Search Documents

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department?s Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By H. C. Fowler

The social economy, or public interest, and national defense require wise development and efficient use of the oil and gas resources of the United States. In this development and use, and in the prevention of economic and physical waste of oil and gas, the objectives of the petroleum and natural-gas industries, the Government (Federal, State, and local), and the public are the same. Differences of viewpoint generally have originated in the failure of one of the triad to have a clear or complete understanding of the motives behind the activities of the other component groups or full knowledge of what each is trying to accomplish. The Unites States Bureau of Mines through its petroleum and natural-gas division makes technologic and scientific investigations pertaining to recovery,3 preparation, refining, and use of oil and natural gas with the view of reducing waste, increasing safety and efficiency and aiding economic development.

Jan 1, 1933

By J. R. Thoenen

In Progress Rerort 1,4/ a number of facto were demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By E. H. Boyle

The Bureau of Mines has evaluated the potential availability of silver from 436 mines and deposits in 41 market economy countries (MEC?s) comprising five major economic categories of deposits: predominantly silver deposits and predominantly zinc, lead, copper, and gold deposits. This study evaluated the long-term cost and availability of primary silver production from 53 producing and 13 nonproducing predominantly silver properties in 11 MEC's and estimated the total recoverable silver from 370 properties as a coproduct or byproduct of zinc, lead, copper, or gold production. This study resulted in estimates of a demonstrated resource of 5.99 billion tr oz of recoverable silver as of January 1984. Of this total, 23.5 pet is in the 66 mines and deposits classified as predominantly silver properties. The largest quantity of recoverable silver, 43.9 pct, lies in the 121 properties classified as predominantly zinc, with 26.5 pct in 120 properties classified as predominantly copper, 4.1 pet in 21 predominantly lead properties, and 2.0 pct in 108 predominantly gold properties. At current silver prices, the economics of silver production favor silver that is a byproduct or coproduct of zinc, lead, copper, or gold, and much of the silver production in the United States from the predominantly silver mines is at an economic disadvantage in comparison with silver production in other countries.

Jan 1, 1986

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

The XVIth International Conference on Coal Mine Safety Research was divided into eight half-day technical sessions. In accord with the established practice of these conferences, at each session, presentation of the papers was followed by a discussion period. Questions and comments submitted in writing to the session chairman were answered or discussed by the authors of the relevant papers or by their representatives. These discussions were tape-recorded in the original language of the speaker and subsequently translated into English when necessary. Questions to which no answer was available at the time and a few comments that exceeded the scope of the session have been omitted.

Jan 1, 1975

This publication contains eight papers presented at a Bureau of Mines Technology Transfer Symposium in Charleston, W, on June 22, 1983, Five of the papers describe the results of Bureau-sponsored research on cabs and canopies for low-coal underground mining equipment. The other papers describe the efforts of three underground coal mining equipment manufacturers (FMC, Joy, and Lee-Norse) in the area of cab and canopy design.

Jan 1, 1985

Research workers From the Bureau of Mines and industry met with other government and industry representatives in Pittsburgh, Pa., on January 22, 1975, to discuss the results of research under the Bureau of Mines Noise Control Program. The program, aimed at reducing noise in mines, is functionally divided into three major areas: Instrumentation, personal protection, and noise abatement. This proceedings contains the opening remarks to the seminar and seven technical presentations based on various aspects of noise abatement and control.

Jan 1, 1975

Objective A cable bolt can be a strain-measuring device as well as a supporting device in underground mines. Placing instruments on a cable bolt allows certain characteristics of a rock mass, such as high strain and load, to he evaluated during mining and provides a means for mining engineers and mine inspectors to forecast a potential roof fall. Background Thousands of cable bolts are installed in U.S. mines each year. Studies performed by NIOSH researchers show that support loads can exceed the yield point of the steel, which can result in unstable ground conditions that pose direct safety hazards for underground workers. Rock falls can also create secondary hazards, such as caved escape ways and blocked ventilation passages. Development of methods and tools to assist in the evaluation and selection of rock supports could reduce the number of unplanned rock falls significantly. Approach Instrumented cable bolts developed at NIOSH’s Spokane Research Laboratory were used along with existing ground control systems to monitor rock mass loads and movement Axial and shear loads on the cables are determined as these loads are transferred to strain gages embedded in the king wire. In longwall, room-and-pillar, or underhand cut-and-fill mines, rock mass loads and movements can be detected down to microstrains of stress or millimeters of movement. By detecting such small amounts of ground movement and support load, early intervention to prevent a roof fall is possible, and miner safety and health are increased. How it Works Up to 10 strain gages are embedded in the king wire at whatever locations a mine ground control engineer may specify. The gages m either be set in pairs in the same plane to detect shear or set at 90° angles to detect loading in three dimensions. The cables are up to 5 meters long if they arc to be grouted with resin or up to 15 meters: if they will be grouted with cement. They arc capable of holding m ultimate lend of 214 kN and produce reliable readings to 178 kN, as shown in the calibration curve. The cables are fitted with an instrument plug for monitoring the gages and a special head for insertion into the rock. A data acquisition system, such as a Vishay strain indicator box, Campbell Scientific, or Omnidata system, is required to obtain the data for load and displacement calculations.

