Search Documents

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills' grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly

"A numerical model has been developed to study macrosegregation associated with liquid feeding in the Low Pressure Die Casting of A356 aluminum alloy wheels. The model of the wheel casting process has been implemented within the commercial CFD software package, FLUENT, using a User Defined Function (subroutine) to account for Si rejection based on the Scheil approximation. The model has been validated against temperature and microstructural data taken from a commercially cast wheel. The amount of segregation in the wheel has been shown to be significant in a couple of key areas. The implications of accounting for segregation include an improved ability to predict shrinkage porosity, fatigue performance and potentially also hydrogen porosity.INTRODUCTION The aluminum alloy A356 is widely used in the automotive and aerospace industries for various components. Examples include automotive wheels, automotive suspension components and airframe castings. Focusing on automotive wheels, Low-Pressure Die Cast (LPDC) A356 wheels offer significant design freedom and are far more aesthetically appealing to consumers than conventional stamped steel wheels. A356 wheels now dominate the market, appearing in all but the entry level offerings of the OEM manufacturers. However, they are typically over-designed to allow for the various casting related defects that degrade their mechanical performance. Thus, their potential to save weight has not been fully realized. Wheel manufacturers are under constant pressure to ensure their products meet strict mechanical requirements (ductility, fatigue, vibration), tight geometric tolerances and high aesthetic quality. The mechanical properties of the final product are determined by the microstructure – e.g. SDAS – and the defect population (porosity and oxides). Depending on their size and location, both porosity and oxides, can act as crack initiation sites reducing fatigue life (Caton, 2001; Jordan, 2010; Wu, 2015). There are a number of examples appearing in the literature (Atwood, 2000; Carlson, 2007; Lee, 2001; Yao, 2011) of numerical models that have focused on hydrogen-based pore formation that have demonstrated an ability to predict porosity formation and pore size distributions in geometrically simple castings. These models assume that the local gas species diffusion through the liquid metal to the pores is the rate-controlling factor of pore growth. Another common source of porosity is liquid encapsulation (Dantzig, 2009). As the pressure within the isolated liquid drops, pores form first due to the pressure dropping below the equilibrium partial pressure of hydrogen in solution and then second grow substantially as the pressure continues to drop falling below the vapour pressure of Al. One factor that can affect both mechanisms of pore formation is species macrosegregation, which has received comparatively little attention in die-casting."

Jan 1, 2017

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By W. D. C. MacKenzie

IT IS almost exactly fifteen years since the discovery of the Leduc oil field and, as this luncheon is part of the Thirteenth Annual Technical Meeting of the Institute's Petroleum and Natural Gas Division, it seems, therefore, a singularly appropriate time to discuss the theme which the program committee has suggested for the occasion -the progress of the Canadian oil industry during the fifteen years since the discovery of the Leduc field. As you will see, I plan to take a few minor liberties with this suggested theme. I shall present ample evidence of growth and progress, but, at the same time, I want to refer to some areas where progress has been anything but conspicuous and to see what can be learned from these areas for the future. The achievements of the Canadian oil industry since the Leduc discovery in 1947 have been substantial, and the public is relatively familiar with the more spectacular developments.

Jan 1, 1962

By K. Johanson, M. Hubert, C. Eckert, D. Ghose

The mining industry routinely processes material with different particle sizes. Coal, nickel ore, copper ore, lignite, shale, and phosphate ore are all examples of materials with wide particle size distributions. It is often assumed that these materials are homogenous and that any particle size distribution has the same chemical activity and composition. It is entirely possible, and quite likely, that chemical composition is a function of particle size distribution. In addition, particle size distributions in ore materials are often responsible for the difference in flow behavior in process equipment. This is evident in coal electrical production facilities. Fine coal may have the same ash content, sulfur content, and BTU value as coarse coal. However, all electrical production facilities know the extreme flow problems that result when attempting to handle wet fine coal. Segregation of these bulk materials is an important issue that must be understood to prevent these cohesive flow problems. Additionally, fertilizers are mixtures of particles with different shape and sizes. These mixtures must remain homogenous to optimize fertilizer performance. Segregation leads to poor product quality. This paper presents a method of measuring the magnitude of sifting segregation occurring in bulk material and the relationship between the strength of the bulk material and the separation tendency. It shows an inverse relationship between the yield strength of the material and the bulk segregation.

Jan 1, 2004

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By P. Condori

Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken. A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material. Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores. This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit.

Jan 1, 2012