Search Documents

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

By C. C. Li

Traditionally, strong and stiff devices, such as fully encapsulated rebar bolts and concrete lining and arches, are preferred for underground rock support. The attention is paid to the strength of the devices in such support designs. It has been observed in engineering practice that support systems composed of stiff devices are often subjected to premature failure in high stress rock conditions. In the past decade, yield support devices have been employed to improve the performance of rock support systems. A rock support system usually consists of both internal and external devices that are installed within the rock mass and on the free surface of the rock, respectively. Great efforts have been made to make support devices yieldable in the past years, but the efforts are focused on different aspects in the tunneling and mining branches. In the tunneling branch, the focus has been put on the development of external yield devices, such as Lining Stress Controller (LSC), Honeycomb element and compressible concrete, which are embedded in shotcrete liners, while in the mining industry the efforts has been on the development of yield rockbolts, such as the cone bolt and the D-Bolt. The internal and external support devices are not compatible in their deformation capacities in the current rock support systems even though yield devices have been employed. All the devices in a support system should be deformable and compatible in deformation capacity. With such a support system, premature failure of individual support devices could be avoided and the service life of the support system is prolonged. It is a trend at present to take into account the energy absorption capacity, instead of simply the strength, of support devices in rock support design.

Jan 1, 2015

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By Theo. A. Link

ACCORDING to our office dictionary, geology is "the science that investigates the structure of the earth and its successive physical changes", and a geologist is "one who knows the science of the structure of the earth". No doubt this definition does not suit all of us. Another dictionary would have the definition slightly different. As an example, one dictionary stated that "a geologist is one who practices geology". (Some of our clients told us to quit practising and get to work). There are many different types of geologists engaged in various branches of the profession and some of these are further broken down into subdivisions so that specialization is becoming more and more prevalent. As a result it is, in some cases, doubtful whether or not we are actually dealing with a geologist in the generally accepted sense of the term.

Jan 1, 1956

By Neil J. Sullivan, Goode. George E.

"The Adams mine, operated by Jones & Laughlin Mining Company, Ltd. and located near Kirkland Lake, Ontario, produces one million tons of iron ore pellets per year. This paper briefly describes the mining and concentrating operation and deals mainly with the operation of the pellet plant. The orebody consists of fine-grained magnetite and some hematite, with alternating layers of chert, and is mined by conventional open-pit methods. After crushing and grinding, the ore is concentrated by magnetic separation and flotation. Agglomeration is accomplished by the grate-kiln pelletizing process. The plant layout and general operation will be discussed in detail."

Jan 1, 1968

By P. R. Jones

"The paper describes the CDN$400 million expansion at Hudson Bay Mining and Smelting Co., Limited’s operations. The company has continuously produced copper and zinc at the Flin Flon metallurgical plant since 1930. The paper details the company’s operational turnaround since 1995 and “The 777 Project” which includes two new mines, expansion and modification of the concentrators, expansion of the zinc pressure leach plant, a new zinc electrolytic cellhouse and modifications to the copper smelter gas handling system to reduce ground level gas emissions. IntroductionHudson Bay Mining and Smelting Co., Limited (HBMS) was incorporated in 1927 to mine and process the world-class Flin Flon copper and zinc orebody. Ore concentration and metallurgical facilities were constructed in Flin Flon. The metallurgical complex capability is currently 89 000 tonnes of copper metal and 98 000 tonnes of zinc metal from both HBMS and purchased concentrates.Flin Flon, with a population of 7000, is in Manitoba and partly in the province of Saskatchewan. The location is isolated with Winnipeg 800 km to the south and Saskatoon 500 km southwest.Today, three underground mines feed the Flin Flon concentrator, one feeds the Ruttan concentrator at Leaf Rapids, 200 km to the north of Flin Flon, and Chisel North mine feeds the Snow Lake concentrator (Fig. 1).The Flin Flon volcanic massive sulphide proximal and distal orebodies are within the Flin Flon greenstone belt which stretches from the west of Flin Flon to the east of Snow Lake, a distance of 250 km. The belt is approximately 100 km wide before disappearing below the paleozoic cover to the south."

Jan 1, 2001

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By J. Hall Carpenter

"Wet concentration has, in the history of ore dressing, been the primary treatment method following crushing, grinding and sizing, when these have been necessary. The evolution of new methods of gravity concentration has been comparatively slow.Today, the most significant and sophisticated of the new types of gravity concentrators is, no doubt, the cone concentrator developed by Ernst Reichert of Mineral Deposits Pty. Limited in Southport, Australia. These units have now had some years of use in the field, are becoming one of the standard tools of the industry and their metallurgical results, as outlined in this paper, are out-standing."

Jan 1, 1966

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric 'designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951