Search Documents

By Walter W. Bradley, OLAF P. JENKINS

IN April of this year the California State Division of Mines (formerly known as the State Mining Bureau) observed its 50th anniversary. The Division serves as a bureau of information and, an encyclopaedia of California's economic minerals. Its primary function is to make economic surveys of the mineral resources of California, their development and utilization. Geological studies also constitute a related part of the work as being necessary in tracing and out- lining ore deposits and the most likely areas in which to find them. The results of the Bureau's data-gathering are published in the form of annual reports of the State Mineralogist, and in bulletins on specific substances. The Division is just completing a series of reports on the mineral resources of the State arranged by counties.. It is now starting .a new series of reports arranged according to substances particularly the so-called non- metallic commercial groups. Of these the following are now available: clays, barite, and mineral paint. These will be followed by reports on feldspar and silica, diatomaceous earth, limestone and others

Jan 1, 1930

By Morton Macartney

FOR many years the developers or owners of worthy mining ventures in need of financing have found it almost impossible to obtain such financing under the conditions existing in most other lines of business. High rates of interest and unfair participation in profits have robbed the developers of much of their holdings, and have resulted in over-capitalization and many other like evils. When the general financial condition of the country is bad, this difficulty increases to a point where many operations must cease and hen are thrown out of employment. In 1.934 this situation had developed to such a point that Congress attempted to aid the mining industry. It first authorized the RFC to make loans to recognized and established corporations, individuals, and partnerships engaged in the business of mining, milling, or smelting of ores in June, 1934, limiting such authority to loans adequately secured, the security to consist of mineral acreage. The requirements of the law were stringent and of the 252 requests for loans received up to June 1, 1935, 35 were authorized.

Jan 1, 1936

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942

By Arthur S. Huey

AS the end of the collegiate year approaches, the problem of student employment again becomes acute. This subject divides itself into two phases: (1) employment prior to graduation and (2) employment following graduation. "Experience is the best teacher," according to the old adage, and the student needs all that he can get. He is afforded every opportunity to reap from his books the theories and principles of scientific and engineering practice, and occasionally he is privileged to make field trips to observe the practical side of the subject. But it is not enough for one to know the theory and to observe its application; it is also desirable for the student to get the feel of the tools during his training Such opportunities can only be afforded the student if the major companies cooperate with the universities in giving the student part-time and vacation work.

Jan 1, 1932

By Jay A. Carpenter

FIRST of several sessions at the Annual Meeting devoted to mining methods was a joint program with the Coal Division devoted to the use of Diesels underground. Fred W. Stiefel, in the first paper, stressed the saving in original cost and in operation. Wm. B. Harris then presented the paper of which he was a joint author, and S. H. Ash stressed the poisonous nature of nitrous fumes from Diesel engines even in minute quantity. Determination is difficult but in exhaust gases they are present in amount two to five times that of carbon monoxide. Jay A. Carpenter, in the closing paper of the session, stated that state laws in general prohibit the use of Diesels underground, and that almost all mine inspectors are opposed.

Jan 1, 1942

By R. E. Grant

THE Cerro de Pasco Railway Co., owned and operated by the Corporation, is a common carrier whose chief functions are transportation of ore and concentrates from the mines at Cerro de Pasco to the smelter in Oroya, and haulage of coal from the coal mines at Goyllarisquisga to the coal washery at Fundicion. Connecting with the Peruvian Central Railway at Oroya, the C. de P. Railway maintains joint, daily freight and passenger service from Lima and the port of Callao to Cerro de Pasco, terminal of the C. de P. main line and gateway to the Huanuco Valley. Extending from Oroya to Cerro de Pasco the main line is a standard-gauge roadbed of 70-lb. rail, 132 km. long with a maximum compensated grade of 2.25 per cent and a curvature of 16°, climbing from an elevation of 12,272 ft. above sea level at Oroya, lowest station on the line, to 14,208 ft. at Cerro de Pasco. The highest point reached by the C. de P. is on the coal branch at Alcacocha where the rails are 14,385 ft. above the sea.

Jan 1, 1945

By DFI DFI

An Online Conference

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By K. Best, D. Conn

The US Army Corps of Engineers KY Lock Project in western Kentucky presented the blasters and vibration consultants with a set of unique challenges. The blasters on this project were faced with difficult geology and joint set orientation and sequencing of blasts opposite from what the explosive engineer/blasting specialist had recommended. Combining these issues with strict vibration and air overpressure specifications, blasting as close as 7 feet (2.1 meters) from a new lock wall, site topography that influenced the air overpressure, limitations on seismograph geophone placement that led to anomalies in seismograph recordings; surprising lessons were learned by everyone involved in the project and it is the authors’ goal to share this valuable information with everyone in the blasting industry.

