Search Documents

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change in coal seam inclination, Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in, diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, productlon to 500,000 ton/yr can be achieved. Volume I provides an overview of machine, systems and productivity.

Jan 1, 1977

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By Bobby B. Gillenwater

This report presents recommended guidelines and regulatory changes applicable to electrical installations in underground oil shale mines. These recommendations are based on information gathered from oil shale operators, government agencies, and other knowledgeable sources familiar with existing plans for mining systems and electrical installations, and on present understanding of the problems and hazards associated with oil shale mining. Additional discussions of specific electrical problems related to oil shale mining are also presented. These specific problems include: ? Ground fault current levels ? Permissible electric wheel motors ? Permissible batteries and electric starting systems ? Intrinsically safe instrumentation and applicability of existing test standards.

Jan 1, 1983

By R. W. Raymond

On the Manchuria. SOMEWHAT fatigued with excess of enjoyment and strenuous continuity of movement on the trip to and through California, the members and guests of the Institute party embarked Tuesday, Oct. 17, on the Pacific Mail S. S. Manchuria for a further journey to and through Japan. The good ship displayed the flag of the Institute (blue cross-hammers on a white ground), together with the Stars and Stripes and the ensign of the company. Uninterrupted fair weather and smooth water attended the passage to Honolulu. The Manchuria proved herself most commodious, comfortable and clean ("A sweeter steamship never sailed," quoth President Hunt) ; Captain Dixon and his officers were most agreeable, as well as most efficient; the passenger list comprised many congenial people besides ourselves-among them a score of missionary folk, and also Mr. M. H. de Young, Vice-President of the Panama

Jan 1, 1912

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By Richard E. Thill

The Bureau of Mines' Oil Shale Data- Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra Brake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDB listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

The 53 countries that constituted Africa in 1992 accounted for a significant portion of total world output of a number of mineral commodities. However, the continent's total output for a number of major mineral commodities declined relative to the volume produced during 1991. (See tables 1 and 2.) The most conspicuous declines in mineral production from 1991 to 1992 were for cobalt and copper (declines of 28.6 % and 23.4 %, respectively), which could be partially attributed to mining and metal processing difficulties caused by political and economic disruptions in Zaire and for uranium (12 % drop), for which much of the continental production decline was ascribed to Namibian cutbacks in response to lower world prices. The severe regional drought also adversely affected the mineral industry in a number of sub-Saharan nations.

Jan 1, 1994

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By H. M. Coggin

The study summarizes the state of the art in rock mechanics, open pit and underground mining, leaching, geology, metallurgy and financial analysis Conceptual design of pit slope caving technique and analyses explore concepts for the exploitation of ore grade remnants in the walls and bottoms of open pit mines and the potential economics of the adaptations Several coded sites were examined for future studies where the feasibility of the method may be demonstrated. An extensive bibliography has been developed

Jan 1, 1977

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

By M. Veiga, L. Lavkulich, R. Pakalnis, M. Ghomshei, S. Baldwin, J. A. Meech

"On July 26, 2000, the Canada Foundation for Innovation announced an award of $1.3 M dollars for The Centre for Environmental Research in Minerals, Metals and Materials, CERM3, at The University of British Columbia. Additional funding was also provided by the British Columbia Knowledge Development Fund ($1.3 M) and the UBC Stewart Blusson Fund ($0.7 M). Annual industrial grants and contracts are providing support funding for the on-going research projects. Corporate membership in CERM3 entitles each participant to a seat on the technical advisory committee (TAC) as well as access to the five laboratory facilities currently under construction. Both the federal and provincial governments will also participate in the TAC through NRCan-CANMET and the BC Ministry of Energy and Mines, respectively. CERM3’s mission is:• to develop innovative methods to deal with environmental problems created by mining activity;• to promote sustainable development as a hallmark of management decision-making; • to produce mining and processing engineers with the required environmental skills; and• to enhance the image of mining in society as a vibrant and necessary component of a modern economy and society which disturbs the environment for the benefit of mankind.CERM3 brings together a multi-disciplinary team of researchers from over 12 departments at The University of British Columbia (UBC) to work on mining-related environmental problems. These include: chemistry; soil sciences; chemical and biological engineering; earth and ocean sciences; microbiology; civil engineering; electrical engineering; metals and materials engineering; mechanical engineering; mining and mineral processing, the Westwater Research Centre; the Institute for Resources and the Environment; and the School of Occupational and Environmental Hygiene. The centre intends to interact with scientists from industry, governments and other universities across Canada and around the world. CERM3 aims to become Canada’s leading environmental research facility for the mining industry. This paper describes the evolution of CERM3 and its coordinated multi-disciplinary approach to mining and the environment. Some of CERM3’s research projects include:• developing new protocols for environmental analyses to provide consistent and reliable assays;• isolating a natural virus for Thiobacillus ferrooxidans and other bacteria responsible for acid rock drainage (ARD);• designing bio-remediation and adsorption techniques for mine effluents;• promoting and enhancing the use of hydrometallurgy to reduce environmental pollution;• examining new approaches to comminution to decrease energy consumption;• developing a magnetically levitated hoisting system to reduce the footprint of a mine operation;• building a state-of-the-art supercomputer network laboratory for mine/mill simulations; and• designing intelligent bulkheads to seal tunnels following mine closure to survive for 1000 years.This latter project involves the establishment of a research station at the Britannia mine site, 45 km north of Vancouver, which will provide a full-scale facility to design the “Millennium Plug” and contribute directly to the solution to one of North America’s worst ARD-contaminated sites."

Jan 1, 2003

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946