Search Documents

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By R. V. Ramani, S. Shankar

"A convective dispersion model has been utilized to calculate the real-time airborne dust concentration in mine airways using re-entrainment as the only source term for airborne dust. It incorporates two important sources of re-entrainment in mines -- air velocity and movement of objects. The model has a sink term accounting for the deposition of particles along the airway. The model is solved using a finite difference scheme which is coded for computer. The computer model outputs airborne respirable and total dust concentrations along the airway as a function of time. The real-time and average gravimetric concentrations from several in-mine experiments were compared with the results from the simulation of the experimental conditions. This model can be used for estimating airborne dust entrainment due to air velocity, equipment movement, and persons walking. INTRODUCTIONEdwards and Ford (1988) developed a model for coal dust explosion suppression and utilized a predetermined value of threshold velocity for flowing air to pick up dust from floor. Depending on the strength of the removal forces, re-entrainment can increase the airborne dust concentration in mine airways. The most prevalent forces causing re-entrainment in mine airways are the drag and lift forces due to flowing air, and removal forces due to the movement of persons and vehicles. Shankar and Ramani (1991) have investigated the unique characteristics of the re-entrainment phenomenon in mine airways. Experiments on re-entrainment of coal dust particles were conducted in mine airways, and in a wind tunnel (Shankar and Ramani, 1994a, and 1994b). The results from the two experimental studies were found to compare well (Shankar and Ramani, 1995). There is no reported model to determine the airborne dust concentrations due to airflow or persons walking under conditions existing in mines. The present study is a part of a continuing research project in the Generic Mineral Technology Center for Respirable Dust on the spatial and temporal behavior of airborne dust in mine airways (Ramani, 1983)."

Dec 1, 1996

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rockmass strength. Past studies have largely used arbitrary scaling approaches to produce rockmass strength from laboratory rock tests. This paper proposes a stochastic approach to produce rockmass strength from laboratory rock tests. Based on the laboratory data, MATLAB with an extreme value stochastic model generated a database for each physico-mechanical property of the rock. Then finite-difference software FLAC2D simulated laboratory-sized rock specimens. Random material properties in MATLAB were generated using the grids developed in the numerical model. The random properties were then applied to the final FLAC2D model. Model runs simulated the approach performed in the laboratory. The results from the model indicate that a stochastic approach produced compressive strengths that were lower than those from the deterministic approach. Failure modes for each specimen were different from those observed in the laboratory. In addition, random density also influenced the failure mode, highlighting the importance of stochastic analysis in rocks.

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By Armstrong

This is a world of change and has been from the beginning. There are constant efforts on the part of natural forces to wear down the high spots and fill in the low spots. Wind and water over eons of time tunnel through obstacles and build windways and waterways to make movement of air and water easier and more efficient. It is a natural, never ending, ever changing continuing effort. Man in his struggle to survive, and to progress, has had to adapt the terrain of the earth to fit his needs the best he could. First, he used natural caves to protect him from the elements; then he learned how to build earth and rock-moving tools from antlers, bone, rocks, and sticks and adapted his cave to increase his security and provide better protection from heat and cold and from his predatory enemies. As his numbers increased, so did the necessity of further adapting his environment to accommodate his needs. Water was usually not available when and where needed, especially in the desert areas where civilization developed, and long tunnels were drilled to intercept ground waters and lead them to underground caves carved out of soft limestone. Most of the tunnels of early man were to bring water from where it was to where man needed it. Then, as now, as man increased his chances for physical survival, he turned to the quality of life -- and this reflected in the concern for life after death. This lead to the elaborate shafts and tunnels for the protection and prservation of the more affluent noblemen and pharaohs of the early Egyptian civilization. Man used the underground for the stable temperature and for protection and safety.

Jan 1, 1974

By Dougal R. McCreath

The storage of energy in one form or another is a well established practice, demonstrated by the familiar sight of large oil storage steel tanks. Today, however, the problems of energy storage are taking on a new complexion. Increased emphasis on large and sometimes untried forms of energy storage is being generated by: (1) The uncertainties we face concerning future oil and gas supplies. (2) The growing need for the storage of peak-shaving energy on large utility systems. (3) The growing volume of highly toxic and energy generating wastes resulting from nuclear power plants. Concurrent with the growth of these pressures, legitimate environmental concerns now demand that the methods of storage which are utilized meet adequate criteria of safety and preservation of surface land, as well as fulfilling technical and economic functions. From these elements, increasing awareness has grown of the potential role that can be played by underground space in providing a storage medium for energy related materials. The vessels which must be built for underground energy storage will be built by the tunnel engineer, and the design requirements of such vessels will go far beyond the classical tunneling requirement to drive a stable, reasonably dry tunnel between two points. Depending on the nature of the material to be stored, the manner in which the storage is to be operated, and the specific risks to the environment which are involved, rock chambers must be designed as special purpose storage vessels. The tunnel engineer may be required to demonstrate that unusual pressure and temperature conditions can be sustained by the rock, or that containment of a toxic material can be assured. In certain cases there will be emphasis on

