Search Documents

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By James Warner, Peggy Ganse, Glen Smoak, Raymond Henn, Sam Bandimere

Over the past several decades, cement-based grouts using ultrafine cement as are placement for portland cement have begun to gain acceptance as an alternative to chemical solution grouts, however the amount of information currently available on these grouts is limited. For this reason, the authors developed a field testing program to evaluate the penetration capabilities of various ultrafine cement grout mixes. The tests were conducted by injecting sand columns using different portland and ultrafine based grouts, the measuring penetration distances after applying equal injection pressure for the same time period. Results of tests performed in 1999 and 2000 are discussed herein.

Jan 1, 2001

By Chas. F. Jackson

This bulletin is one of a series of Bureau of Mines reports dealing with mining methods, practices, and costs. A study of this subject was undertaken by the Bureau in cooperation with a large number of mining companies in 1928. This study continued for 5 years, during which engineers of the Mining Division of the Bureau visited most of the larger mines and many smaller ones in the United States, as well as several mines in Canada and Mexico. As a result of this study, 75 reports dealing with underground mining methods and costs at different mines were published as information circulars. Circulars also were issued on 6 open-pit mines and 2 gold-dredging operations. These circulars were written by the managers, superintendents, and engineers in charge of the operations, in some instances in collaboration with Bureau engineers. They were prepared according to a standard outline drawn up by the Bureau to obtain uniformity in textual treatment and in the arrangement and basis of setting up cost and operating data.

Jan 1, 1936

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By F. H. Willcox

This publication is the third of a series of reports on hazards and the prevention of accidents at blast-furnace plants that is being published by the Bureau of Mines, Technical Paper 106a being the first and Technical Paper 136b the second of the series. This bulletin, which is arranged in three parts, treats of the causes and prevention of blast-furnace breakouts, explosions, and slips. The first part discusses blast-furnace breakouts, the hazards therefrom, causes, and features of furnace design and methods of operation that tend to prevent breakouts or lessen their number, and points out safety measures to be adopted. The second part takes up the theory and causes of gas explosions at blast-furnace plants and reviews the better methods in use for handling gas. The third part analyzes the causes of hanging and scaffolding in blast furnaces, with the resulting slips that frequently cause injury to the plant and danger to the workmen, describes features of construction and furnace design and methods of operation employed to prevent hanging and slipping, and suggests precautions and safeguards.

Jan 1, 1917

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

To meet the energy requirements, hydroelectric projects are planned and executed in many countries. Though these projects requires a high capital investment, the returns are regular with minimum maintenance after commissioning of the project and are ecofriendly. Bhutan is situated in the eastern Himalayas and covers an area of 38,394km2 (14824.01sq. miles. It is bordered by India in East, South and West and by Tibet in the North. The hydropower potential of the country is estimated at 30,000MW, out of which around 5% has been harnessed.

Jan 1, 2016

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Wolfgang Gütter

India is targeting to boost its electrical capacity from 100 GW to 200 GW within the next 10 years. The National Hydroelectric Power Corporation (NHPC) has decided in2001 to take execution of the 800 MW Stage-II of the prestigious 2,051 MW Parbatihydrol electric project in Kulu district of the northern province Himachal Pradesh. Two parallel 30° inclined underground pressure shafts of 1.542m in length each will be excavated in different geological formations and lined with hexagonal concrete segments by a hard rock double shield TBM. That kind of heading will be a novelty to India and an innovative method for inclined pressure shafts. The 4.88m Mitsubishi DSTBM will be assembled underground on a swivelling steel platform especially designed for the launching as well as for the acceptance of the TBM in the upper cavern of each shaft. The hexagonal segmental lining system causes a significant higher job safety than an open TBM with conventional support. Each ring consists of four honeycomb segments with 20 cm thickness. After finalisation of the excavation a steel liner will be installed and concreted. The Joint Venture Jäger-Seli will perform the two pressure shafts as a sub-contractor for the Indian company Gammon India Ltd.

Jan 1, 2005

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000