Search Documents

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By Z. Eisenstein, H. Heinz

INTRODUCTION Contemporary underground transit systems often require cross sections which are not adaptable to shield tunnelling. Due to the frequently large dimensions of these cross sections, which are normally situated at shallow depths and in soft ground, full face advance is not feasible because of ground control and construction requirements. Ground deformation and face stability are controlled by "staged excavation", which consists of sequentially driving smaller, specially arranged, individual headings hence avoiding full-face excavation. Shotcrete is normally used for initial support and these tunnels are frequently described as applications of the New Austrian Tunnelling Method (NATM). Figure 1 illustrates the relative size of large cross section tunnels with respect to conventional shield tunnels. Within the scope of this paper, 'large' cross sections are defined as those whose continuous (i.e., without intermediate pillar support) cross sectional excavated area exceeds 60m2. This definition includes most double track highway, railway and subway tunnels, subway stations and some single track railway tunnels. Excavation schemes which have been more frequently used for continuous cross sections (i.e., with no intermediate pillars) are presented in Figure 2. This classification is an extension of that presented previously by Eisenstein et al. (1986). The symbols used for classifying the excavation schemes are formed by the letter T (for "type"), followed by a number, which represents the number of excavation stages fully embraced by a shotcrete ring, termed "cells" by Lessmann (1986). The numbers inside the cross sections in

Jan 1, 1989

By Pierre Hines

THE. Owyhee Tunnels in eastern Oregon were started in the early part of 1930, and were completed early in 1932, with the excep-tion of the Magoffin contract. One tunnel is a large water tun-nel, and the other is a small water tunnel; each is approximately tour miles long. Modern equipment was used to full advantage, and remarkably fast time was made during the driving period. The ,J. F. Shea Co., con-tractors, of Portland, Oregon, have broken established records in the smaller tunnel. Their methods are described in detail. The time of a complete round has been reduced by intelligent handling of mechanical shoveling, and this article records some of the useful facts developed. Charles A. Shea (president of the J. F. Shea Co., and secretary of The Six Companies, Inc.) not only granted permission to publish this article, but placed the company's complete daily reports at the writer's disposal. These reports were made out to conform with previous records upon important tunnel work, and enable a comparison to be made of actual averages, rather than ideal cycles, or representative cycles. Gilbert Shea, present superintendent, has been helpful with time, criticisms, and corrections of the information presented. Morton S. Boss, superintendent during the first 15 months of the tunnel work, gave many hours of his time during two visits lasting over two weeks. The whole staff of the J. F. Shea Co. has given encouragement and assistance.

Jan 1, 1933

By Musa MA

Tunnel excavation for sewer construction long remained a labour intensive, hazardous and costly operation. Even with the of mechanical and semi-mechanical shields for tunnel excavation, many problems remained until recently. In the past decade, however, the technology has changed dramatically which has made possible the use of advanced tunnelling methods for sewer construction.

Jan 1, 1993

By B Shen

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for approximately 14 km linking the Mt Thorley rail loop and the Wambo Coal Mine. The project involves a 260 m long tunnel in weathered sedimentary and intrusive materials. The tunnel has a low cover and runs under a main highway. This second paper on the project looks into one aspect of the tunnel in detail: the use of shotcrete arch as the primary support for part of the tunnel excavation. The use of shotcrete instead of steel arch, formulation of the material specification, construction sequencing, installation at the excavated face and material testing for verification related to this facet of the project will be discussed in this paper. The tunnel opened in April 2006, and two years on, we briefly reflect on the impact of this design decision on the overall project.

Jan 1, 2008

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999

By L. A. Wright, J. F. Emerson

The Pine Creek mine, owned by Union Carbide Nuclear Co., Div. of Union Carbide and Carbon Corp., is one of the world's largest producers of tungsten. The mine is located on the eastern slope of the Sierra Nevada Mountains, about 25 miles north- west of Bishop, Calif. Prior to 1948, production from the property came either from surface pits or from underground workings above A level haulage tunnel. The tunnel is at an elevation of 10,900 ft, which left 500 to 600 ft of vertical backs to the surface outcrops. Heavy production demands during World War II hastened the planning for long range development of orebodies below A level. A 7000-ft haulage tunnel, 1500 ft below A level, was started in 1943 and completed in early 1947. This haulage tunnel is at an elevation of 9400 ft and is known as Zero tunnel.

