedded in granular sand and loaded were compared to those of plaster cylinders protected in sheathing of polyfoam rubber. The compressible sheath permitted support of up to ten times greater loads Gabriel, Lester H., "Principles of Soil-Structure Interaction Applied to Tunnel Linings." Hecla Mining Co. has successfully used shotcrete with substantial cost savings for ground support purpose. To date, the use of shotcrete in Hecla's operations has been limited to openings where long-term high quality support was required, in exceptionally difficult ground, and to a limited degree in stope support. Experience with both the wet and dry process indicated that the latter was better for their applications. The availability of effective accelerators which reduce losses from rebound, give high-early strength and permit placement in wet conditions, led to this conclusion. The gross cost under such conditions as those at Hecla, including rebound losses and overshooting, is estimated by Hecla to be $51 per cu yd.

Jan 12, 1969

By Richard L. Bullock

Drilling of small diameter blast holes in the conventional tunnel driving system or mining operation still consumes a significant part of the time and money required to extend an opening in rock. The use of pneumatic drills for most small hole applications has been the dominant tool used by miners and tunnel men alike throughout the world. But now, a, trend has been started that is showing major inroads into the traditional areas of pneumatics drilling for all types of rocks. Operators dealing in very soft materials, such as coal, salt or potash, traditionally had the option to use hydraulic power for their drilling tools. Twelve to fifteen years ago, drillers in medium hard, but nonabrasive rock extended their drill machine option by helping to develop a drill that still used air to power the hammers, but relied on hydraulic power for the rotational torque and feed thrust. (1) This was a significant step forward, particularly for those who drilled in rocks that were compatible to rotary-percussion bits. However, this application was in fact somewhat limited to the limestone and dolomite formation of mid-United States and the softer sediments in Europe. Now high performance rock drills have been developed, using all-hydraulics for both the hammer and rotation, that have many advantages over the conventional pneumatic systems. In two previous papers on this subject, (2)(3) this author reviewed in detail: 1) the characteristics of each of the manufacturer's products that were on the market; 2) The specific advantages of the all-hydraulic drilling systems; 3) Data from the applications of these drilling systems that was in use; 4) What was needed to further develop this drilling system and utilize its potential in the mining or tunnelling cycle. This paper will attempt to update previous papers, without reiterating many details of drill descriptions or

Jan 1, 1976