Search Documents

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By Andrew R. Klaetsch, Peter W. Deming

"The Washington Avenue tunnel in Kingston, NY was completed in 1912 to convey combined storm water and sanitary sewage. Over a mile in length, the tunnel was driven almost entirely in bedrock, with the exception of an approximately 170 foot long brick arch segment constructed in soil. About 90 years after the tunnel was put into service, persistent subsidence problems and sinkholes were observed in Washington Avenue above the shield-driven soil tunnel segment, eventually causing the important traffic thoroughfare to be closed. Subsequent tunnel inspections revealed a breach in the brick arch and a significant volume of fine soil within the tunnel. A two-phase remediation program was implemented to control seepage, reduce soil migration, and remedy sinkhole problems. The first phase included in-situ soil densification by vibratory pile probe driving to improve density in shallow sandy soil loosened by ground loss. The second phase included installation of a continuous soilcrete arch structure over and alongside the tunnel, extending to rock or compact glacial till and spanning the length of the soil tunnel segment. Overlapping vertical soilcrete columns were installed through interlayered sandy and clayey silt by jet grouting to form a continuous arch structure, using grout parameters verified by full scale field testing.PROJECT BACKGROUNDThe Washington Avenue tunnel in Kingston, NY (Figure 1) was completed in 1912 to convey combined storm water and sanitary sewage to Rondout Creek by the Board of Water Supply of the City of New York. The tunnel is over a mile in length and constructed primarily in rock. Contract documents indicate the tunnel was designed with a horseshoe shape at least 3 ft wide and 5.5 ft high."

Jan 1, 2016

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970's that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960's. In the early 1970's a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970's has therefore seen a very rapid pace

Jan 1, 1979

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

By Rafael C. Castro, Paul V. Savard, Kathleen M. Murtagh

Preliminary design is underway for the Massachusetts Water Resources Authority’s (MWRA) next major tunnel program, the Metropolitan Water Tunnel Program (MWTP). The MWTP is the latest part of MWRA’s ongoing efforts to achieve redundancy for its metropolitan water transmission system including its historic deep rock City Tunnel, City Tunnel Extension and Dorchester Tunnels. The MWTP comprises several deep rock tunnels that will be approximately 10-foot to 12-foot finished diameter totaling just over fourteen miles long and ten connections to existing large diameter surface piping and pumping stations. This paper will present an update on current engineering and permitting efforts, packaging schemes, and the schedule to complete the MWTP.

Jun 13, 2023

By Matthew Goff, Russell Lutch

The Great Lakes Water Authority (GLWA) operates the largest regional water authority in the State of Michigan. Two of the tunnels supplying raw water to the system from the Detroit River are the Springwells and Northeast Tunnels. The existing 70- to 90-year old concrete lined tunnels have experienced distress and cracking over their life requiring non-structural repairs to sections of the tunnels. For the repair, an interior stainless-steel segmental liner plate system has been designed to restore the watertight capacity of the tunnel liner and resist the exterior hydrostatic groundwater pressure in a dewatered condition. The team is utilizing a “wet repair” approach to perform the necessary repairs while the tunnel remains fully flooded and operational. To test and validate the tunnel repair approach, a full-scale mock-up of the proposed repair has been performed using underwater equipment and divers.

Dec 1, 2022

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By Stefan S. Kapusniak, Nichol Riggott, Stephen F. Smith

Stability investigations have been carried out in a number of major coal mining tunnels in the U.K. using various instrumentatcon techniques. The paper describes these instrumentation methods and presents results from studies in several tunnels. Both long and short term stability aspects are discussed. Prediction of tunnel stability is examined in relation to tunnel support requirements. Computer simulation techniques are used along with actual underground measurements to identify tunnel design parameters for influencing choice of support and prediction of long term stability.

Jan 1, 1984

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By A. G. Nitschke, I. Ossenbühl, W. Dolsak, J. Dase

"The authors have successfully developed an innovative rehabilitation concept, which meets actual technical standards and minimizes the impact on the operation of a key conveyor tunnel. A flexible and stepwise ground support rehabilitation program utilized a combination of yielding steel arch sections with grout filled fabric hoses, which represents a fast and safe backfilling support system. The system was developed and successfully installed at Bingham Canyon Mine, the world’s largest open pit copper mine, which also includes numerous underground structures. The mine is owned and operated by Kennecott Utah Copper (RTKC) a fully owned subsidiary of Rio Tinto. The system was implemented at a conveyance tunnel, which was originally designed as a railroad tunnel, but was re-commissioned and is currently used as a conveyor belt tunnel to transport ore from the open pit to processing facilities outside the mine. The existing structure showed signs of overstressing due to movements in the surrounding rock mass, which had to be addressed with a yielding support system in order to provide safe access into the tunnel. However, the impact on the conveyor belt operation due to support installation was to be limited to the bare minimum. Keywords: rehabilitation, yielding support, mining, stabilization, and grout filled fabric hose.PROJECT DESCRIPTION The C6 Tunnel is considered a critical asset for the operation of the Bingham Canyon mine as it comprises the standard route for transporting crushed ore from the open pit to the processing facility on a continuous conveyor belt system. The C6 tunnel was originally built as a railroad tunnel. Construction was completed in 1959. The original horse-shoe shaped cross section of the tunnel was 18 feet wide and 24-1/2 feet high [8]. The tunnel length was approximately 18,000 feet. During its service life, the railroad tunnel has undergone several transformations. The length of the tunnel towards the Bingham Canyon pit was shortened over the course of mining operations and the railroad tracks in the tunnel were removed. The invert was partially backfilled (3 feet typical) and a 72 inches belt conveyor was installed. Currently, the C6 Tunnel is nominally only approximately 21 feet high and 15,000 feet long. Ground Support and Rehabilitation Measures prior to 2014 The C6 tunnel was mined mainly with conventional mining methods, using drill & blast as the typical one. However, the weak geological sections, such as those encountered in the Fortuna fault, were excavated by shaping and chipping with machine-held moils [8]."

Jan 1, 2015

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001