Search Documents

By Jim Finley, Adam Bedell, Eric Schrader

The CSO 52 Storage Tunnel and Pump Station project consists of 4,700 ft of hard rock tunnel, 2 intakes, and a 4 MGD wet pit pump station. During the geotechnical investigation, it was determined that the host geology contained abundant suldes. The purpose of this paper is to detail the investigation and subsequent determination that acid producing materials would affect the project during construction as well as long-term exposure of tunnel lining and permanent components during the operational life cycle of the tunnel and pump station. Details regarding the interaction between tunnel components and the acid producing material are also provided.

Jun 23, 2024

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By Ruben Piqueras, Juan Luis Magro, Jorge Vázquez, Santiago Martínez, Xavier Manjarín

The Parallel Thimble Shoal Tunnel project involves the construction of a bored tunnel under Thimble Shoal Channel in Chesapeake Bay (VA), between two artificial islands and parallel to the existing tube tunnel, built in the sixties. It will be the first transportation tunnel constructed in the Mid-Atlantic region using a Tunnel Boring Machine (TBM), a 44-foot-diameter Earth Pressure Balance (EPB) named "Chessie," manufactured by Herrenknecht, and which was assembled at the CBBT's southernmost island, with extremely limited room, live adjacent traffic, and difficult access. "Chessie" was successfully launched in February 2023 and this paper describes this complex and challenging process.

Jun 23, 2024

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By David Court, Rab Brown

The paper discusses the work in progress on the construction of the extension of the High Speed Rail line from the Channel Tunnel into the centre of London UK known as the “Channel Tunnel Rail Link” (CTRL), and particularly on contract 250 which involves the construction of two 5.3Km tunnels 7.15m diameter constructed with two EPB convertible tunnelling machines underneath the densely populated area of East London. In addition the paper will look at an innovative Alliance that has been formed between the Contractors and the Client’s Engineer involved in the construction of the London Tunnel Contracts

Jan 1, 2003

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Gary Jackson

Preliminary engineering for the Waller Creek Tunnel was completed in 2001, but the project was held in abeyance until the summer of 2007. This paper describes several features of the revised design, which required significant changes from the original concept. Most notable is the expected replacement of a tunnel boring machine (TBM) by conventional tunneling. The considerable influence of geological conditions on the tunnel vertical alignment is discussed, in particular the impact of the zones of Eagle Ford Shale with swelling potential. Other features which are described include the wide span tunnels and large diameter shaft requirements.

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By A. A. Mathews

During the past year (1967-68), there have been many instances of either partial or complete failure of a tunnel-support system. It looks like the art is in a pretty sad state, but as long as we permit the field of tunnel design to remain basically an art, that's about what we can expect. The application of scientific principles to tunnel design involves much more than assigning values to a series of factors in an equation. I am reminded of the case where the engineer calculated that steel ribs with struts were required to support a horseshoe-shaped tunnel in firm ground. The contractor had driven several hundred feet without installing the struts when the engineer visited the job. When he was informed that the struts had been left out, he fled the tunnel in alarm. As one authority has so aptly put it, "There is far too much calculating and too little observing." Initially, one might think of a tunnel support as a structural member, such as a strut or arch which is installed in order to support some definite load. Similarly, a tunnel lining might be considered as a treatment of the interior surface of the tunnel in order to produce desired aesthetic, hydraulic, or architectural results, or to serve a protective function. Actually, many linings, such as a concrete lining, serve a dual purpose and support a load as well as satisfy other requirements. Not too many years ago a tunnel, during the driving or excavating stage, was considered to be either supported or unsupported. In recent years, however, several techniques have been developed, which by helping the tunnel to support itself, permit the elimination of separate structural support. Since these techniques in many cases actually become a substitute for the conventional types of supports and linings, a state-of-the-art review would hardly be complete without including them for consideration. Thus, for the purpose of this discussion, we shall define tunnel supports as any system or technique which effectively maintains the integrity of the tunnel opening. In their chapters, both Jacobs (No. 6) and Lippold (No. 7) pointed out how support systems have advanced from timber supports to steel supports