Apr 1, 1956

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

Currently an Australian Standard for tunnel fire safety is being developed for road and rail tunnels. Other local guidance relating to tunnel fire safety that has recently become available includes publications by both the Roads and Traffic Authority and RailCorp of New South Wales. Internationally, the World Road Congress has completed its 2004 - 2007 cycle, which has resulted in a number of publications. International developments in rail guidance include a new European Standard regarding fire safety in railway tunnels that will come into effect in July 2008. In addition, the National Fire Protection Association committee NFPA 130 are in the process of revising their standard for fixed guideway transit and passenger rail systems, which is due for publication in late 2009. This paper outlines the status of these and other recently published relevant local and international fire safety guidelines and their implications for tunnel projects in Australia.

Jan 1, 2008

Every two years, industry leaders and practitioners of tunneling and underground construction gather at the Rapid Excavation and Tunneling Conference (RETC) to learn from their peers about the most recent advances and breakthroughs in this unique fleld. Industry experts from around the world highlight their most recent projects and share real-world experiences. They also share with their colleagues new technologies and methodologies that attendees can take home to their respective projects. The 2013 RETC was held June 23-26 in Washing-ton, D.C., itself home to several major tunneling and underground construction projects. The conference is sponsored by SME. Attendance was 1,384 professionals. The accompanying exhibit hosted 159 companies in 188 booths. A few of the topics covered in the technical sessions dealt with caverns and large spans, contracting practices, tunnel linings, design and planning, geotechnical considerations and instrumentation. The conference was preceded by four short courses, all well attended. They were ?Grouting in Underground Construction,? ?Tunnel Lining Design,? ?Microtunneling Application? and ?Risk, Uncertainty and Hard Decisions.? In addition, a sold-out field trip to D.C. Water?s Blue Plains Tunnel took place following the conference. The Blue Plains Tunnel is part of the agency?s Clean Rivers Project. Also during the meeting, three students each received $5,000 scholarships from the UCA of SME, while another three students each received $2,500 scholarships from RETC (See page 53).

Sep 1, 2013

By Harvey Parker

This is part two of an article on the prominent role that the United States and its industry leaders have played on the International Tunnelling and Underground Space Association (ITA), which represents the underground construction and underground space industries worldwide. The U.S. is officially represented in ITA by UCA of SME. (Part one is in T&UC, June 2007, pp 39-42) Tunnel advances in 1960s and 1970s The 1960s and 1970s were active and productive times for the U.S. tunneling industry. During that time, federal programs, sponsored by the Federal Railroad Administration (FRA), the Office of High Speed Ground Transportation (OHSGT) and the Advanced Research Projects Administration (ARPA), stimulated tunnel research and development. Also, the American Society of Civil Engineers (ASCE) and SME collaborated to create the Underground Construction Research Council (UCRC) and the Rapid Excavation and Tunneling Conference (RETC) series.

Jan 1, 2007

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

By D Maconochie, S Pradhan, M Reed

The Waterview Connection will provide a high-quality strategic alternative to State Highway One and complete Auckland’s Western Ring Route connecting State Highways 20 and 16. The project includes twin three-lane motorway tunnels 2.4 km long and 13.1 m internal diameter (ID). The tunnel construction started in November 2013 using the tenth largest earth pressure balance (EPB) tunnel boring machine (TBM) in the world. The tunnels will pass beneath urban and greenfield areas as well as a major local arterial road. The project is being delivered by an alliance of constructors, designers and the New Zealand Transport Agency. This paper describes some of the key innovative and cost saving design solutions that have been achieved through collaboration in the alliance environment with the construction team, owner’s verifier, the segmental lining precast suballiance and the M&E suballiance for the underground works. The key design elements of the tunnel comprise a three-lane roadway, invert culvert and backfill, precast segmental lining, sixteen mined cross passages including a low point sump cross passage and steel segments for opening to the cross passages. This paper reviews interdisciplinary design integration and the economies achieved in the permanent works tunnel lining design, including reduction in lining thickness and optimising reinforcement, cross passage separation of 150 m, efficient design of the invert culvert and backfill design, main drainage pipe and low point sump. The paper also describes the attributes of the TBM and the invert culvert construction methodology.CITATION:Pradhan, S, Maconochie, D and Reed, M, 2014. Tunnel design in an alliance for Waterview Connection, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 425–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

