Search Documents

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By Daniel J. Schulze

Abstract-Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesiochromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (specifically elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnets in exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2 contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Crpyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By Daniel J. Schulze

Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesio-chromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (speci?cally elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnetsin exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Cr-pyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By Etienne S. Bieler

Mr. Chairman, Ladies and Gentlemen, I come to you tonight distinctly as a physicist, not as a geologist or a mining man. My experience in applied geophysics has been short, and I do not doubt that many of you have a much larger acquaintance: with the subject than I have. A little over a year ago, the firm of Alderson, MacKay & Armstrong decided to investigate the possibility of developing a new method of electrical prospecting suitable to our northern Quebec and northern Ontario conditions, and asked me to take up the work. A preliminary survey of existing literature convinced me that the field of induction methods was most promising. I wish to give you some account of the work carried on last summer in the Rouyn district in this connection with the very able assistance of Mr. H. G. I. Watson. Geophysical methods of prospecting can be divided generally into four classes: magnetic, electrical, gravitational, and seismic. Each class depends on the existence of a definite property in which the valuable mineral to be discovered differs materially from the surrounding rocks. In the four classes, the property will be, respectively, magnetic permeability, electrical conductivity, density, and elasticity. By far the largest differences occur in the case of electrical conductivity, where it is not rare to find ratios of the order of several millions, or even billions, between ores, sulphide ores especially, and the surrounding rock. Hence the sensitiveness and delicacy of electrical methods. Of these four classes, only two, the electrical and the magnetic methods, have been put to extensive practical use in the discovery of metallic ores. The other two classes are important mainly in connection with oil detection.

Jan 1, 1928

By D. C. Peck, H. D. M. Cameron, N. M. Halden, L. S. Jobin-Bevans

Abstract-The late Archean Pipestone Lake anorthosite complex (PLAC) is a 0.9 x 17 km sill-like layered intrusion that is part of a suite of coeval megacrystic anorthosite bodies in the Cross Lake region, northwestern Superior Province. Exploration for Ti-V-Fe oxide mineralization and concurrent geological investigations have contributed to a greater understanding of the lithostratigraphy of the PLAC and its oxide mineralization. Mapping and drill core studies have established a laterally continuous igneous stratigraphy comprising six leucogabbro/anorthosite zones and three melagabbro/gabbro zones. Field evidence, including disrupted blocks of layered units, scour contacts, and size-graded and modally-graded layering, suggests younging towards both the northern and the central parts of the complex. A decrease in the anorthite content of the feldspars from An75 in the south to An30 in the north suggests that the magmas become more evolved to the north. Macrorhythmic layering and gross morphological features suggest that the PLAC crystallized from four major influxes of geochemically similar basaltic magmas. The paucity of magmatic erosional features in the PLAC indicates that layering developed in a relatively static magma chamber, so that in-situ crystallization processes are required to account for the observed petrologic diversity. Drilling has confirmed that a significant Ti- V-Fe resource is contained in two of the four discrete mineralized subzones in the PLAC. Textural evidence and the stratiform nature of the oxide-enriched subzones are consistent with a magmatic origin for the oxide mineralization.

Jan 1, 1997

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By P. A. Mingione

"AEROPHINE@ 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn- and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treating different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.INTRODUCTIONCyanamid operates the only phosphine and phosphine derivatives plant in North America, located in Niagara Falls, Ontario. Specialty chemicals manufactured at this facility are used in many diverse applications, including solvent extraction reagents and textile flame retardants. A unique phosphine-based sulfide mineral promoter, AEROPHINE 3418A, is also produced. The origins of AEROPHINE 3418A promoter date back to the 1960's, when it was established that sulfide mineral collectors based on phosphine chemistry demonstrated efficacy. This new collector chemistry was found to provide flotation performance differing significantly from those of more traditional thiol collector chemistries such as xanthates, dithiophosphates, mercaptobenzothiazoles, thionocarbamates and those with xanthogen groups. Some of the advantages ultimately demonstrated by AEROPHINE 3418A promoter compared to these traditional collectors include:"

