Search Documents

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

Jan 1, 1879

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

"The Washoe Smelter is situated about two miles east of the City of Anaconda. The smelter site includes about 240 acres and peculiarly adapts itself in topography to the efficient handling of material. By reason of its being on a hill side it is possible to make the level of delivery of the product of one building the level of the charge floor of the next succeeding one.THE ORES: The ore treated comes principally from the Butte district and is hauled by the Butte, Anaconda & Pacific railway, a distance of twenty-eight miles, in trains of fifty 50-ton bottom-dump cars to the railroad yards at East Anaconda. At this point these trains are• split up according to their destination,—that is, as to whether they go to the concentrator and sampling mill ore bins, or to the storage bins. In each case they are made up into trains of eight or sixteen cars, according to the size of engine to be used, and are carefully weighed before delivery to their respective bills.Some idea of the magnitude of the works may be obtained from the following figures:Amount of ore that can be treated in 24 hours…12,000 tonsLime rock from adjacent quarries…2,300 tonsCoke used…500 tonsCoal for reverberatory use…500 tonsCoal for power use…50 tonsWater, per minute, 35,000 gallons.Men employed in and around Anaconda, 3,000. Monthly payroll for above, $300,000.00."

Jan 1, 1913

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By Randy Settgast, Daniel Moos, Hyunil Jo, Ghazal Izadi, Christine Baba

"Analyses of production logs of multiply fractured horizontal wells in unconventional plays show that only a small percent (~30%) of perforation clusters contribute to production. We present in this paper one possible approach to mitigating this problem, based on use of a fully 3-D numerical model of fracture propagation through a heterogeneous medium, by studying the influence both of spacing and of perforation friction on the initiation and propagation of simultaneous hydraulic fractures from a horizontal wellbore. The results indicate that while limited-entry perforating can help to equalize the lengths of fractures simultaneously growing from multiple clusters, it cannot equalize their widths. Both fracture width and fracture length can be equilibrated by combining non-even cluster spacing with limited-entry perforating. This has obvious benefits as it allows equalized placement of proppant across the entire series of perforation clusters, resulting in similar fracture widths and conductivities which enhances the likelihood that all clusters will contribute equally to production.INTRODUCTIONThere is substantial evidence from production logs and other information that during the hydraulic stimulation of horizontal wells, not all perforation clusters within a given stage will produce. One possible cause is the interaction between the hydraulic fractures emanating from each perforation cluster. Typically fractures created at the outer perforation clusters create “stress shadows”, i.e. increases in compressive stress in the minimum principal stress direction, which limit the growth of fractures growing from interior clusters; this is confirmed by modelling [1, 2, 3]. An example of this can be seen in Figure 1 which shows the final configuration of simultaneously propagating fractures from multiple, evenly spaced clusters when there is no perforation friction. The inner fractures are substantially shorter, reproducing the results by Bunger and Peirce [3]. The inner fractures also have substantially smaller widths.One approach to equalize the growth of simultaneously propagating fractures from a horizontal wellbore is by using limited-entry perforating as a method to equilibrate the flow rates into each of the different perforation clusters. Perforation friction is caused by the finite diameter of the entry points into the formation, and leads to a pressure drop across each perforation which is proportional to the flow rate squared. Fractures that take more fluid have a higher fluid velocity through the perforations than fractures receiving less fluid. This causes a larger pressure drop between the wellbore and more rapidly growing fractures, compared to the same pressure drop between the wellbore and the fractures that grow more slowly. Because pressure within the wellbore is approximately the same at each entry point, the larger pressure drop leads to less pressure being delivered to rapidly growing fractures, thereby decreasing their ability to propagate and reducing the amount of fluid they are able to receive. Because the mass rate of injection into the wellbore is constant, this forces more fluid into the fractures that were propagating more slowly, increasing their growth rate. It also increases the pressure required to drive fluid injection. The balance of these effects makes the system largely self-regulating and delivers more balanced fracture growth. While this effect is well known, it is often neglected in current numerical models."

Jan 1, 2015

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By J. Kang

Large-scale land reclamation has been undertaken in Singapore since the 1960s. In the early years, the fill materials excavated from the hills. In recent years, sea sand is the main source of the fill materials. The contractors used to import the sea sand from the neighbouring countries such as Indonesia. However, in early 2000, the sea sand import from Indonesia and Malaysia was banned. Cambodia, Myanmar, and Philippine therefore became the alternative sources for sea sand. Distance between the jobsite and these countries is over 1,200 km, and transporting sea sand from these areas became a critical issue that could affect the contractor?s performance. Figuring out the right combination of transportation means for a longdistance sand transportation would be challenging because of uncertain situations. We developed a stochastic simulation model, using ARENA, to figure out the right quantity of small-size barges, bulk carriers, and loading/unloading equipment, which could help project managers yield the most production for sand transportation. This paper presents how we developed the simulation model, how it was applied to figure out the optimum combination among various size barges, different bulk carriers, and various types of loading/unloading equipment, for the sand transportation project in Singapore.

