Search Documents

By J. Paraszczak

Metal mining at great depths presents a number of serious challenges for mine operators. Among them is the high demand for fresh air required to cool down mine openings, evacuate noxious gases and contaminants and provide sufficient amounts of oxygen for miners. At the same time, modern mechanized mines extensively use diesel-powered load-haul-dump (LHD) machines, trucks and other mobile equipment. These vehicles not only emit exhaust gases and diesel particulate matter (DPM), but constitute an additional source of heat. As mine regulations get steadily more stringent with regard to air quality, the use of diesel engines has an additional adverse impact on ventilation costs. In this context, the present paper examines possible alternatives for diesel power trains, both those commercially available and those in development. They are reviewed with regard to their principles, required infrastructure, stage of technology development and progress. The questions of their flexibility, practicality and economic viability are also addressed. Finally, their possible benefits and potential for implementation in the conditions of deep metal mines are discussed. The paper concludes with short- to medium-term predictions concerning promising drive alternatives for vehicles destined to operate in deep metal mines.

Jan 1, 2009

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By Michael Rieber

Mineral economics interfaces the mineral sciences and engineering with finance and economics in the analysis of appropriate questions facing the minerals and energy industries. Its practitioners include those trained in the earth sciences; mining, petroleum, and geological engineering; metallurgy and mineral preparation; as well as finance, information systems, economics, and statistics-most usefully in one or more combinations. Allowing for some overlap, three general areas may be identified: evaluation, economic analysis, and resource appraisal. Evaluation begins with mine investment analysis (exemplified by Gentry and O'Neil, 1984) and process costing, for which the STRAMM Handbook (Anon., 1977) provides a well-known basis for mining and beneficiation. But it extends from property appraisal, often used for the determination of taxes and royalties, through the determination and comparison of transport costs (e.g., Richer and Soo, 1977), and to benefit/cost analyses of externalities. Economic analysis, the subject of this section, is displayed in rigor and extent both theoretically and as applied to commodity classes in Vogely (1985), but it is implicit though apparent throughout Lefond (1983). The text edited by Vogely places minerals in their aggregative context with economic growth and trade, proceeds to the theoretical analysis of minerals and their markets, analyzes the structure and performance of the major mineral sectors, and concludes with policy issues: fuel, nonfuel, and environmental. Resource appraisal employs quantitative methods for the estimation of mineral and energy resources. It moves through geologic, geophysical, and geochemical properties to the identification of estimation procedures for mineral endowment and for the economic measure of stocks and flows of specific minerals (Harris, 1984). It can be used to estimate the probable amount of a specific resource remaining in a given region and has been used to project sites in a specific

Jan 1, 2008

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency has been widely used by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which follows. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided. The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies. OUTLINE Introduction and Background Part 1. Determining the Bond Efficiency of a Grinding Circuit Method Demonstration/Example Calculations Bond Work Index Testing Equipment and Procedures Accuracy of Comparative Circuit WI Efficiency Determinations (under development) List of Symbols Part 2. Data Base of Bond Grinding Circuit Efficiencies (under development) References Annexes: A1. The Bond Crushing WI Test Equipment and Procedure for Bond Efficiency Determinations (Revised March 26, 2015) B1. The Bond Rod Mill WI Test Equipment and Procedure (Revised March 26, 2015) C1. The Bond Ball Mill WI Test Equipment and Procedure (Revised March 26, 2015) Introduction and Background Please see the references and slide presentation “Bond Efficiency SLC (rev3)-print.pdf.” This efficiency determination applies to most brittle materials in their naturally occurring (un-scalped) size distributions being treated in size reduction circuits down to a product sizing of approximately eighty percent passing 70 µm (see below). Unusually shaped materials (e.g. mica) should be regarded with caution. Part 1. Determining the Bond Efficiency of a Grinding Circuit Method In the plant: • Define the circuit for which the WI efficiency is to be determined • Procure samples of the circuit feed and product • Obtain the power draw of the size reduction equipment at the drive pinion(s) • Obtain the circuit throughput rate (dry tonnage) In the laboratory:"