Jan 1, 2024

By Rudy Beltrán, Kellyn Cristobal

El presente trabajo muestra las mejoras realizadas en nuestras operaciones mineras, respecto a disminuir los accidentes que se han venido presentando en diversas minas a nivel nacional, relacionadas al uso de los calibradores para controlar el espesor del shotcrete (concreto lanzado), donde el personal se expone a la línea de fuego cuando el concreto aún se encuentra en proceso de fraguado para alcanzar las resistencias iniciales de sostenimiento. Ante esta problemática, se ha diseñado un mecanismo automatizado que se encuentra adaptado al equipo robot lanzador de concreto, el cual elimina la exposición del personal durante este proceso y ademas asegura la calidad del espesor de shotcrete aplicado en las labores mineras.

Sep 29, 2023

Resistant Tape A new oil-resistant tape for rapid insulation build-up on splices in large power cables has been announced by Minnesota Mining & Mfg. Co. Designated Scotch brand electrical tape No. 25 is made of synthetic rubber providing greater dielectric strength and resistance to high temperatures. The chemical-resistant qualities of the tape make it suitable for use in oil drilling, mining and underground [ ] cable operations, while the 40-mil thickness and extreme stretch (1500 pct breaking point) make possible smooth insulation wraps on irregular surfaces. Dielectric strength is 15,000 v and 10,000 v at 500 pct elongation. It has an electrolytic corrosion factor of 1.0 and an insulation resistance of 100,000 megohms. Circle No. 1 Hydra-Lift The Pitman Mfg. Co. announces that is now has in production a new model of the Pitman hydra-lift, recently-developed crane with hydraulically-powered boom that can be mounted on the frame of any truck, 1 ½ tons or larger. According to the manufacturer, the new model hydralift model B features a variety of improvements over the original production model, introduced late in 1950. Changes incorporated in the new model, according to officials, not only have resulted in improved crane, but also have given the unit a new profile which distinguishes it sharply from the original model. The two chief improvements in the new model are: a big increase in the unit's safety margin and the fact that it is now shipped almost completely preassembled, cutting the time and cost of installation. Rated capacities of the hydra-lift are based on the tipping factor of a 1 1/2 ton truck, with outriggers down, and thus have not been increased. Circle No. 2

Jan 1, 1952

By A. L. Moore

KAISER Bauxite Co., a subsidiary of Kaiser Aluminum & Chemical Corp., has been mining and shipping Jamaican bauxite for over a year. On Feb. 10, 1953 the first boat load of bauxite left Port Kaiser, Jamaica, for the company's alumina plant at Baton Rouge, La. To provide its own source of the aluminum ore, a Kaiser Aluminum & Chemical Corp. exploration party started initial reconnaissance in 1947. This work, and subsequent exploration, led to the acquisition of reserves sufficient to warrant a full-scale mining operation for several decades.

Jan 3, 1954

By R. C. Weed

LEACHING in place at Cananea began in the 1920's on a limited scale. The first plants were small wooden boxes located underground in the Capote and Oversight mines, and output was low. Scrap iron was used as precipitant. Later several other small plants were started up. Leaching was limited entirely to underground areas, and production remained low. The Veta precipitating plant, the first on a larger scale, was put into operation in the late 1920's. After a period of intermittent service it was rebuilt in 1946 and has since been running continuously. In 1943 work on the Colorada open pit was started. This produced 40 million tons of waste, which averaged 0.20 pct capper. When these dumps had aged a few years it was decided to leach them on a large scale, and after considerable research and investigation a leaching system of pumps and pipelines was laid out and installed. At the same time the Ron-quillo precipitation plant was built to treat the copper solutions from the pit dumps. This plant started operation in March 1953. Leaching areas consist of the Colorada pit dumps and various mined out and caved underground stopes. The principal mineral, chalcocite, leaches readily in a weak sulfuric acid solution containing ferric iron. Enough pyrite is contained in the areas to produce an acid-ferric iron solution strong enough to dissolve the copper. Each area is studied to determine the best method of distributing the water over it and the best method of collecting the copper-bearing solutions after leaching has taken place. Water is generally distributed by means of ponds, ditches, and sprays. Spraying has proved the best method of spreading the water evenly; however, in a dry climate some water is lost through evaporation. After passing through the leachable material the solution is collected underground by dams and bulkheads and on surface by dams. An effort is made to give the maximum storage capacity practicable.