"Boston’s Central Artery passes beneath nine active railroad tracks carrying commuter and Amtrak trains into South Station, the City's busiest rail terminal. These railroad operations had to remain in service throughout the construction of the “Big Dig”. The solution was to jack the tunnel under the tracks, rather than build the tunnel by more conventional means.Jacking of utility pipes is fairly common, but jacking boxes as big as a highway had never been done in North America, until the Big Dig came along.Soil freezing was decided upon as a means of stabilizing the soil under the tracks. This allows the tunnels to be jacked into place without soil caving when the soil is excavated at the leading face of the advancing tunnel boxes. Hundreds of pipes were driven into the ground between the tracks. Inside the steel pipes were smaller plastic pipes. A freezing plant near the railroad tracks pumped refrigerated brine into the inner plastic pipes. The brine ran out the bottom of the inner pipe, flowed up to the top inside the outer pipe, and was re-circulated to the freezing plant and back again into the ground. Over several weeks the circulating brine drew the heat out of the soil little by little, and froze the ground outward from the pipes. Soil FreezingThe plan required the construction of jacking pits in which the tunnel boxes could be constructed, and from which they could be jacked forward to their final locations, as described in the accompanying article. Once the jacking pit was built and the tunnel box constructed inside the pit, crews made an opening in the headwall of the pit to allow passage of the tunnel sections, excavated about three feet of the frozen soil, pushed the tunnel box ahead, and repeated the procedure again and again."

Jan 1, 2003

By Vince Luongo

"INTRODUCTIONThe West Side Combined Sewer Overflow (CSO) Tunnel Project is located in Portland, Oregon and is part of the Willamette River CSO Control Project. The purpose of the West Side CSO Project is to reduce the frequency and volume of combined sewage overflows from the drainage areas on the west side of the Willamette River using the West Side CSO tunnel as a combined storage and conveyance facility. The sewage is then directed to the Pump Station on Swan Island, which is located on the east side of the Willamette River. From here the combined sewage is pumped through force mains that discharge into the existing Peninsular and Portsmouth tunnels.The West Side CSO tunnel has an inside diameter of 14-feet (4.27m) and is approximately 18,150-feet (5,532m) long. The tunnel slopes at a constant down gradient of 0.0018 from south to north over the entire length of its alignment.The tunnel passes beneath six existing bridges; Hawthorne Bridge, Morrison Bridge, Burnside Bridge, Steel Bridge, Broadway Bridge and Fremont Bridge. The general tunnel alignment follows beneath the Naito Parkway starting at Clay Street Shaft and connecting three other shafts on the west side of the Willamette River, Ankeny Shaft, Upshur Shaft and Nicolai Shaft. It then passes below the Willamette River and on to Swan Island to connect with the Confluent Shaft, which will combine flows from the West Side CSO and East Side CSO (not part of this contract) and then continues to the Pump Station Shaft.The Nicolai Shaft is the primary mining shaft from which two TBM’s were launched to construct the West Side CSO tunnel. The first TBM started mining south and terminated at the Clay Street Shaft. The second TBM started mining north below the Willamette River and terminated at the Swan Island Pump Station Shaft."

Jan 1, 2006

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

During the last 20 years, more than 80 km (50 miles) of tunnels have been constructed in the Los Angeles, CA area. Recent projects include The East Central Interceptor Sewer (ECIS), completed in 2004. It spans more than 18 km (11 miles). The Northeast Interceptor Sewer (NEIS), completed in 2005, spans 11 km (7 miles). And the 2-km (1.3-mile) Metropolitan Transportation Authority?s Gold Line Eastside Extension (MCGLEE) was completed in 2006. All of the tunnel routes lay beneath heavily populated urban environments so minimizing ground surface settlement was critical to the success of the projects. Previous tunneling efforts in the Los Angeles area using open shield methods resulted in significant settlement that damaged roads, utilities, buildings and other structures. Earth pressure balance (EPB), or slurry machines, were specified for these projects to reduce subsidence risk. The contractors chose EPB tunnel boring machines (TBM) for the work. The closed and pressured face of the EPB TBM reduces loss of ground at the tunnel face and, when the machines are used in combination with gasketed pre-cast tunnel liners and backfill grout behind the installed segments, losses from over-cut of the excavated surface are also reduced.

Jan 1, 2008

By Jack C. Stuart, Robert L. Obradovic, Allen J. Hulshizer, Anthony J. Stewart

Two deep bedrock tunnels, extending over a mile into the Atlantic Ocean, to provide the cooling water requirements for the Seabrook Station represent a major tunneling venture. This paper provides an outline and discussion of the planning and construction work associated with developing of the land riser and work shafts and the conventionally excavated tunnel station area.

Jan 1, 1979

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001