Nov 1, 1998

This dictionary is published by the Bureau of Mines as a contribution to the mining and mineral literature in the belief that it will fill a recognized need. Several attempts have been made over the years to revise Albert Fay's Glossary of the Mining and Mineral Industry which first appeared in December of 1918. Frank L. Hess of the Bureau of Mines worked on a revision, but his untimely death prevented its completion. Subsequently, the writer was employed to compile and edit this dictionary in cooperation with the technical staff of the Bureau of Mines. Fay's glossary contained about 18,000 terms with 27,000 definitions; the present compilation contains about 55,000 terms with approximately 150,000 definitions. These terms are of both a technical and local nature, and they apply to metal mining, coal mining, quarrying, geology, metallurgy, ceramics and clays, glassmaking, minerals and mineralogy, and general terminology. Petroleum, natural gas, and legal mining terminology, unless of a general nature, has been excluded, as has been foreign terminology where there is an English equivalent. Several thousand Spanish-American mining terms that appeared in Fay's compilation have been removed to make way for the thousands of new English terms that have evolved over the years. Those Spanish-American and Mexican terms still used in the Southwestern United States have been retained.

Jan 1, 1968

By Van H. Manning

Of all the war work by the Bureau of Mines none ultimately covered such a variety of processes and equipment, employed as many men, or called for as large an outlay as that started in con- nection with the solution of problems relating to the use of noxious gases in warfare. Beginning with an investigation to develop the best type of gas mask, the scope of the work extended until it included researches relating to a wide range of devices, such as different types of poisonous and irritating gases and smokes, smoke screens, gas shells and gas bombs, flame throwers, trench projectors for firing gas bombs, signal lights, and incendiary bombs. The Bureau of Mines in starting this work selected the necessary personnel, pro- cured the early equipment, and for some months, from the begin- ning to June 30, 1917, paid the cost of the work from its own funds. The Bureau of Mines built up a research staff of more than 700 chemists, including many of the most prominent chemists in the country, and obtained the cooperation of many of the universities and chemical companies. When the results obtained through this research were to be applied by the War Department, the Director of the Bureau of Mines cooperated in the selection of men to have charge of manufacture or further development, recommending chemiste who subsequently received commissions in the Army. The personal cooperation with the War Department was thus very close. The bureau can fairly claim that because it started this work on gas warfare and received the hearty support of the Department of War, the Navy Department, the National Research Council, and State, educational, and private institutions, the country was in July, 1918, months ahead of where it would otherwise have been in the production of gas masks and other devices. The production of toxic gases then far exceeded the supply of shells. In addition the later work in gas-mask manufacture by the Surgeon General's Office of the Army, which resulted in the development of the best mask produced anywhere; in gas manufacture and gas proving-ground tests by the Bureau of Ordnance, and in the chemical warfare pro- gram of the Navy, including the use of smoke screens, shells and toxic gases, were the direct results of the bureau's experimental work. The American charcoal and soda lime, developed through the research work, are the best used by any nation. The Bureau of Mines was instrumental in developing satisfactory methods of manu- facturing chlorpicrin, phosgene, mustard gas, brombenzylcyanide, cyanogen chloride, and other noxious substances on a large scale. The bureau also developed a smoke funnel for the Navy which no doubt saved many ships from submarine attacks, and devised smoke barrages, signal lights, incendiary darts, etc., for the Army. The Ordnance Department of the Army asked for incendiary bombs and were furnished with bombs better than any made previously. Perhaps the greatest single result of the research work has been the demonstration of the value of the services that the chemist and chemical engineer can render in time of need and the recogni- tion of chemical investigations as a necessary function of the Gov- ernment.