Jan 1, 1957

By M Qiao, A Sugden, W Zong, J Hines, J Roberts, T Ren

Long-term exposure to respirable dust continues to present an occupational health and safety hazard to mine workers in underground mines. Workers who are exposed to mine dust can develop occupational lung diseases including coal workers’ pneumoconiosis (CWP) or ‘black lung’, progressive massive fibrosis (PMF) and chronic obstructive pulmonary disease (COPD). To demonstrate the exposure impact of certain working conditions and improve dust management in longwall development panels, this paper details the development of a computational fluid dynamicsvirtual reality (CFD-VR) based training tool. The tool has been developed as an educational platform to facilitate the effective communication of workplace health and safety (WH&S) dust control measures for continuous miner operators and engineers. The study introduces a promising approach to model ventilation and dust flow patterns based on site-specific data, employing computational fluid dynamics (CFD) for a detailed analysis and visualisation of these mechanisms. Additionally, an algorithm has been developed for processing the large and complex CFD data sets into a form amenable for visualisation within a virtual reality (VR) environment using standalone VR headsets with limited processing power. This training tool has been deployed to mine sites with the specific purpose of educating users on the hazards of dust emissions and the best practices for control.

Apr 16, 2024

By S Kodate, Ö Aydan, Y Suda, J Tomiyama

Fracture zones are commonly found in the Earth’s crust. These zones may cause very severe engineering problems. Therefore, the formation and the assessment of the mechanical characteristics of these zones is of great concern for rock engineers. A new double shearing jig was used to study the formation of shear zones in rock under static and impact loading conditions using the device developed by the authors. A series of experiments were undertaken to investigate formation on the formation and characteristics of fracture zones in laboratory. Although actual fracture zones are more complicated, various tests give some insight view of the formation of fracture zones as well as some information on their mechanical behaviour under both dynamic conditions and static conditions. The authors report the outcomes of these experiments and discuss their implications in practice.

Nov 29, 2022

By Park Yun-Seok, Jung Seung-Won, Hwang Nam-Sun, Song Jin-hyuk, Kim Young-ho

This study proposes a new blasting vibration estimation formula that reflects the vibration reduction characteristics of electronic detonators, which are not considered in the current MOLIT blasting vibration estimation formula. Test blasts were conducted across six types of Korean open-pit blasting designs. The results of the test blasts showed that the K value for electronic detonators decreased by approximately 30% compared to electric detonators. Predicted Peak Particle Velocity (PPV) analysis indicated a reduction effect ranging from 30% to 31% across various types. By incorporating this reduction in the K value into the MOLIT blasting vibration estimation formula (K=200), a new electronic detonator blasting vibration estimation formula (K=140) was proposed. Using this new formula, the blasting damage range (R) was calculated under various vibration limits to evaluate constructability improvement. On average, the R value for electronic detonators decreased by about 17%, with significant reductions of around 41% observed for TYPE I under certain vibration limits. In conclusion, the adoption of electronic detonators in open-pit blasting operations improves blasting efficiency, reduces economic costs, and significantly enhances constructability. Electronic detonators have demonstrated superior performance in minimizing damage to safety facilities compared to traditional electric detonators, thereby proving their practicality and effectiveness in blasting operations.

Jan 21, 2025

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Anne Caroline Costacurta Polli, Jose Rojas Cáceres, Roberto Mahler de Morais, Thais Costa Silva

The technology and the knowledge about the behavior of explosives and detonation accessories allowed to create new products for different situations by the restrictions imposed by the market. In a Brazilian underground copper mine the restriction occurred in the use of high grammage Det Cord in the development heading blasts perimeter holes. Enaex Brazil has developed Densiex UG™ (Low-Density Bulk Emulsion), a water-resistant bulk gassing emulsion with a density ranging from 0.60 to 0.90 g/cm³ to replace the high grammage Det Cord in blasts. That product is pumped in the same Mobile Manufacturing Unit (MMU) as Enaex Brazil's standard underground (UG) bulk emulsion. This product has a Lower Velocity of Detonation (VOD), vibration, and detonation pressure, which contributes to a better finishing of the drift, lower impact in the support structures, and lower generation on unstable rocks in the perimeter of the drift. This case aims to summarize the results of the work on the application of the Low-Density Bulk Emulsion in perimeter holes in an underground development gallery at an underground copper mine in Brazil. During this work, 10 horizontal drift blasts were performed using the Low-Density Bulk Emulsion, which presented an average density of 0.64 g/cm³, increasing safety, a 25% reduction in overbreak, a 23% reduction in scaling time, elimination of rework, and a saving of $135,000 per year for this business partner that immediately implemented this new product in all blasts at this mine.

Jan 21, 2025

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008