Search Documents

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By Stanisław Prusek, CHONG WEI, Huawei Xu, Jun Wang, Andrzej Walentek, Artur Dyczko, Derek B. Apel

The excavation-induced stresses transferred from the panels or pillars in upper coal seams play a key role in the occurrence of rockbursts in driving roadways during close-distance coal seam mining, which has become a common problem and threat to many underground mines. The authors established a 3D finite-difference numerical model via FLAC3D software using the closedistance coal seam mining conditions in the Zofiówka Mine as a case example to reveal the rockburst mechanism in such conditions. The excavation-induced vertical stresses are analyzed, which provides a basis to build a conceptual model to explain the possible source mechanism of the rockburst under such conditions. Nine typical rockburst indicators considering different contributing factors are then selected as the evaluation criteria to assess rockburst potential in the study site. The results suggest that the superposition of multiple excavation-induced stresses of the main drift and tailgate provides an environment for stress concentration and energy accumulation. The side abutment stress induced by mining in the upper coal seam has a “strengthening” effect to the rockburst occurrence. The great deviatoric stress induced by complex excavating situations is another important exterior cause. A strict calibration procedure should be implemented before using indicators to predict rockburst potential. A methodology was proposed to estimate the location and magnitude of rockbursts combined with numerical modeling, laboratory tests, and feedbacks from the field. The study could provide some references and guidelines for preventing and mitigating rockbursts in underground mines under similar engineering conditions.

Aug 26, 2021

By Verya Nasri

The use of a single tunnel boring machine (TBM) tunnel of approximately 12 to 13 m (40 ft to 43 ft) diameter for transit systems to house both light rail or subway tracks in a stacked configuration is an advanced concept that allows significant savings in construction cost and time while reducing, to a large extent, the negative effects on the environment. This solution, similar to the recently completed Barcelona Metro Line 9, integrates station platforms, train storages, crossovers, bypass tracks, ancillary areas and utility corridors inside a single tunnel. Each of the underground stations consist of a cut-and-cover entrance structure and ventilation shafts, that also serve as emergency exits. The excavations for the station structures and shafts can be done on one side of the street with nominal impact on traffic and utilities.

Jan 1, 2010

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By G. F. Kuncir

This volume was prepared in support of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation under a Bureau of Mines contract. The evaluation is described in part within a companion volume entitled Benefit-Cost Analysis. The economic mine models outlined herein provide a quantitative basis for the assessment of program benefits. Reference is made to estimated oil shale mine costs to delineate the beneficial impacts that can be expected to accrue for the future implementation of program developed technology. Estimated mine cost data are provided for surface, underground, and modified in situ oil shale mining operations.

Jan 1, 1977

By Erica Frederickson

"Millennials. Doesn’t the word just make your blood boil? You’ve probably encountered one of those kids who think they know best despite a lack of any real experience.Hi, my name is Erica, and I am a Millennial. We often get a bad rap, sometimes for good reason. But we do have qualities that are often overlooked. For example, I am happy to share with my generation a real desire to make a difference in the world and a commitment to innovation. Does this mean I think we always have good ideas? No – especially not right away. After all, few of us came anywhere near a piece of construction equipment until arriving for our first job, as was the case for me. We may have fancy degrees, but not many of us learned to run a jackleg drill in school.Two weeks after graduating college in 2011, I packed up my bags and moved to New York City to work as a field engineer for Traylor Bros. Inc. on the Queens Bored Tunnels project (Granite/Traylor /Frontier Kemper, JV), part of NYC MTA’s multi-billion dollar Long Island Railroad East Side Access project. It was here I became acquainted with the notorious New York City union workers. Perhaps the greatest challenge of my career thus far was earning the respect of the field supervision and craft workers on this first project.The first time I asked a maintenance mechanic to clean a piece of equipment in accordance with our maintenance protocol I got a flat-out “No.” It was the most powerless I had ever felt. But why should these experienced workers trust a 21-year-old girl with her civil engineering degree and no prior experience? I realized no employee on the job had any reason to listen to me — not until I proved my worth. Fortunately, I arrived on the job site just as we were commissioning the slurry plant for the first tunnel drive. I dove into learning as much about the slurry tunneling process as possible and was able to quickly pick up the ins and outs of running the slurry separation plant. As none of the other engineers or management had first-hand experience on a slurry tunneling job, I soon became the go-to engineer in the slurry plant. No one questioned me if I asked to have something done around the plant after that, or if they did, they quickly learned that I had a convincing answer as to the need for the task. I was even able to play a large role in shaping our slurry monitoring and control methodology."

