Search Documents

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By E. W. Williams

THE Ontario Research Foundation has developed a process for producing low-density steel shapes by direct reduction of iron oxide powders. The process is a combination of reduction, sintering (without compaction), and carburizing, and has been described by Cavanagh (1). Iron oxide powder, in the form of mill scale or highly concentrated iron ore, carefully sized, is poured into a porous mould. A reducing agent, generally coke breeze, is placed around this mould in a heat resistant sagger which is sealed off and heated to 2,000°F. for a number of hours. The coke/ ore ratio, the particle size distribution, the temperature and time of soaking, and the size and shape of the reduced product, determine the densities and carbon contents attained. The Defence Research Board sponsored a programme of research into some of the mechanical properties of the material (which was named Controlled Density Steel) and this paper is an account of various factors which govern the tensile strength of the steel. The ?practically attainable range of density is from 1.5 to 5.5 gm./ cc. but higher densities are obtained on hot working. This paper, however, is restricted to discussion of results for moulded products.

Jan 1, 1957

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

"Despite being a field of study that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world, consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited, while the only contact that undergraduate students have with mining operations during their time of study is usually through shorttime internships or visits in the context of educational trips. Real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes and thus understand the whole picture of mining operations.Indirect practical training is now possible since that technology is shifting from mechanical to digital, and the use of virtual reality — in the context of Mining 4.0 — can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al., 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other, especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers.Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and knowhow could be developed and/or enhanced, are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.An early example of asolely experimental mines is the Luossavaara-Kiirunavaara Mine site operated by LKAB in Sweden, where systematic research on rock mechanics and mining engineering was successfully carried out in the 1980s. As a result, the developed underground mining technology was applied in LKAB’s mines at a later stage. There have also been research mines within collieries such as the former Lake Macquarie Mine at New South Wales in Australia and the Zeche Tremonia Mine in Germany), but these are no longer in operation (Mischo, 2015)."

Oct 1, 2019

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By R. V. Ramani, R. Bhaskar

"The results .of an experimental and theoretical research study into the spatial and .temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and .normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-1) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.In this paper, comparative analyses of results of the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations.The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the ·comparative analysis results for in-mine experiments. Specifically, the model· predictions for an 800-meter stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper."

Aug 31, 1989

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By Robert M. Cox

Systematic roof bolting has proven to be a very effective method of mine roof control; however, major roof failures still occur and roof falls still remain the number one occupational hazard of underground miners. Why do some bolted mine roofs fail, while the vast majority of bolted mine roof remains stable and safe to work under? Observations of numerous roof failures indicate that most of the major roof failures* are associated with either: 1) Jointing, faulting or other structural fracture zones; 2) massive shale beds of lenticular structure, or 3) thinly laminated sand-shales. The jointing and faulting present an obvious weakness in the roof rock structure; whereas, the massive shales and laminated sandy-shales create a roof structure with low shear strength and/or modulus of deformation. An observation of major significance is that most bolted mine roofs fail as a unit, and that the thickness of the fall is roughly equivalent to the roof bolt length (See Figure 1). In fact, several operators have experienced the phenomenon of an increase in roof fall thickness with an increase in roof bolt length.

Jan 1, 1973

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010