Jan 1, 1970

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By Terence G. McCusker, Bruno Dietl

The only previous attempt to use a tunnel boring machine in the rock formations encountered in New York City was unsuccessful. However, technology has been developed since then which made a new attempt a practical proposition. Nine thousand feet each of 8'6" and 11'0" diameter tunnels were driven in Manhattan schist using Jarva TBM's together with 1100 ft. of the smaller diameter driven conventionally in Inwood marble and earth. (1) The selection of tunneling method was largely based on the need to avoid community reaction and hazardous tunneling conditions where the larger diameter tunnel passed beneath residential structures in poor condition in seamy and blocky rock. Experimentation with cutters and cutter mountings indicate that good cutter life and ease of change are available. It was found practical to use unusually large muck cars for an efficient muck disposal system. Conventional tunneling was successfully executed beneath a subway station whose invert was less than seven feet above the crown of the tunnel. Attempts at chemical consolidation and dewatering were unsuccessful in the earth section which was completed under compressed air.

Jan 1, 1974

By William R. Groseclose, Kenneth D. Schoeman

The Buckskin Mountains Tunnel is a key link in the Bureau of Reclamation's Central Arizona Project. The 22-foot (6.7-m) diameter tunnel is being bored in a north-northwesterly direction through volcanic rock near Lake Havasu in western Arizona. The 6.9-mile (11-km) conveyance tunnel will carry up to 3,000 cfs (85 cu m per sec) of water through the Buckskin Mountains as part of the Granite Reef Aqueduct. The water for the project will be drawn from Lake Havasu behind Parker Dam on the Colorado River and pumped some 800 feet (244 m) above the lake to the inlet portal of the free flow tunnel where it begins its 190-mile (300-km) journey to Phoenix, Arizona, and beyond into Orme Reservoir (figure 1). Precast concrete segments are being used as a single system initial support and final lining in the tunnel being excavated by a tunnel boring machine specially designed and built for the job by The Robbins Company. J. F. Shea Company, Inc., of Walnut, California, is constructing the tunnel for the Bureau of Reclamation.

Jan 1, 1976

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

By Yagi Y

The double track railway tunnel, called the Second Shirasaka Tunnel is being constructed under the supervision of Japanese PTational Rail- ways (JNR) in the tertiary soft rock strata in order to speed up the railway transportation. This tunnel (L=1765m), located in a central part of Japan, is excavated by the machine (roadheader), while the adjoining First Shirasaka Tunnel (L=1296m), completed five years ago, was driven by the blasting, and NATM is adopted in both tunnels. The geological features in this region are Neogene Tertiary of Miocene sediments consisted of mudstone, the sandy mudstone and the alter- ation of these rocks, having a squeezing be- haviour. And the geological structure is as complicated as some anticline and syncline structures, large or small scale exist, and as a lot of faults are found. The machine excavation manner using road- header is adopted in this tunnel to minimize the effect of excavation because there is a possibility of the occurrence of landslide due to the tunnel excavation, and also because local inhabitants reside on the ground surface.

Jan 1, 1987

By Robert J. Whiteley, Colin Parker

Two major tunnel projects with a combined value of about $US700 million have been recently completed in Sydney using both soft ground and hard rock Tunnel Boring Machines. The first of these and the main entry in Australia for the Year 2000 Olympics was the New Southern Railway. This is 10 km of mainly soft ground tunnel linking the Sydney’s International Airport with the Central Business District. The second tunnel was designed to alleviate major stormwater pollution of Sydney Harbour and involved construction of the Northside Storage Tunnel. This is19 km of hard rock tunnel at depths exceeding 90 m that connects many of the northern Sydney suburbs of Sydney with the North Head Ocean Outfall. Case studies of these projects describe the use of innovative geophysical technologies comprising gravity and seismic tomographic imaging with geotechnical testing at the feasibility and design stages. This approach minimised construction and financial risk by effectively quantifying the significant geological and hydrogeological issues along these tunnel routes that exerted major controls on these projects.

Jan 1, 2001

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005