Jan 1, 1990

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By P. R. Richardson

"Milling is the weak link in the process chain of many mineral operations. While this activity accounts for only a relatively small proportion of the direct costs of most mineral processing complexes, there are intangible and indirect costs associated with milling which are extremely large. For example, significant opportunity costs are associated with the relatively low yields which characterize this stage of the process.There are changes abroad in the world which I believe are going to cause us to reformulate the whole concept of milling. Increased competition in mineral markets are going to force managers to look anew at the high mineral values reporting to tailings which are a high opportunity cost for many operations. Tailings recovery plants are not the ultimate solution to this problem. Greater environmental concerns are going to increase the costs associated with tailings disposal and force the mining industry to look for other ways to dispose of waste products. Technology changes currently underway in manufacturing and other process industries, such as the automated 'lights-out' plant are going to be brought into this industry, and the changes will be dramatic.These are major long term changes which probably seem rather remote to many managers and professionals in existing operations which are faced with much more mundane challenges arising from day-to-day operations. However, I believe that milling is increasingly a 'lean and keen' operation involving fewer and fewer people, but who are increasingly skilled and professional. Traditional cost management approaches are no longer adequate and the industry has to take a new look at the nature of cost reduction in this core activity. This stage in the mineral process provides opportunities for value creation leading to a significant unit cost advantage for the corporations willing to adopt a total cost approach."

Jan 1, 1988

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By Francis Gray

Mr. F. W. Gray: It is not my intention to read my paper as it is too long, so I will touch only on the high lights. The Sydney field is the most favourable example of undersea coal mining that exists, and I have not been able to find anything like it elsewhere. The nearest approach to it is a field in England where the Whitehaven collieries are operating, but it has a lot of faults. The net result of these faults so far met with in the seaward advance of the workings has been to increase, by something over 100 feet, the gain in depth of cover, in a distance of approximately three and three-quarter miles. In the Sydney field there are no faults of any consequence. On the east side, the English measures rise. In Australia the sea bottom fell and the cover became too light. On Vancouver Island the coal ran out, and in Japan the seams are steep and contorted. The Chilian fields resemble our own to some extent. An inundation of two collieries took place there some time ago, due, it is said, to the rise workings being allowed to approach the sea bottom too closely in the vicinity of a fault. The Cape Breton undersea field has been proved over a frontage of about thirty miles and has been attacked and penetrated for a considerable distance along that front. We have passed the prospecting stage and now generally use developed land areas as points of attack to win the undersea coal. Of our mining under the sea, it can be said that, with the exception of No. 1-B and Princess colliery, Sydney Mines, no real attempt has been made to win the undersea coal.

Jan 1, 1927

By Karl J. C. Harries

"3.1. INTRODUCTIONThis chapter discusses briefly the common law concepts of fiduciary relationship, constructive trust, and breach of confidence. Following a discussion of confidentiality agreements, the last section of the chapter compares and comments on two common law cases, the LAC Case and the Metalore Case. Civil law readers should not ignore this chapter or § 3.5. the comparison as, to a large extent, the concepts and comments are universal, even though the procedures for applying them may vary.1It should be appreciated that, regardless of the legal system, if the Court sees that a wrong has been done, it will attempt to right that wrong, either by awarding monetary damages against the wrong-doer to compensate the injured party or by attempting to make the injured party whole again by such means as negating an agreement (as in the Metalore Case) or returning property to a wronged party (as in the LAC Case). The methodology for accomplishing either of these results will vary with the jurisdiction, and the two are not mutually exclusive.These two Ontario cases have been chosen, not because they are the only ones available – they certainly are not – but because both are relatively well known within the minerals industry and they deal with problems that may face any explorationist (although it is to be hoped that the facts of the Metalore Case do not represent “normal” behaviour). Each judgment offers useful guidelines, as well as insight into a judge’s approach to problems, the type of information he expects to receive, how his mind works, and, particularly in the Court of Appeal judgment in the Metalore Case, how he might reason through and “justify” his decisions.3.2. SOME LEGAL CONCEPTS In order to appreciate some of the matters discussed in this chapter, it is necessary to have some idea of the common law considerations of fiduciary relationships, constructive trust, and breach of confidence."

Jan 1, 2003

By Robert E. McIvor

"The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill’s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “circuit classification system efficiency” (or CSE, McIvor, 1988a), and ultimately the discovery of the Functional Performance Equation (McIvor, 1988b, and McIvor et al, 1992). The CSE is the percentage of “coarse” (typically with reference to the plus P80) size material occupying the mill (versus “fines” or product size material, finer than the circuit P80), and can be calculated by taking the average of the percentage of coarse material in the mill feed and mill discharge. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, which is derived as follows.We define “fines” as any product size material, and “coarse” as that targeted to be further ground, the two typically differentiated by the circuit target P80. For any grinding circuit, the production rate of new, product size material (fines) must equal the specific grinding rate of the coarse material (i.e. fine product generated per unit of energy applied to the coarse material) times the power applied to the coarse material."

Jan 1, 2009

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004