Jan 1, 2016

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By Richard L. Gordon

At almost no time since the end of World War I has the coal industry been free from serious threats to its competitive position. At present, the critical question is whether the industry can maintain its position in the electric power market and this paper reviews the prospects in this area. Our report is part of a study, supported by Resources for the Future Inc., dealing with coal demand in general. Like most elements of coal economics, it has received much less analysis than problems in other energy sectors--a defect we felt worth correcting. We have concentrated on electric power elements of the market. The nature of the coal market makes this the natural choice. Three markets absorb over 80 per cent of coal production and are considered in our overall work. The completely excluded sectors are largely catchall categories in which coal use is declining anyway. Comparing the three markets included in the overall study, we see: modest growth is the most optimistic forecast for metallurgical coke; export growth depends to a large extent on policies of foreign governments. Electric power use, however, has rapidly grown to absorb over half of coal output and coal's prospects depend almost entirely on continued expansion of this market. Throughout the 1960's the demand for coal used to generate electrical power in the United States grew at an average rate of 6.5 per cent annually. This growth rate will be sustained until at least 1976.

Jan 1, 1971

By Juan Camus

To understand why some companies excel in creating value, Jim Collins (2001) and a group of postgraduate business students engaged in a comprehensive, five-year research project. They examined 1,435 U.S. companies for more than 40 years, seeking those that made significant improvements in their financial performance over time. The distinctive pattern sought was: ?Fifteen-year cumulative stock returns at or below the general stock market, punctuated by a transition point, then cumulative returns at least three times the market over the next 15 years. ?The search identified 11 outperforming companies, all in different industries, that were called the ?good to great? companies. To contrast these companies with similar peers within the same industry, the search also selected a group of comparison companies that failed to make the leap from good to great. Collins then set out to examine the transition point. What distinguishing features did the good-to-great companies have that their industry counterparts did not? At the heart of the findings about these outstanding companies is what Collins refers to as the ?hedgehog concept? ? how to find the one big thing that the company must focus on. According to Collins, those who built the good-to-great companies were, to one degree or another, hedgehogs. Those who led the comparison companies tended to be foxes, never gaining the clarifying advantage of a hedgehog concept, being instead scattered, diffused and inconsistent. This insight is complemented by Peter Drucker (2004), an influential management guru, who asserts that the first question an effective executive should ask is: ?what needs to be done?? Asking this question and taking it seriously, he asserts, is crucial for managerial success; and that the answer almost always has more than one urgent task, but the effective leader only concentrates on one task. In this last respect, Drucker emphasizes: ?If they [executives] are among the sizeable minority who work best with a change of pace in the working day, they pick two tasks. I have never encountered an executive who is effective while tackling more than two tasks at a time.?

Jan 1, 2011

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By George Schmitt, Ted Dowey, Grant Millener, Sean McAndrew, Eric Jordan

The Rondout-West Branch Bypass Tunnel is being built to bypass a substantial leak in New York City’s primary water supply tunnel. The 13,500 foot long tunnel travels 600 feet under the Hudson River through the same troubled geology and high pressure water inflows that the original tunnel did in the 1940s. A Robbins TBM traversed this geology and built gasketed segments. Nine thousand two hundred feet of 16 foot diameter interliner was installed and backfilled within the segments. Finally, reinforced cast in place lining was placed. This paper addresses the challenges and the multi-tasking approach the contractor utilized.

Jun 13, 2021

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Our universities and other training institutions are doing just fine meeting the traditional skill needs required by the industry. But are the skill needs going to be the same in the near future? The answer may be NO!! Mining is changing: increased liabilities and costs of environmental and safety issues; lower grades of minerals in traditional mining activities; the advent of new bio-chemical processes and robotic equipment as more productive and economic alternatives; and, larger more sophisticated and automatic equipment. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs, and productivity. And we will be engaging in more undersea mining, possibly space bases processing, less human interaction, and more remote control of events than was ever thought possible in the past. This paper presents several of the systemic changes that are presently and will continue to change the face of mining. It will identify area where education and management will have to address these changes.

Jan 1, 2011

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 1998

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994