Jan 1, 2015

By R. V. Norris

1. INTRODUCTION. THE anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, in the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which,, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jun 1, 1911

By John C. Holtz

"The Federal Bureau of Mines serves the mining industry by approving equipment that is designed to prevent explosion, fire, shock, or toxic hazards in mines when such equipment is used and maintained in a proper manner, through research, consultation, testing, and inspection, the Bureau studies machinery and component parts submitted by manufacturers and others. Before receiving the Bureau's approval as permissible for safe use in mines, equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's various permissibility schedules. An important phase of the Bureau's research is the testing of diesel engines.Mobile diesel-powered equipment can be used safely in underground noncoal mines and tunnels when mechanical ventilation is provided to dilute and remove the exhaust gas and to replenish oxygen in the underground atmosphere. Safe ventilation is determined by suitable tests of each engine used in a diesel machine. This ventilation cannot be predicted safely, accurately, and economically from any general empirical relationship.In determining safe ventilation, the quantities of carbon dioxide, carbon monoxide, and oxides of nitrogen generated by a diesel engine must be ascertained. These quantities are related to the displacement of the engine, its speed of operation, the design of the combustion chamber, and the fuel:air ratio needed to produce useful power. At overrich fuel:air ratios, all diesel engines generate excessive quantities of toxic carbon monoxide and smoke. The results of engine tests are used to determine a maximum fuel-injection rate at or below which carbon monoxide can be controlled by a reasonable ventilation and smoke is essentially eliminated. Toxic oxides of nitrogen are related to fuel:air ratio and the design of the combustion chamber. Their concentration in the exhaust cannot be controlled by engine adjustments, and each engine appears to have individual characteristics concerning formation of these oxides. Production of oxides of nitrogen frequently is the most important factor in determining safe ventilation."

Oct 1, 1959

By M. S. Diederichs, G. Walton

"Developments in understanding the brittle fracture of rock over the past two decades ultimately led to the acceptance of a cohesion-weakening-friction-strengthening model as an appropriate strategy for the modelling of spalling using a continuum approach. This strength model has been used to replicate observed failure depths and geometries for a number of case studies in the literature, most notably the AECL Underground Research Laboratory in Manitoba. One thing which these case studies typically ignore, however, is the influence of rock dilatancy on the evolution of brittle failure. Physically, this phenomenon is the volumetric expansion of the rock due to fracture opening; numerically, this phenomenon is captured by the flow rule, which is often characterized by the dilation angle, ?. Accurately modelling rock dilatancy in conjunction with strength evolution is necessary both to predict the magnitude and distribution of ground displacements, as well as the exact depth and shape of the fracturing zone. Both of these factors can have significant implications for support design. This paper is focussed on presenting some of the recent developments in this field in the context of a number of numerical modelling case studies. Initially, a new model for the dilatancy of brittle rock is presented, as well as some representative data and model parameters for different rock types. Next, several case studies of highly stressed tunnels and shafts are presented. The results of continuum numerical models are presented to demonstrate the ability of the back analyses to match observed in-situ measurements and obtained. The predictive capabilities of the material model are also highlighted for cases where sufficient “a priori” information (such as laboratory compression testing data) are available. The issues of model nonuniqueness and strain-localization/bifurcation are also addressed."

Jan 1, 2015

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By Charles M. Keenan

THIS PUELICATION lists and provides brief accounts of the major disasters not classified as explosions of gas or dust that have occurred in the cod mines of the United States from the earliest times to the present. Together with an earlier publication of the Bureau2 it provides information on all the known major coal-he disasters (disasters causing five or more deaths) in this Nation's history. Sources of each account are given individually. In each account the actual words of the original publication are used unchanged, but sentences or paragraphs referring to details that are not significant have been omitted. In those few cases where conflicting data were reported in different publications the selected version is the one that appears most logical and which in general is in agreement with most of the other accounts.