Jan 1, 1919

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007

Real economic growth for 1988 may fall short of the 3.3% projected by the Department of Commerce in August 1988 because the summer drought and intense heat in many areas curtailed output more severely than expected. The economy grew at an average annual rate of 3.0% for the first three quarters of the year, slowing in the second and third quarters. Export growth, which occurred even as the dollar edged up compared with other industrial country currencies, was an important factor in the expansion. Notable gains were posted in sales of machinery, computers, aircraft, chemicals, and telecommunications equipment. Imports increased, but not as much as exports, and the U.S. trade position was still much improved from that of 1987. Personal consumption expenditures grew slightly faster than the economy as a whole. Purchases of consumer durables showed notable strength in the first half of 1988, but slowed down in the third quarter. Despite the moderate rise in interest rates, business spending for new plant and equipment also rose and contributed to 1988 gross national product (GNP) growth. Both new business investment and export demand spurred orders for U.S.-made machine tools. Orders for machine tools for the first 8 months of 1988 were almost triple those in the corresponding period in 1987.

Jan 1, 1989

1. Domestic Production and Use: In 1983, 12 companies operated 27 primary aluminum reduction plants, with 4 firms accounting for 65% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Maryland, New York, Ohio, and West Virginia 35%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central States 16%. Based on published producer prices, output of primary metal in 1983 was valued at over $5.7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 37% of domestic consumption in 1983, transportation 19%, building 17%, electrical 9%, consumer durables 8%, and other uses 10%.

Jan 1, 1984

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By A. E. Wells

A critical study of the wet Thiogen process for extracting sulphur from the smoke of smelters is one of several investigations related to the general smelter-smoke problem that are being conducted under the direction of the Bureau of Mines. Part of the work done in the pyrometallurgical section of the cooperative metallurgical exhibit of the Bureau of Mines at the Panama-Pacific International Exposition during 1915 related to this investigation, and at the expiration of the exposition, the work was continued in the labora- tories of the Bureau of Mines in the Hearst Memorial Mining Building of the University of California, Berkeley, Cal., where a mining experiment station of the bureau has been established under the cooperative agreement with the University of California. Early in the spring of 1915, when plans were being made to co- operate with several metallurgical interests, the Thiogen Co. proposed to the Bureau of Mines that, along with the studies of various pro- posed methods for eliminating sulphur dioxide from smelter smoke, there should be included a study of the wet Thiogen process. In the study as outlined it was proposed to determine whether it would be technically and commercially feasible to use the, process for the recovery of elemental sulphur from the sulphur dioxide in waste smelter gases. Although there had been no large-scale work with the process, either in the laboratory or at a smelter, representatives of the metallur- gical and mining industry had shown considerable interest in the proposed method, and the desire had been expressed that a better knowledge of the possibilities of the process should be obtained. Thus, cooperation with the Thiogen Co. seemed justified by the in- terests of the metallurgical industry, and by the conservation promised by the recovery of a product of market value from what is otherwise a waste, and in some instances a serious nuisance. In accepting the responsibility for directing this investigation, the officials of the Bureau of Mines were necessarily free to conduct the work in the manner they considered necessary to determine the facts. It was also understood that any information obtained was to be made available to all who might be interested and might be printed in a Bureau of Mines report. To cover the cost of laboratory equipment and supplies, and the payment of salaries of assistants, other than Bureau of Mines employees, the Thiogen Co. in May, 1915, deposited with the cooperative metallurgical exhibit fund a sum considered sufficient to warrant starting the laboratory investi- gation. The origin and organization of this fund has been described by Clevenger and the author." In outlining the program for this investigation it was hoped that ultimately a small complete plant would be erected and the investi- gation center around the operation of the plant. However, pre- liminary to the erection of the plant, a laboratory study of the proc- ess was considered necessary, as the technical features of the process could be determined, it was believed, as satisfactorily on a smaller scale as on the scale first proposed. However, it was realized at the time that it would not be possible to determine so satisfactorily or definitely the commercial possibilities of the process on the scale of work adopted as in the larger operating plant. With this fact in mind it was planned that, if the study of the technical features on a laboratory scale gave sufficient promise of the process being commer- cially feasible, an operating unit should, if possible, be constructed later, and that more definite information concerning the commercial prospects should be determined. The investigations were started in June, 1915. In June and July work was confined entirely to small-scale laboratory tests, in which a careful study of the chemical reactions involved was made. In August, tests on a larger scale were started, and these were con- tinued until December, small-scale tests being made at the same time. On December 1, 1915, all work on the Thiogen process was discon- tinued temporarily, as the close of the exposition necessitated moving the laboratories. Work on the Thiogen process was started again in January, 1916, in the laboratories of the new mining experiment sta- tion at Berkeley, Cal., and was continued during the spring of 1916 until a point was reached where it was felt that the essential parts of the process had been carefully covered, and that some definite state- ments concerning the technical features and possibilities of the process, as given in this report, were warranted.

Jan 1, 1917