Jan 1, 1976

By R. Dawson Hall

THE stresses in the e simplest structures are often those we find most difficult to analyze. The most complex condition in mine stresses is found in simple tunnels where the roof, the sides, and the floor are a monolith. The functions of the parts are like the parts themselves not distinct and specialized, and the problems to be solved are like those in a metal structure with riveted joints or a redundancy of bars. This difficulty explains perhaps why the condition has not been treated. But just because it cannot be discussed in its entirety is no reason why it should be treated as an action of parts with specialized functions as a roof 'beans with supports and a foundation. The problem cannot be ignored on the ground that it is not of sufficient importance to warrant careful consideration, because conditions of complete monolithism, of which the tunnel is the type, are found materially unchanged) in room-and-pillar and in longwall work. This unity between roof, sides, and floor, which to the coal miner is a difficult conception, really deserves a scientific appellation, and perhaps holoid (from holos, whole, and eidos, form) will serve the purpose as well as any other. In a simple tunnel the roof, the sides, and the floor form integral parts of one and the same structure; and the distortion of one cannot be conceived without a consequent strain in the others. Thus when the roof of the tunnel droops by reason of its weight, the upper parts of the sides are drawn in because they are integrally-connected with the roof and must approach each other whenever, by the sagging of the roof, the distance between any two points in it is diminished. (See Fig. 1.)

Jan 9, 1915

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

By Richard L. D?Arcy

This paper describing the mining practice and methods at the United Verde Extension mine, Jerome, Ariz., is one of a series of papers in preparation by the Bureau of Mines presenting the mining methods used in various mining districts of the United States. The United Verde Extension mine is a massive, high-grade deposit of copper sulphide containing some gold and silver and is mined almost exclusively by the conventional square-set method with some local modifications. About 450 men are employed underground and 1200 tons of direct smelting ore is produced per day. Figure 1 is a surface map of the Jerome district.

Jan 1, 1930

By L. Giraldo, S. Cotten

"INTRODUCTION The vision for a “Mine Escape Vehicle” (MEV) is to provide capabilities to better enable underground travel to allow miners to escape to safety in the event of a major mine emergency such as a fire or explosion. Enhanced transportation and survival capability such as a MEV may have minimized or eliminated the loss of life associated with several of the mine disasters that occurred in 2006, which together resulted in the deaths of 19 miners. Although the most desirable response in an emergency is for the miners exit the mine, if escape proved to be impossible, the miners could use the vehicle to proceed to an underground point of refuge to await rescue. Under a NIOSH contract issued in April 2008, Raytheon developed a conceptual vehicle design including (1) the capacity to provide life support functions for a number of miners, (2) operate in a reduced oxygen atmosphere with little or no visibility, and (3) travel at speeds faster than miners could walk out of the mine. The proposed MEV concept envisioned modification of a personnel carrier (a.k.a. a “mantrip”) that would be used every day during normal mine operations, not a specialized vehicle reserved only for or dedicated solely to escape. The MEV concept also included escape aids that are detachable from the vehicle in the event that the vehicle must be abandoned on the way out of the mine and the dismounted miners had to proceed on foot. To advance MEV development, NIOSH awarded a second contract in 2010 to Raytheon to build, test, and evaluate the performance of a proof-of-concept MEV that culminated in a 7-month performance evaluation of vehicle in an Eastern Kentucky coal mine (Figure 1). User feedback and lessons learned from the proof-of-concept vehicle evaluation provided support for the general MEV approach, guidance related to the practicality of MEV capabilities, and indication of specific technology shortcomings for this application."

Jan 1, 2015

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By Robert Hopler

THE KEYSTONE NATIONAL POWDER COMPANY is an Independent organization, incorporated under the laws of the State of Pennsylvania. It has three dynamite mills near Emporium, Pa., with a daily capacity of 165,000 pounds. It maintains branch offices in practically all the largest cities east of the Rocky Mountains, and has distributing magazines located in every section where there is a demand for high explosives, with facilities for wagon deliveries. Our mills are all of modern type and are equipped with the most improved machinery for the manufacture of high explosives. The efficiency of our laboratory in conjunction with the high class of labor employed, has enabled us to put on the market an explosive, the quality of which is the result of extensive research and scientific knowledge. Our modern and complete equipment for harbor and railroad transportation insures our patrons of prompt deliveries, which is an essential feature particularly to contractors and those whose facilities for storage are limited.

Jan 1, 2013

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012