Search Documents

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed, wire-mesh screen at different airflow rates in one-phase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity, non-Darcy, single- and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulae on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By Shelby Z. Palya

"INTRODUCTION The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publicatioll3 and articles, from January 1, 1960, to December 31, 1964,4 from January 1, 1965, to December 31, 1969,5 and from January 1, 1970, to December 31, 1974; 6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1975,7 from January 1 to December 31, 1976,8 from January 1 to December 31, 1977,9 and from January 1 to December 31, 1978.10"

Jan 1, 1980

By T. Dimillo, R. G. B. Pickeirng

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular ore bodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focussed on the haulages, cross cuts and raises. The non-explosive rock breaking method has many other applications, however, it is the integration with the Tunnel Digging Machine that results in the first, cost effective, Continuous Tunnelling Machine for hard rock mining.

Sep 1, 2001

By Edward (Ted) M. Dowey

Shaft 26B of New York City’s Third Water Tunnel was constructed by Frontier-Kemper Constructors, Inc. of Evansville, Indiana. The 176.8 m (580 ft) deep shaft will serve as the construction shaft for the Manhattan spur of Water Tunnel No. 3. Twelve m (40 ft) of over-burden was supported by a rectangular cofferdam. This shaft was excavated in 13 months, through 164.6 m (540 ft) of rock, using 24,040 kg (26.5 tons) of explosives. Concrete lining cycles included the installation of stainless steel pipes embedded in the lining as the shaft advanced. A total of 635 m (2,084 linear feet) of stainless steel pipe was installed.

Jan 1, 1997

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By Julian S. Edwards, C. Frederick C. Pearson, Sevket Durucan

Information gained at the site investigation stage of the Carsington aqueduct project led the designers to suspect that methane might be encountered during tunnelling and therefore gas detection techniques, including emergency shutdown systems, were introduced. After construction, on completion of the excavation and lining of the tunnels, a survey showed that methane was entering the aqueduct dissolved in infiltrating groundwater. General body air concentrations were very low but on closure methane concentrations rose rapidly within the aqueduct. A research project has now been initiated to investigate the mechanism of methane generation and entry rate into the system, the results of which are being taken into account in the preparation of future operating procedures.

Jan 1, 1989

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By Albert H. Fay

This glossary is published by the Bureau of Mines as a contribution to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining., quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; and geological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and. the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted.

Jan 1, 1920

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

By E. P. Carman

1. CARMAN, EVERETT P., OPPERMAN, MARTHA, NISHIYANA, SALLY, AND RACOOSIN, LEE. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1945 to 1950. B. 528, 1954, 60 pp. 40 cents. 2. ROSE, HAROLD J. Industry-Sponsored Coal Research in the United States. Chap. in Proceedings: Fifth International Conference of Directors of Mine Safety Research. B. 489, 1950, pp. 9-12. $1.25. Minerals Yearbook 3. STRINER, HERBERT E., CARMAN, E. P., AND GOODING, RICHARD M. Review of the Mineral-Fuel Industries in 1952. Minerals Yearbook 1952, Fuels, vol. 2 (pub. 1954), pp. 1-28.

Jan 1, 1958

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

By K. F. Unrug

Extrapolation of the rock properties obtained from the cores exploration holes to the surrounding areas often causes problems because of frequent sudden changes in the geologic composition of strata. To address this problem, the author has been developing a method of rapid strength testing "in situ," with application of a borehole penetrometer. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. The results are generated by strength determination on the wall of a drill hole at a site. The newest development is a borehole penetrometer that requires only a 1.38.mm (1.5 in) diameter hole. The small diameter of the penetrometer body allows for drilling test holes with production mine equipment such as roof bolters. It opens the possibility of broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 1999

By Henry R. Tiedemann, William H. Hansmire, Harvey W. Parker

Although the use of precast concrete segments for tunnel linings has been common for many years in Europe, acceptance of this type of lining has been slow in the United States. This paper explores the cost, design, and construction considerations of concrete segmental lining with a view to promoting its use in this country when favorable conditions exist. The different perspectives held by owners, designers, and contractors are discussed. In addition to cost, other considerations include previous design and construction experience, size, length and function of tunnel, watertightness, and liability. Cost comparisons are made to traditional ground support and lining. Under favorable conditions, the use of precast concrete segmental linings can be technically feasible and cost effective.

Jan 1, 1987

By Alan M. Muir Wood, Gerhard Sauer

There axe two essential features of administrative practices in tunnelling in order to provide proper encouragement to innovative and economic tunnelling: first, that there should be a continuity in the decision making at all stages so that the full implications of decisions in early stages of planning and design are understood; second, that there should be appropriate provision for variation so that the greatest possible benefit can be derived from modifying the working scheme in relation to the characteristics of the ground and from study of its behaviour during execution of the work. Examples are given from the Authors[?] experience as to the benefits to be derived from the application of such principles.

Jan 1, 1981

By Dominic F. Howarth

Groove deepening (deepening of a groove in rock by successive passes of a rock cutting tool) is a potential operational feature associated with tunnel boring machines. Little research has been undertaken in this area which is of direct practical relevance to the design and application of tunnel boring machines. Laboratory experiments using single, double and triple disc arrays have revealed an important fundamental cycle of events associated with disc cutters when progressively deepening a groove. Furthermore, in contrast to pick cutters, groove deepening by discs is shown to be an efficient operation. This can be directly attributed to the increased interaction between disc cutters due to the increase in magnitude of lateral forces generated as a groove is deepened.

Jan 1, 1981