Aug 1, 2013

By Paul F. Thiele

The mining industry of Georgia, while not as large as in some other states, is still an important part of the economy. Total value of mineral production in 1966 was $148.6 million.l/ Clays and stone produced the most income, Other minerals included sand and gravel, iron ore, mica, talc, barite, bauxite, cement, feldspar, kyanite, peat, and rare-earth metals, titanium and zircon concentrates. Georgia ranks first among the states in production of kaolin, second in fuller's earth and rare-earth concentrates, third in bauxite and kyanite, fourth in barite and ilmenite, and fifth in feldspar. It is quite likely that phosphates will one day be mined in the south eastern part: of the state, and that alumina will be produced from the extensive kaolin deposits in the central part of the state.

Jan 1, 1968

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By Allen Latham

It started' in 1936 when some Dutch adventurers wanted to scale the highest mountain in the South Pacific. Quite by accident, they discovered the Ertsberg, a contact deposit of magnetite laced with chalcopyrite, in a high mountain valley where it had been gouged at by glaciers and finally left as a solitary pillar for its discovery by a geologist who lent purpose to the expedition, Dr. J.J. Dozy. By the-.time a report was published describing the deposit, war had hit the Netherlands. Perhaps again by accident, the report was uncovered in 1959 by the East Borneo Company. At this point, Freeport entered the scene through its vice president for exploration, Forbes Wilson. During the course of a meeting on laterite prospects, the Ertsberg was introduced and he put the wheels into motion for Freeport to join in its exploration. You might, at this point, ask yourself whether you or your company would have taken on a venture to look at a reportedly large high grade copper outcrop in New Guinea, an unexplored land known best for its inhospitable climate, terrain and head-hunters. I heard the chief executive of one large mining company comment sometime back that neither he nor his company would have gotten involved. I won't attempt to describe the trials of the initial exploration expedition that passed through dense-man grove swamps, tropical jungle and across jagged mountains a distance of some 200 miles to get to the Ertsberg in 1960. It should be chronicled by its participants - Forbes Wilson, Del Flint, and John Bowenkamp. Needless to say, the participants relish the experience but wouldn't be among those volunteering for a return engagement. As a result, the Ertsberg changed from a reported outcrop to a mineral deposit containing an estimated 13 million tons with systematic surface sampling indicating a copper grade of over four percent. Moreover, the deposit extended to an indeterminate depth with the possibility of doubling or tripling. reserves well within reason.

Jan 1, 1971

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By Oliver Bowles

TO keep pace with technical progress is an important function of any industry. All branches of mining may learn important lessons by observing progress made in other branches. The non-metallic mineral industries may learn much from each other as well as from the metal miner and the metallurgist. Recent technical advances which have come to the attention of the Committee on Non-metallic Minerals are presented herewith for consideration and comment. It is planned to present this review for open discussion at the February, 1931, meeting of the Institute. Comments will be welcomed either in the form of written or oral discussion. It is desired that new developments not covered in this paper be brought up at that time. Some notable advances have been made in cement technology. Recognition is now being given to the advantages of closed-circuit grinding of cement raw materials in wet-process plants, with stage removal of the fine materials, It increases mill capacity, reduces the wear of grinding media, and also reduces the power requirement. The method is well known in metallurgical plants, and its acceptance by cement companies is another illustration of the lessons the non-metallic industries may learn from the metal industries. Closed-circuit dry grinding has also proved advantageous for both raw materials and clinker.

Jan 1, 1931

By Noel S. Christensen

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The commercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depend¬ing upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Emery R. Hayhurst

SILICOSIS has been described in a report of the American Public Health Association as a disease due to breathing air containing silica, characterized anatomically by generalized fibrotic changes and the development of miliary nodulations in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for work, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray findings. ... The disease is divided arbitrarily into first, second, and third stages for convenience of description and possible compensation purposes. At least two distinct types of silicosis are recognized, acute and chronic. The acute form was reported as early as 1713, when a British patent for grinding flint by wet methods was granted because the dry powdered material "proved very destructive to mankind, so much that any person, ever so healthful, working in that business cannot possibly survive over two years."

Jan 1, 1936

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By H. H. Stoek

(Wilkes-Barre Meeting, June, 1911.) THE origin of the Mine-Rescue Service of the State of Illinois can be traced to two distinct sources, the work of the Rescue Station at Urbana and the Cherry disaster. During the early part of the year 1909, the Technologic Branch of the U. S. Geological Survey, now the Bureau of Mines, in connection with the Illinois Geological Survey and the College of Engineering of the University of Illinois, established at the University of Illinois, in Urbana, a branch rescue-station to supplement the work of the Pittsburg station of the Geological Survey. As a result of the work of training at the station in Urbana by R. Y. Williams, mining engineer, and James Webb, foreman of the Bureau of Mines, and the use of the helmets at several mine-accidents in the State of Illinois, . the people of the State were somewhat familiar with oxygen-helmets when the Cherry disaster occurred, in November, 1910. The oxygen-helmets were successfully used in connection with that disaster, and upon the recommendation of the Illinois Mining Investigation Commission, the Legislature of the State, assembled in special session during the winter of 1910, passed a bill appropriating $75,000 for the erection and maintenance of three rescue-stations, stipulating that they should be located in the northern, central, and southern parts of the State. The Act also provided that the stations should be in charge of a Commission of seven, two representing the United Mine Workers of Illinois, two the mine-operators, one the Federal Bureau of Mines, one the State mine-inspectors, and one the Department of Mining Engineering of the University of Illinois. This Commission was called together by the Governor of the State, Aug. 2, 1910, and since that time three stations have been located, built, and equipped: at La Salle for the northern

Dec 1, 1911