Search Documents

By deur R. Dippenaar

'n Kort kursus oar die teorie en praktyk van hittebehandeling is vanaf 29 Junie 1981 tot 3 Julie 1981 in die departement Materiaalkunde en Metallurgiese Ingenieurswese aan die Universiteit van Pretoria aangebied. Die kursus is dour dosente van die departement opgestel en in samewerking met 'n aantal gassprekers aDder beskerming van die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie aangebied. Tunnelling The Third International Symposium on Tunnelling is to be held in Brighton from 7th to 11th June, 1982. Professional development seminars The Department of Mining and Metallurgical Engineering of McGill University is to hold the following seminars during 1981-1982.

Jan 1, 1981

By Roy J. Leonard

Two small diameter sewer tunnel projects being hand dug under major highways in the Greater Kansas City area encountered problems which were unforeseen from the geotechnical engineering information supplied with the contract documents. Both tunnels were being excavated by experienced crews using steel liner plates. One required the use of compressed air for completion, while the other required poling boards. Both contractors overran their budgets and filed changed condition claims, and this promoted further geotechnical engineering investigations. Fissured clays beneath a water table were encountered at both sites, but the character of these clays differed; however, both were inadequately described in the original geotechnical engineering reports.

Jan 1, 1987

By Karl Kuhnhenn

One substantial element of the NATM is to take into consideration the geotechnical rock behavior in the design of excavation and support methods. Even if this opinion is being shared increasingly, the stress analysis is not the sole criterion for a successful tunnel drive. By the beginning, the inventors of the NATM have clearly defined a number of principles which have kept their validity until now. The evaluation of different failure cases demonstrate how necessary the observance of these principles and their strict following during execution are besides the stress analysis. The great number of successfully excavated NATM tunnels are an impressive evidence for these principles.

Jan 1, 1995

By Erland A. Tillman

The U.S. National Committee on Tunneling Technology under the aegis of the National Academy of Sciences has long recognized that productivity in major underground construction projects could be increased through better contracting practices and better management. Between 1974 and 1978, this Committee has prepared three reports on these subjects. This paper reviews these reports and their recommendations. It covers the extensive actions by the U.S. National Committee on Tunneling Technology to bring the recommendations to the attention of leaders in the underground construction industry and thus further their adoption and implementation. These activities are continuing. Visibility in this session will give these reports and recommendations increased exposure.

Jan 1, 1981

By Lee W. Abramson, Glenn M. Boyce

A dowel testing program was conducted as part of the Interstate Route H-3 Trans-Koolau exploratory tunnel project on the island of Oahu, Hawaii. The testing evaluated the performance of dowels to be used as initial ground support for two 12- by 15-meter (40- by 50-foot) tunnels within weathered basalt. The program tested four dowel types of three different lengths. Both grouted and friction dowels were tested. The program determined which dowels were more effective in carrying load and noted any special procedures that would be required during construction. This paper presents the test results and discusses how these results were used in the design.

Jan 1, 1991

By L. L. Oriard

The author describes three case histories of fracture-control blasting demonstrations. This is a technique in which the walls of blast holes are scribed or notched in order to enhance the development of blast_induced fractures, and to control their direction. One demonstration was that of a tunneling application in a rock that was generally competent but strongly foliated, hence strongly anisotropic. P second test was conducted for perimeter blasting of a structural excavation in a massively jointed limestone. A third field test was conducted for tunneling through an old concrete structure. Increased applications are envisioned with new tool modifications being developed at the University of Maryland.

Jan 1, 1981

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By Paul Gribbon, Greg Colzani, Jim McDonald

The $300 million West Side Combined Sewer Over?ow Project consists of over5.5 kilometers of soft ground tunnel, an 833-million liter per day (220-MGD) deep shaft pump station, 3 kilometers of micro tunneling, and other miscellaneous shafts and pipelines. The construction contract, underway since September 2002, is a reimbursable cost plus fixed fee contract that included a quali?cations-based contractor procurement process and has undergone some modi?cation since execution. This paper will describe the contractual issues addressed to date, dispute resolution, where improvements can be made, and how an Owner can evaluate whether this type of contract is the best approach for an underground project.

Jan 1, 2005

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the State's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the state's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By Ramon LaRusso, Frank Wheby, Richard Acker

Field investigations and office studies were used to develop criteria and cost parameters related to the geologic aspects of the proposed project. These results were employed in optimization of layouts and comparison of alternative schemes, leading to selection of the recommended program. Study of project features included the development of subsurface shafts, tunnels, and mined storage areas, and the utilization of existing surface quarries. These project features were proposed for construction within the bedrock units underlying Chicago. Principal geologic considerations included bedrock structure, stratigraphic sequence of units, rock competence and uniformity, and requirements for aquifer protection. All geologic factors were interrelated with other project considerations such as surface hydrology, hydraulics, and urban setting. Data for analyses was acquired through an exploration program conducted intermittently between 1967 and 1971, in addition to that already available through numerous explorations and well constructions in the project area. The exploration program included seismic surveying, core drilling, geophysical borehole logging, and water pressure testing of boreholes, and water well drilling and testing. Extensive laboratory tests were conducted on core samples. The data formed the basis of studies enabling the formulation of preliminary design and siting criteria resulting in construction cost evaluation.

Jan 1, 1997

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019