Jan 1, 1963

By W. Ter-Minassian

Besides the question of the stability of the roof and walls, one of the main problems encountered with tunnelling and shaft-sinking through the soft ground of alluvial origin forming the sub-grade of most large towns is settlement. Public transport and road tunnels in town centres are particularly affected, as they cannot generally be designed at any great depth for several reasons, such as the fact that ventilation shafts and access to the surface by means of stairs, escalators, lifts, ramps and so on must be fitted into the limited space available and are therefore costly, and because of the difficulties of driving below the water table. It is for this reason, coupled with the need for wide radius curves, that tunnels now so often pass close under buildings and monuments which must not be exposed to any risk of damage from subsidence during excavation. Grouting is the usual method used for consolidating soils, improving their strength and making them less compressible, but it is itself liable to cause heaving and cracks in the buildings above and has many other attendant dangers, including continually revised estimates which are the reason for the often inordinately high costs met with in urban tunnelling to-day. The mechanics of the problem have been studied and it has been found that a fraction of the total settlement is

Jan 1, 1997

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By H. Dr. Boldt, J. Dr. Henneke

PREFACE In German coal mines the application of tunnel boring machines has become a very effective and economic technique for major development works. After initial trials around 1970 the breakthrough was reached by driving 13 km of road ways on Rheinland and Friedrich Heinrich collieries, using a DEMAG tunnel boring machine of 6 m diameter. INTRODUCTION The coal mines of Rheinland and Friedrich Heinrich are to be found in the West of the Ruhr Area, the largest coal mining area in the Federal Republic of Germany (Table 1). They form part of the Ruhrkohle company. Rheinland coal mines produces 41000 to 43000 t of run-of-mine coal every day, of which 20500 t are usable coal. Friedrich Heinrich has a daily production of 17000 t of run-of-mine coal, 9000 t of which are usable. The coal is worked at depths of 600 to 1100 m in seams 0.6 to 3.0 m thick. The method of mining is longwall, and the machines used are ploughs and shearer loaders. From 1973 to 1980 a programme was put into operation in these two mines to develop and open up the coal field on the 885 m level. A total tunnel length of 20 km was to be driven. After thorough investigations it was decided to employ a full-face tunnel boring machine for

Jan 1, 1981

By Tagawa H

In Japan, geological condition do not only vary in a wide range of strata but are also extremely complex with the existence of faults and aquifers. With respect to rocks, in particular, it is very rare that homogeneous rocks are distributed uniformly. In general, geological conditions are distributed in a wide variety, ranging from earth, sand, soft and medium rocks to hard rocks. Under these geological conditions, when planning of the tunnel construction is to be made out, either blasting method or tunnel boring machines must be selected taking into consideration the geological structures along with the designed tunnel route,' possibility of encountering aquifers, hardness of rocks anticipated and also, the adjacent environ- mental conditions. In the process of select- ing an excavation method,, it is important to make a comparative investigation between the above two methods considering the advantages and disadvantages with regard to the respective operating efficiency, economical efficiency and the conditions and scope of application as well. Furthermore, in addition to these considerations, the recent environmental restriction, which does not allow the blasting in the surroundings of residential areas, must also be taken into account. Because of this, in some cases there is no alternative but to use a static excavation method or a tunneling machine even when these are less efficient than blasting.

Jan 1, 1987

By Jones A

Today there is a vast amount of information available relative to the performance of tunnel boring machines, and associated systems. The data referred to here consists of project reports, manufacturer's equipment literature and papers concerning almost every aspect of the excavation process. Why is it then, that many projects that employ full face tunnel boring machines (TBMs), on average perform significantly less than the peak performances reported in this industry?

Jan 1, 1993

By Robert B. Hoekzema

This Bureau of Mines report describes the history, characteristics, distribution, and mineral development potential of 21 lode gold deposits in or near the Chugach National Forest (CNF), AK. It includes findings from a 4-yr (1979 to 1982) mineral evaluation of the CNF conducted by the Bureau and the U.S. Geological Survey (USGS). This evaluation, undertaken to provide the U.S. Forest Service with mineral resource data for use in making decisions on land use, included site-specific mapping and sampling of more than 200-lode gold deposits. The data presented here were compiled from the findings of this 4-yr evaluation and from existing literature. Fourteen of the 21 lode gold deposits described in this report contain a combined identified resource of 117,750 short tons (st) averaging 0.55 oz/st Au and 0.2 oz/st Ag. Two mineralized felsic dikes in the Summit Lake-Palmer Creek area contain a combined identified resource of 18 million st grading 0.02 oz/st Au and 0.16 oz/st Ag. Identified resources were not determined for the remaining five deposits because of a lack of information.

Jan 1, 1987